Added DKL Phy sequences and helpers functions to program voltage
swing, clock gating and dp mode.

It is not written in DP enabling sequence but "PHY Clockgating
programming" states that clock gating should be enabled after the
link training but doing so causes all the following trainings to fail
so not enabling it for.

v2:
Setting the right HIP_INDEX_REG bits (José)

v3:
Adding the meaning of each column of tgl_dkl_phy_ddi_translations
Adding if gen >= 12 on intel_ddi_hdmi_level() and
intel_ddi_pre_enable_hdmi() instead of reuse part of gen >= 11 if

v4:
Moved the DP_MODE lane programing to another patch as ICL also
needed it
Sharing icl_phy_set_clock_gating() and icl_program_mg_dp_mode() with
TGL as bits and programing as now it almost identical to ICL

BSpec: 49292
BSpec: 49190

Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-2-jose.souza@intel.com

BSpec was updated(r146548) with a new MG_DP_MODE Programming table,
now taking in consideration the pin assignment and allowing us to
optimize power by shutting down available but not needed lanes.

It was tested on ICL and TGL, with adaptors that used pin assignment
C and B, reversing the connector and going to different modes testing
the not needed lane shutdown.

v5:
Using crtc_state->lane_count instead of dp.lane_count

BSpec: 21735
BSpec: 49292

Cc: Imre Deak <imre.deak@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926210659.56317-1-jose.souza@intel.com

We have a new version of DMC for ICL - v1.09.

This version adds the Half Refresh Rate capability
into DMC.

Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925201250.18136-1-daniele.ceraolospurio@intel.com

The HuC FW has silently switched to encoding the version the same way as
the GuC FW does, i.e. major.minor.patch instead of just major.minor. All
the current blobs follow the new scheme, but since minor and patch are
both zero there is no difference in the end results and we happily load
them. New binaries, however, will have non-zero values in there, so we
need to make sure to parse them correctly.

Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Acked-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925222121.4000-1-daniele.ceraolospurio@intel.com

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

Continuing the theme of breaking intel_pm.c up in a reasonable chunk of
powermanagement utilities, pull out the rc6 setup into its GT handler.

Based on a patch by Chris Wilson.

Signed-off-by: Andi Shyti <andi.shyti@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190919143840.20384-1-andi.shyti@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20190927110849.28734-1-chris@chris-wilson.co.uk

The simplest and most maximal submission we can do, a thread to submit
requests unto each engine.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925193446.26007-1-chris@chris-wilson.co.uk

We can use it in i915 for updating parts of unmasked registers from
within a batch. We're also adding Gen8+ versions of CS_GPR registers
(aka MI_MATH_REG in the coprocessor).

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926100635.9416-4-michal.winiarski@intel.com

Insert structure members names into their descriptions to follow
kernel-doc format.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Anna Karas <anna.karas@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926122158.13028-1-anna.karas@intel.com

The function intel_engine_breadcrumbs_irq() is always invoked from an interrupt
handler and for that reason it invokes (as an optimisation) only spin_lock()
for locking assuming that the interrupts are already disabled. The
function intel_engine_signal_breadcrumbs() is provided to disable
interrupts while the former function is invoked so that assumption is
also true for callers from preemptible context.

On PREEMPT_RT local_irq_disable() really disables interrupts and this
forbids to invoke spin_lock() which becomes a sleeping spinlock.

This is also problematic with `threadirqs' in conjunction with
irq_work. With force threading the interrupt handler, the handler is
invoked with disabled BH but with interrupts enabled. This is okay and
the lock itself is never acquired in IRQ context. This changes with
irq_work (signal_irq_work()) which _still_ invokes
intel_engine_breadcrumbs_irq() from IRQ context. Lockdep should see this
and complain.

Acquire the locks in intel_engine_breadcrumbs_irq() with _irqsave()
suffix and let all callers invoke intel_engine_breadcrumbs_irq()
directly instead using intel_engine_signal_breadcrumbs().

Reported-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926105644.16703-2-bigeasy@linutronix.de

The lockdep_assert_irqs_disabled() check is needless. The previous
lockdep_assert_held() check ensures that the lock is acquired and while
the lock is acquired lockdep also prints a warning if the interrupts are
not disabled if they have to be.
These IRQ-off asserts trigger on PREEMPT_RT because the locks become
sleeping locks and do not really disable interrupts.

Remove lockdep_assert_irqs_disabled().

Reported-by: Clark Williams <williams@redhat.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926105644.16703-3-bigeasy@linutronix.de

Default length value of MI_LOAD_REGISTER_REG is 1.
Also move it out of cmd-parser-only registers since we're going to use
it in i915.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-3-chris@chris-wilson.co.uk

Some of our commands (MI_FLUSH_DW / PIPE_CONTROL) require a post-sync write
operation to be performed. Currently we're using dedicated VMA for
PIPE_CONTROL and global HWSP for MI_FLUSH_DW.
On execlists platforms, each of our contexts has an area that can be
used as scratch space. Let's use that instead.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-2-chris@chris-wilson.co.uk

We're currently using scratch presence as a way of identifying that we
entered wedged state at driver initialization time.
Let's use a separate flag rather than rely on scratch.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190926133142.2838-1-chris@chris-wilson.co.uk

According to the bspec, GLK/CNL have a smaller small joiner RAM buffer
than ICL+.  This feels like something that could easily change again on
future platforms, so let's just add a function to return the proper
per-platform buffer size.  That may also slightly simplify the upcoming
bigjoiner enabling.

Since we have to change intel_dp_dsc_get_output_bpp()'s signature to
pass the dev_priv down for the platform check, let's take the
opportunity to also make that function static since it isn't used
outside the intel_dp file.

v2: Minor rebase on top of Maarten's changes.

Bspec: 20388
Bspec: 49259
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925234542.24289-1-matthew.d.roper@intel.com

The memory type values have changed in TGL, so we need to translate them
differently than ICL. While we're moving it, fix up the ICL translation
for LPDDR4.

BSpec: 53998

v2: Fix up ICL LPDDR4 entry (Ville); Drop unused values from TGL (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924222829.13142-1-james.ausmus@intel.com

TGL added 2 more TC ports that currently are not being handled by
icl_pll_to_ddi_clk_sel(), so adding those.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reported-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-6-jose.souza@intel.com

Extending ICL mg calculations to also support dkl calculations.

v3:
Fixing iref_trim calculation for 38400 refclock

BSpec: 49204

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-5-jose.souza@intel.com

The final save operation into pll_state of the calculations done will
be different for DKL PHY. Prepare for that by reindenting code so it's
easier to check for correctness. This one has no change in behavior.

Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-4-jose.souza@intel.com

Add a new function to write to dkl phy pll registers. As per the
bspec all the registers are read modify write.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-2-jose.souza@intel.com

The disable function can be the same as for MG phy since the same
registers are used. The others are different as registers changed,
also adding a empty dkl_pll_write() to be implemented later.

v2:
Setting the right HIP_INDEX_REG bits (José)

v3:
Masking non-computed registers of mg_pll_tdc_coldst_bias
when getting hardware state
Sharing mg_pll_enable() with TGL

Reviewed-by: Imre Deak <imre.deak@intel.com>
Acked-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924210040.142075-1-jose.souza@intel.com

Having decided that we only care about the promotion predicate, we can
simplify gen12_csb_parse to simply check whether we need to jump to a
new queue.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925130845.17952-1-chris@chris-wilson.co.uk

We cannot switch between HQ and normal mode on GLK+, so only
add planes on platforms where it makes sense.

We could probably restrict it even more to only add when scaler
users toggles between 1 and 2, but lets just leave it for now.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-9-maarten.lankhorst@linux.intel.com


Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

Rename linked_plane to planar_linked_plane and slave to planar_slave,
this will make it easier to keep apart bigjoiner linking and planar plane
linking.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-8-maarten.lankhorst@linux.intel.com


Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

We had this as an optimization to not do a plane update, but we killed
it off because there are so many reasons we may have to do a plane
update or fastset that it's best to just assume everything changed.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920114235.22411-6-maarten.lankhorst@linux.intel.com


Reviewed-by: Matt Roper <matthew.d.roper@intel.com>

Readout the FEC state in encoder->get_config(), this will allow
us to ensure that we can correctly inherit the state from boot,
and that we set FEC during modeset.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-2-maarten.lankhorst@linux.intel.com


Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.

As a result our calculated bpp was way too high, and the link width
limitation never came into effect.

Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.

We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.

This fixes the FIFO underrun we are seeing with FEC enabled.

Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d9218c8f ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com


Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>

This reverts commit 84af7649.

This is causing problems with the display, displays are all
bright colors.

Fixes: 84af7649

 ("drm/i915/color: Extract icl_read_luts()")
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924135820.11850-1-swati2.sharma@intel.com

If we disable rps, it appears the Tigerlake is stable enough to run
multiple engines simultaneously in CI. As disabling rps should only
cause the execution to be slow, whereas many features depend on the
different engines, we would prefer to have the engines enabled while the
machine hangs are being debugged.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111714


Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924173501.21956-1-chris@chris-wilson.co.uk

Currently the offset for PIPE D cursor control register is missing in
i915_reg.h due to which the cursor plane cannot be enabled for Pipe D.
This also causes kernel Warning, when a user requests to enable cursor
plane for PIPE D for Gen 12 platforms.

This patch adds the CURSOR_CTL_D register in the i915_reg.h.

v2: Rebase

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111640


Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
[Lucas: remove extra blank line]
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1569310312-12313-1-git-send-email-ankit.k.nautiyal@intel.com

Before we submit the first context to HW, we need to construct a valid
image of the register state. This layout is defined by the HW and should
match the layout generated by HW when it saves the context image.
Asserting that this should be equivalent should help avoid any undefined
behaviour and verify that we haven't missed anything important!

Of course, having insisted that the initial register state within the
LRC should match that returned by HW, we need to ensure that it does.

v2: Drop the RELATIVE_MMIO flag from gen11, we ignore it for
constructing the lrc image.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190924145950.3011-1-chris@chris-wilson.co.uk

Added bandwidth calculation algorithm and checks,
similar way as it was done for ICL, some constants
were corrected according to BSpec 53998.

v2: Start using same icl_get_bw_info function to avoid
    code duplication. Moved mpagesize to memory info
    related structure as it is now dependent on memory type.
    Fixed qi.t_bl field assignment.

v3: Removed mpagesize as unused. Duplicate code and redundant blankline
    fixed.

v4: Changed ordering of IS_GEN checks as agreed. Minor commit
    message fixes.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111600


Reviewed-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920083754.5920-1-stanislav.lisovskiy@intel.com

Since dropping the set-to-gtt-domain in commit a679f58d ("drm/i915:
Flush pages on acquisition"), we no longer mark the contents as dirty on
a write fault. This has the issue of us then not marking the pages as
dirty on releasing the buffer, which means the contents are not written
out to the swap device (should we ever pick that buffer as a victim).
Notably, this is visible in the dumb buffer interface used for cursors.
Having updated the cursor contents via mmap, and swapped away, if the
shrinker should evict the old cursor, upon next reuse, the cursor would
be invisible.

E.g. echo 80 > /proc/sys/kernel/sysrq ; echo f > /proc/sysrq-trigger

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111541
Fixes: a679f58d

 ("drm/i915: Flush pages on acquisition")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.2+
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920121821.7223-1-chris@chris-wilson.co.uk

Force bonded requests to run on distinct engines so that they cannot be
shuffled onto the same engine where timeslicing will reverse the order.
A bonded request will often wait on a semaphore signaled by its master,
creating an implicit dependency -- if we ignore that implicit dependency
and allow the bonded request to run on the same engine and before its
master, we will cause a GPU hang. [Whether it will hang the GPU is
debatable, we should keep on timeslicing and each timeslice should be
"accidentally" counted as forward progress, in which case it should run
but at one-half to one-third speed.]

We can prevent this inversion by restricting which engines we allow
ourselves to jump to upon preemption, i.e. baking in the arrangement
established at first execution. (We should also consider capturing the
implicit dependency using i915_sched_add_dependency(), but first we need
to think about the constraints that requires on the execution/retirement
ordering.)

Fixes: 8ee36e04 ("drm/i915/execlists: Minimalistic timeslicing")
References: ee113690

 ("drm/i915/execlists: Virtual engine bonding")
Testcase: igt/gem_exec_balancer/bonded-slice
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-3-chris@chris-wilson.co.uk

Due to the nature of preempt-to-busy the execlists active tracking and
the schedule queue may become temporarily desync'ed (between resubmission
to HW and its ack from HW). This means that we may have unwound a
request and passed it back to the virtual engine, but it is still
inflight on the HW and may even result in a GPU hang. If we detect that
GPU hang and try to reset, the hanging request->engine will no longer
match the current engine, which means that the request is not on the
execlists active list and we should not try to find an older incomplete
request. Given that we have deduced this must be a request on a virtual
engine, it is the single active request in the context and so must be
guilty (as the context is still inflight, it is prevented from being
executed on another engine as we process the reset).

Fixes: 22b7a426

 ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-2-chris@chris-wilson.co.uk

As preempt-to-busy leaves the request on the HW as the resubmission is
processed, that request may complete in the background and even cause a
second virtual request to enter queue. This second virtual request
breaks our "single request in the virtual pipeline" assumptions.
Furthermore, as the virtual request may be completed and retired, we
lose the reference the virtual engine assumes is held. Normally, just
removing the request from the scheduler queue removes it from the
engine, but the virtual engine keeps track of its singleton request via
its ve->request. This pointer needs protecting with a reference.

v2: Drop unnecessary motion of rq->engine = owner

Fixes: 22b7a426

 ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-1-chris@chris-wilson.co.uk

New step added for TGL, required for us to check the TC
microcontroller health after power on TC aux.

BSpec: 49294

Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-7-jose.souza@intel.com

Adding a enable parameters allow us to share most of the code between
enable and disable functions.

v3:
Renamed icl_phy_clock_gating() to icl_phy_set_clock_gating()

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-6-jose.souza@intel.com

These are the registers needed to program Dekel phy. Some register
definitions will be reused from MG PHY definitions, so adding a
comment on those.

Bspec: 49295

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-5-jose.souza@intel.com

Commit 24a7bfe0

 ("drm/i915: Keep the TypeC port mode fixed when the
port is active") added this new hook while in parallel TGL upstream was
happening and this was missed.

Without this driver will crash when TC DDI is added and driver is
preparing to do a full modeset.

Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Clinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-4-jose.souza@intel.com