- Jan 18, 2019
-
-
Yang Wei authored
Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch, perf) friendly. Signed-off-by:
Yang Wei <yang.wei9@zte.com.cn> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Lendacky, Thomas authored
The XGBE hardware has support for performing MDIO operations using an MDIO command request. The driver mistakenly uses the mdio port address as the MDIO command request device address instead of the MDIO command request port address. Additionally, the driver does not properly check for and create a clause 45 MDIO command. Check the supplied MDIO register to determine if the request is a clause 45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device address and register number from the supplied MDIO register and use them to set the MDIO command request device address and register number fields. For a clause 22 operation, the MDIO request device address is set to zero and the MDIO command request register number is set to the supplied MDIO register. In either case, the supplied MDIO port address is used as the MDIO command request port address. Fixes: 732f2ab7 ("amd-xgbe: Add support for MDIO attached PHYs") Signed-off-by:
Tom Lendacky <thomas.lendacky@amd.com> Tested-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Camelia Groza authored
The phy drivers for CS4340 and TN2020 are missing their features attributes. Add them. Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap") Reported-by:
Scott Wood <oss@buserror.net> Signed-off-by:
Camelia Groza <camelia.groza@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Madalin Bucur authored
As txq_trans_update() only updates trans_start when the lock is held, trans_start does not get updated if NETIF_F_LLTX is declared. Signed-off-by:
Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yunjian Wang authored
The skb header should be set to ethernet header before using is_skb_forwardable. Because the ethernet header length has been considered in is_skb_forwardable(including dev->hard_header_len length). To reproduce the issue: 1, add 2 ports on linux bridge br using following commands: $ brctl addbr br $ brctl addif br eth0 $ brctl addif br eth1 2, the MTU of eth0 and eth1 is 1500 3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4) from eth0 to eth1 So the expect result is packet larger than 1500 cannot pass through eth0 and eth1. But currently, the packet passes through success, it means eth1's MTU limit doesn't take effect. Fixes: f6367b46 ("bridge: use is_skb_forwardable in forward path") Cc: bridge@lists.linux-foundation.org Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com> Cc: Roopa Prabhu <roopa@cumulusnetworks.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
Yunjian Wang <wangyunjian@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jason Wang authored
Vhost dirty page logging API is designed to sync through GPA. But we try to log GIOVA when device IOTLB is enabled. This is wrong and may lead to missing data after migration. To solve this issue, when logging with device IOTLB enabled, we will: 1) reuse the device IOTLB translation result of GIOVA->HVA mapping to get HVA, for writable descriptor, get HVA through iovec. For used ring update, translate its GIOVA to HVA 2) traverse the GPA->HVA mapping to get the possible GPA and log through GPA. Pay attention this reverse mapping is not guaranteed to be unique, so we should log each possible GPA in this case. This fix the failure of scp to guest during migration. In -next, we will probably support passing GIOVA->GPA instead of GIOVA->HVA. Fixes: 6b1e6cc7 ("vhost: new device IOTLB API") Reported-by:
Jintack Lim <jintack@cs.columbia.edu> Cc: Jintack Lim <jintack@cs.columbia.edu> Signed-off-by:
Jason Wang <jasowang@redhat.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
net_tstamp.h is an UAPI header, so it was moved under include/uapi. Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Nicolas Dichtel authored
Since commit cb9f1b78, scapy (which uses an AF_PACKET socket in SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel: Here is a example of the setup: $ ip link set ntfp2 up $ ip addr add 10.125.0.1/24 dev ntfp2 $ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2 $ ip addr add fd00:cafe:cafe::1/128 dev tun1 $ ip link set dev tun1 up $ ip route add fd00:200::/64 dev tun1 $ scapy >>> p = [] >>> p += IPv6(src='fd00:100::1', dst='fd00:200::1')/ICMPv6EchoRequest() >>> send(p, count=1, inter=0.1) >>> quit() $ ip -s link ls dev tun1 | grep -A1 "TX.*errors" TX: bytes packets errors dropped carrier collsns 0 0 1 0 0 0 The problem is that the network offset is set to the hard_header_len of the output device (tun1, ie 14 + 20) and in our case, because the packet is small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes (ipv6 header) starting from the network offset). This problem is more generally related to device with variable hard header length. To avoid a too intrusive patch in the current release, a (ugly) workaround is proposed in this patch. It has to be cleaned up in net-next. Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3 Link: http://patchwork.ozlabs.org/patch/1024489/ Fixes: cb9f1b78 ("ip: validate header length on virtual device xmit") CC: Willem de Bruijn <willemb@google.com> CC: Maxim Mikityanskiy <maximmi@mellanox.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexey Kodanev authored
After commit 23b0269e ("net: udp6: prefer listeners bound to an address"), UDP-Lite only works when specifying a local address for the sockets. This is related to the problem addressed in the commit 719f8358 ("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now looks for a socket immediately in the secondary hash table. And this issue was found with LTP/network tests as well. Fixes: 23b0269e ("net: udp6: prefer listeners bound to an address") Signed-off-by:
Alexey Kodanev <alexey.kodanev@oracle.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexey Kodanev authored
After commit 4cdeeee9 ("net: udp: prefer listeners bound to an address"), UDP-Lite only works when specifying a local address for the sockets. This is related to the problem addressed in the commit 719f8358 ("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now looks for a socket immediately in the secondary hash table. The issue was found with LTP/network tests (UDP-Lite test-cases). Fixes: 4cdeeee9 ("net: udp: prefer listeners bound to an address") Signed-off-by:
Alexey Kodanev <alexey.kodanev@oracle.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ivan Vecera authored
Recent changes (especially 05cd271f ("cls_flower: Support multiple masks per priority")) in the fl_flow_mask structure grow it and its current size e.g. on x86_64 with defconfig is 760 bytes and more than 1024 bytes with some debug options enabled. Prior the mentioned commit its size was 176 bytes (using defconfig on x86_64). With regard to this fact it's reasonable to allocate this structure dynamically in fl_change() to reduce its stack size. v2: - use kzalloc() instead of kcalloc() Fixes: 05cd271f ("cls_flower: Support multiple masks per priority") Cc: Jiri Pirko <jiri@resnulli.us> Cc: Paul Blakey <paulb@mellanox.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Johan Hovold authored
Use the new of_get_compatible_child() helper to look up child nodes to avoid ever matching non-child nodes elsewhere in the tree. Also fix up the related struct device_node leaks. Fixes: d8652956 ("net: dsa: realtek-smi: Add Realtek SMI driver") Cc: stable <stable@vger.kernel.org> # 4.19: 36156f92 Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Colin Ian King authored
Shifting the 1 by exp by an int can lead to sign-extension overlow when exp is 31 since 1 is an signed int and sign-extending this result to an unsigned long long will set the upper 32 bits. Fix this by shifting an unsigned long. Detected by cppcheck: (warning) Shifting signed 32-bit value by 31 bits is undefined behaviour Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Jan 17, 2019
-
-
Willem de Bruijn authored
Failure __ip_append_data triggers udp_flush_pending_frames, but these tests happen later. The skb must be freed directly. Fixes: bec1f6f6 ("udp: generate gso with UDP_SEGMENT") Reported-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
The section of bpfilter UMH blob is the ".bpfilter_umh". but this is not an explicit section. so linking warning occurred at compile time for the powerpc. So, this patch makes use of the ".rodata" instead of the ".bpfilter_umh". Config condition: CONFIG_BPFILTER=y CONFIG_BPFILTER_UMH=y Result: ld: warning: orphan section `.bpfilter_umh' from `net/bpfilter/bpfilter_umh_blob.o' being placed in section `.bpfilter_umh' Fixes: 61fbf593 ("net: bpfilter: restart bpfilter_umh when error occurred") Reported-by:
Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
The bcm87xx and micrel driver has PHYs which are missing the .features value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed features definition of this PHY. Fixes: 719655a1 ("net: phy: Replace phy driver features u32 with link_mode bitmap") Reported-by:
Scott Wood <oss@buserror.net> Reported-by:
Camelia Groza <camelia.groza@nxp.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jakub Kicinski authored
"IPv6: " prefix is already added by pr_fmt, no need to include it again in the pr_warn() format. The message predates extack support, we can replace the whole thing with an extack message. Suggested-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Davide Caratti authored
In iproute2 commit 90c5c969f0b9 ("fix print_0xhex on 32 bit"), the format specifier for the ife type changed from 0x%X to %#llX, causing systematic failures in the following TDC test cases: 7682 - Create valid ife encode action with mark and pass control ef47 - Create valid ife encode action with mark and pipe control df43 - Create valid ife encode action with mark and continue control e4cf - Create valid ife encode action with mark and drop control ccba - Create valid ife encode action with mark and reclassify control a1cf - Create valid ife encode action with mark and jump control cb3d - Create valid ife encode action with mark value at 32-bit maximum 95ed - Create valid ife encode action with prio and pass control aa17 - Create valid ife encode action with prio and pipe control 74c7 - Create valid ife encode action with prio and continue control 7a97 - Create valid ife encode action with prio and drop control f66b - Create valid ife encode action with prio and reclassify control 3056 - Create valid ife encode action with prio and jump control 7dd3 - Create valid ife encode action with prio value at 32-bit maximum 05bb - Create valid ife encode action with tcindex and pass control ce65 - Create valid ife encode action with tcindex and pipe control 09cd - Create valid ife encode action with tcindex and continue control 8eb5 - Create valid ife encode action with tcindex and continue control 451a - Create valid ife encode action with tcindex and drop control d76c - Create valid ife encode action with tcindex and reclassify control e731 - Create valid ife encode action with tcindex and jump control b7b8 - Create valid ife encode action with tcindex value at 16-bit maximum 2a9c - Create valid ife encode action with mac src parameter cf5c - Create valid ife encode action with mac dst parameter 2353 - Create valid ife encode action with mac src and mac dst parameters 552c - Create valid ife encode action with mark and type parameters 0421 - Create valid ife encode action with prio and type parameters 4017 - Create valid ife encode action with tcindex and type parameters fac3 - Create valid ife encode action with index at 32-bit maximnum 7c25 - Create valid ife decode action with pass control dccb - Create valid ife decode action with pipe control 7bb9 - Create valid ife decode action with continue control d9ad - Create valid ife decode action with drop control 219f - Create valid ife decode action with reclassify control 8f44 - Create valid ife decode action with jump control b330 - Create ife encode action with cookie Change 'matchPattern' values, allowing '0' and '0x0' if ife type is equal to 0, and accepting both '0x' and '0X' otherwise, to let these tests pass both with old and new tc binaries. While at it, fix a small typo in test case fac3 ('maximnum'->'maximum'). Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Konstantin Khlebnikov authored
This should be 1 for normal allocations, 0 disables leak reporting. Signed-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reported-by:
Cong Wang <xiyou.wangcong@gmail.com> Fixes: 85704cb8 ("net/core/neighbour: tell kmemleak about hash tables") Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Xin Long authored
The similar issue as fixed in Commit 4a2eb0c3 ("sctp: initialize sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists in sctp_inetaddr_event, as Alexander noticed. To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist(). Reported-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Reported-by:
<syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Xin Long authored
As said in draft-foschiano-erspan-03#section4: Different frame variants known as "ERSPAN Types" can be distinguished based on the GRE "Protocol Type" field value: Type I and II's value is 0x88BE while Type III's is 0x22EB [ETYPES]. So set it properly in erspan_xmit() according to erspan_ver. While at it, also remove the unused parameter 'proto' in erspan_fb_xmit(). Fixes: 94d7d8f2 ("ip6_gre: add erspan v2 support") Reported-by:
Jianlin Shi <jishi@redhat.com> Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ross Lagerwall authored
For nested and variable attributes, the expected length of an attribute is not known and marked by a negative number. This results in an OOB read when the expected length is later used to check if the attribute is all zeros. Fix this by using the actual length of the attribute rather than the expected length. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dmitry Bezrukov authored
New device of TRENDnet based on aqc111u Add this ID to blacklist of cdc_ether driver as well Signed-off-by:
Dmitry Bezrukov <dmitry.bezrukov@aquantia.com> Signed-off-by:
Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Cong Wang authored
Martin reported a set of filters don't work after changing from reclassify to continue. Looking into the code, it looks like skb protocol is not always fetched for each iteration of the filters. But, as demonstrated by Martin, TC actions could modify skb->protocol, for example act_vlan, this means we have to refetch skb protocol in each iteration, rather than using the one we fetch in the beginning of the loop. This bug is _not_ introduced by commit 3b3ae880 ("net: sched: consolidate tc_classify{,_compat}"), technically, if act_vlan is the only action that modifies skb protocol, then it is commit c7e2b968 ("sched: introduce vlan action") which introduced this bug. Reported-by:
Martin Olsson <martin.olsson+netdev@sentorsecurity.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Jan 16, 2019
-
-
Timotej Lazar authored
Since the referenced commit, Ethernet fails to come up at boot on the board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the genphy_soft_reset callback for the Amlogic Meson GXL PHY driver. Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset") Signed-off-by:
Timotej Lazar <timotej.lazar@araneo.si> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
yupeng authored
add document for below counters: TcpEstabResets TcpAttemptFails TcpOutRsts TcpExtTCPSACKDiscard TcpExtTCPDSACKIgnoredOld TcpExtTCPDSACKIgnoredNoUndo TcpExtTCPSackShifted TcpExtTCPSackMerged TcpExtTCPSackShiftFallback TcpExtTCPWantZeroWindowAdv TcpExtTCPToZeroWindowAdv TcpExtTCPFromZeroWindowAdv TcpExtDelayedACKs TcpExtDelayedACKLocked TcpExtDelayedACKLost TcpExtTCPLossProbes TcpExtTCPLossProbeRecovery Signed-off-by:
yupeng <yupeng0921@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Both gue_err() and gue6_err() incorrectly assume linear skbs. Fix them to use pskb_may_pull(). BUG: KMSAN: uninit-value in gue6_err+0x475/0xc40 net/ipv6/fou6.c:101 CPU: 0 PID: 18083 Comm: syz-executor1 Not tainted 5.0.0-rc1+ #7 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: <IRQ> __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:600 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313 gue6_err+0x475/0xc40 net/ipv6/fou6.c:101 __udp6_lib_err_encap_no_sk net/ipv6/udp.c:434 [inline] __udp6_lib_err_encap net/ipv6/udp.c:491 [inline] __udp6_lib_err+0x18d0/0x2590 net/ipv6/udp.c:522 udplitev6_err+0x118/0x130 net/ipv6/udplite.c:27 icmpv6_notify+0x462/0x9f0 net/ipv6/icmp.c:784 icmpv6_rcv+0x18ac/0x3fa0 net/ipv6/icmp.c:872 ip6_protocol_deliver_rcu+0xb5a/0x23a0 net/ipv6/ip6_input.c:394 ip6_input_finish net/ipv6/ip6_input.c:434 [inline] NF_HOOK include/linux/netfilter.h:289 [inline] ip6_input+0x2b6/0x350 net/ipv6/ip6_input.c:443 dst_input include/net/dst.h:450 [inline] ip6_rcv_finish+0x4e7/0x6d0 net/ipv6/ip6_input.c:76 NF_HOOK include/linux/netfilter.h:289 [inline] ipv6_rcv+0x34b/0x3f0 net/ipv6/ip6_input.c:272 __netif_receive_skb_one_core net/core/dev.c:4973 [inline] __netif_receive_skb net/core/dev.c:5083 [inline] process_backlog+0x756/0x10e0 net/core/dev.c:5923 napi_poll net/core/dev.c:6346 [inline] net_rx_action+0x78b/0x1a60 net/core/dev.c:6412 __do_softirq+0x53f/0x93a kernel/softirq.c:293 do_softirq_own_stack+0x49/0x80 arch/x86/entry/entry_64.S:1039 </IRQ> do_softirq kernel/softirq.c:338 [inline] __local_bh_enable_ip+0x16f/0x1a0 kernel/softirq.c:190 local_bh_enable+0x36/0x40 include/linux/bottom_half.h:32 rcu_read_unlock_bh include/linux/rcupdate.h:696 [inline] ip6_finish_output2+0x1d64/0x25f0 net/ipv6/ip6_output.c:121 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154 NF_HOOK_COND include/linux/netfilter.h:278 [inline] ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211 __do_sys_sendmmsg net/socket.c:2240 [inline] __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x457ec9 Code: 6d b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b b7 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007f4a5204fc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000457ec9 RDX: 00000000040001ab RSI: 0000000020000240 RDI: 0000000000000003 RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f4a520506d4 R13: 00000000004c4ce5 R14: 00000000004d85d8 R15: 00000000ffffffff Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:205 [inline] kmsan_internal_poison_shadow+0x92/0x150 mm/kmsan/kmsan.c:159 kmsan_kmalloc+0xa6/0x130 mm/kmsan/kmsan_hooks.c:176 kmsan_slab_alloc+0xe/0x10 mm/kmsan/kmsan_hooks.c:185 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2754 [inline] __kmalloc_node_track_caller+0xe9e/0xff0 mm/slub.c:4377 __kmalloc_reserve net/core/skbuff.c:140 [inline] __alloc_skb+0x309/0xa20 net/core/skbuff.c:208 alloc_skb include/linux/skbuff.h:1012 [inline] alloc_skb_with_frags+0x1c7/0xac0 net/core/skbuff.c:5288 sock_alloc_send_pskb+0xafd/0x10a0 net/core/sock.c:2091 sock_alloc_send_skb+0xca/0xe0 net/core/sock.c:2108 __ip6_append_data+0x42ed/0x5dc0 net/ipv6/ip6_output.c:1443 ip6_append_data+0x3c2/0x650 net/ipv6/ip6_output.c:1619 icmp6_send+0x2f5c/0x3c40 net/ipv6/icmp.c:574 icmpv6_send+0xe5/0x110 net/ipv6/ip6_icmp.c:43 ip6_link_failure+0x5c/0x2c0 net/ipv6/route.c:2231 dst_link_failure include/net/dst.h:427 [inline] vti_xmit net/ipv4/ip_vti.c:229 [inline] vti_tunnel_xmit+0xf3b/0x1ea0 net/ipv4/ip_vti.c:265 __netdev_start_xmit include/linux/netdevice.h:4382 [inline] netdev_start_xmit include/linux/netdevice.h:4391 [inline] xmit_one net/core/dev.c:3278 [inline] dev_hard_start_xmit+0x604/0xc40 net/core/dev.c:3294 __dev_queue_xmit+0x2e48/0x3b80 net/core/dev.c:3864 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3897 neigh_direct_output+0x42/0x50 net/core/neighbour.c:1511 neigh_output include/net/neighbour.h:508 [inline] ip6_finish_output2+0x1d4e/0x25f0 net/ipv6/ip6_output.c:120 ip6_finish_output+0xae4/0xbc0 net/ipv6/ip6_output.c:154 NF_HOOK_COND include/linux/netfilter.h:278 [inline] ip6_output+0x5ca/0x710 net/ipv6/ip6_output.c:171 dst_output include/net/dst.h:444 [inline] ip6_local_out+0x164/0x1d0 net/ipv6/output_core.c:176 ip6_send_skb+0xfa/0x390 net/ipv6/ip6_output.c:1727 udp_v6_send_skb+0x1733/0x1d20 net/ipv6/udp.c:1169 udpv6_sendmsg+0x424e/0x45d0 net/ipv6/udp.c:1466 inet_sendmsg+0x54a/0x720 net/ipv4/af_inet.c:798 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmmsg+0x580/0xad0 net/socket.c:2211 __do_sys_sendmmsg net/socket.c:2240 [inline] __se_sys_sendmmsg+0xbd/0xe0 net/socket.c:2237 __x64_sys_sendmmsg+0x56/0x70 net/socket.c:2237 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 Fixes: b8a51b38 ("fou, fou6: ICMP error handlers for FoU and GUE") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Cc: Stefano Brivio <sbrivio@redhat.com> Cc: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Davide Caratti authored
After commit 1c25324c ("net/sched: act_tunnel_key: Don't dump dst port if it wasn't set"), act_tunnel_key doesn't dump anymore the destination port, unless it was explicitly configured. This caused systematic failures in the following TDC test case: 7a88 - Add tunnel_key action with cookie parameter Avoid matching zero values of TCA_TUNNEL_KEY_ENC_DST_PORT to let the test pass again. Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Davide Caratti authored
After merge of commit 80ef0f22 ("net/sched: act_tunnel_key: Allow key-less tunnels"), act_tunnel_key does not reject anymore requests to install 'set' rules where the key id is missing. Therefore, drop the following TDC testcase: ba4e - Add tunnel_key set action with missing mandatory id parameter because it's going to become a systematic fail as soon as userspace iproute2 will start supporting key-less tunnels. Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't take the lock again with phy_read(), use the unlocked __phy_read(). Fixes: 424ca4c5 ("net: phy: marvell: fix paged access races") Reported-by:
Åke Rehnman <ake.rehnman@gmail.com> Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrew Lunn authored
The VOD can be out of spec, unless some magic value is poked into an undocumented register in an undocumented page. Fixes: e4cf8a38 ("net: phy: Marvell: Add mv88e6390 internal PHY") Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Greg Kroah-Hartman authored
Commit 65cab850 ("net: Allow class-e address assignment via ifconfig ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too many '(' characters were added to the line, making any code that used it, not build properly. Also, the macro now compares an unsigned with a signed value, which isn't ok, so fix that up by making both types match properly. Reported-by:
Christopher Ferris <cferris@google.com> Fixes: 65cab850 ("net: Allow class-e address assignment via ifconfig ioctl") Cc: Dave Taht <dave.taht@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Willem de Bruijn authored
TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of the connection and so transitions this socket to CLOSE_WAIT state. Transmission in close wait state is acceptable. Other similar tests in the stack (e.g., in FastOpen) accept both states. Relax this test, too. Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html Fixes: f214f915 ("tcp: enable MSG_ZEROCOPY") Reported-by:
Marek Majkowski <marek@cloudflare.com> Signed-off-by:
Willem de Bruijn <willemb@google.com> CC: Yuchung Cheng <ycheng@google.com> CC: Neal Cardwell <ncardwell@google.com> CC: Soheil Hassas Yeganeh <soheil@google.com> CC: Alexey Kodanev <alexey.kodanev@oracle.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
So far genphy_soft_reset was used automatically if the PHY driver didn't implement the soft_reset callback. This changed with the mentioned commit and broke KSZ9031. To fix this configure the KSZ9031 PHY driver to use genphy_soft_reset. Fixes: 6e2d85ec ("net: phy: Stop with excessive soft reset") Reported-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Tested-by:
Tony Lindgren <tony@atomide.com> Tested-by:
Sekhar Nori <nsekhar@ti.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Davide Caratti authored
running the following TDC test cases: 7afc - Replace tunnel_key set action with all parameters 364d - Replace tunnel_key set action with all parameters and cookie it's possible to trigger kmemleak warnings like: unreferenced object 0xffff94797127ab40 (size 192): comm "tc", pid 3248, jiffies 4300565293 (age 1006.862s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 c0 93 f9 8a ff ff ff ff ................ 41 84 ee 89 ff ff ff ff 00 00 00 00 00 00 00 00 A............... backtrace: [<000000001e85b61c>] tunnel_key_init+0x31d/0x820 [act_tunnel_key] [<000000007f3f6ee7>] tcf_action_init_1+0x384/0x4c0 [<00000000e89e3ded>] tcf_action_init+0x12b/0x1a0 [<00000000c1c8c0f8>] tcf_action_add+0x73/0x170 [<0000000095a9fc28>] tc_ctl_action+0x122/0x160 [<000000004bebeac5>] rtnetlink_rcv_msg+0x263/0x2d0 [<000000009fd862dd>] netlink_rcv_skb+0x4a/0x110 [<00000000b55199e7>] netlink_unicast+0x1a0/0x250 [<000000004996cd21>] netlink_sendmsg+0x2c1/0x3c0 [<000000004d6a94b4>] sock_sendmsg+0x36/0x40 [<000000005d9f0208>] ___sys_sendmsg+0x280/0x2f0 [<00000000dec19023>] __sys_sendmsg+0x5e/0xa0 [<000000004b82ac81>] do_syscall_64+0x5b/0x180 [<00000000a0f1209a>] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [<000000002926b2ab>] 0xffffffffffffffff when the tunnel_key action is replaced, the kernel forgets to release the dst metadata: ensure they are released by tunnel_key_init(), the same way it's done in tunnel_key_release(). Fixes: d0f6dd8a ("net/sched: Introduce act_tunnel_key") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Acked-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Howells authored
The changes introduced to allow rxrpc calls to be retried creates an issue when it comes to refcounting afs_call structs. The problem is that when rxrpc_send_data() queues the last packet for an asynchronous call, the following sequence can occur: (1) The notify_end_tx callback is invoked which causes the state in the afs_call to be changed from AFS_CALL_CL_REQUESTING or AFS_CALL_SV_REPLYING. (2) afs_deliver_to_call() can then process event notifications from rxrpc on the async_work queue. (3) Delivery of events, such as an abort from the server, can cause the afs_call state to be changed to AFS_CALL_COMPLETE on async_work. (4) For an asynchronous call, afs_process_async_call() notes that the call is complete and tried to clean up all the refs on async_work. (5) rxrpc_send_data() might return the amount of data transferred (success) or an error - which could in turn reflect a local error or a received error. Synchronising the clean up after rxrpc_kernel_send_data() returns an error with the asynchronous cleanup is then tricky to get right. Mostly revert commit c038a58c . The two API functions the original commit added aren't currently used. This makes rxrpc_kernel_send_data() always return successfully if it queued the data it was given. Note that this doesn't affect synchronous calls since their Rx notification function merely pokes a wait queue and does not refcounting. The asynchronous call notification function *has* to do refcounting and pass a ref over the work item to avoid the need to sync the workqueue in call cleanup. Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Ying Xue says: ==================== tipc: fix uninit-value issues reported by syzbot Recently, syzbot complained that TIPC module exits several issues associated with uninit-value type. So, in this series, we try to fix them as many as possible. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ying Xue authored
BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335 CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:53 kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683 tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335 tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153 genl_family_rcv_msg net/netlink/genetlink.c:599 [inline] genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624 netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447 genl_rcv+0x63/0x80 net/netlink/genetlink.c:635 netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline] netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337 netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmsg net/socket.c:2080 [inline] SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091 SyS_sendmsg+0x54/0x80 net/socket.c:2087 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 RIP: 0033:0x43fda9 RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9 RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8 R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0 R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314 kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321 slab_post_alloc_hook mm/slab.h:445 [inline] slab_alloc_node mm/slub.c:2737 [inline] __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:984 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline] netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmsg net/socket.c:2080 [inline] SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091 SyS_sendmsg+0x54/0x80 net/socket.c:2087 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 In tipc_nl_compat_recv(), when the len variable returned by nlmsg_attrlen() is 0, the message is still treated as a valid one, which is obviously unresonable. When len is zero, it means the message not only doesn't contain any valid TLV payload, but also TLV header is not included. Under this stituation, tlv_type field in TLV header is still accessed in tipc_nl_compat_dumpit() or tipc_nl_compat_doit(), but the field space is obviously illegal. Of course, it is not initialized. Reported-by:
<syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com> Reported-by:
<syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com> Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ying Xue authored
syzbot reported: BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline] BUG: KMSAN: uninit-value in tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826 CPU: 0 PID: 6290 Comm: syz-executor848 Not tainted 4.19.0-rc8+ #70 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x306/0x460 lib/dump_stack.c:113 kmsan_report+0x1a2/0x2e0 mm/kmsan/kmsan.c:917 __msan_warning+0x7c/0xe0 mm/kmsan/kmsan_instr.c:500 __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline] __fswab32 include/uapi/linux/swab.h:59 [inline] tipc_nl_compat_name_table_dump+0x4a8/0xba0 net/tipc/netlink_compat.c:826 __tipc_nl_compat_dumpit+0x59e/0xdb0 net/tipc/netlink_compat.c:205 tipc_nl_compat_dumpit+0x63a/0x820 net/tipc/netlink_compat.c:270 tipc_nl_compat_handle net/tipc/netlink_compat.c:1151 [inline] tipc_nl_compat_recv+0x1402/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185c/0x1a20 net/netlink/genetlink.c:626 netlink_rcv_skb+0x394/0x640 net/netlink/af_netlink.c:2454 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline] netlink_unicast+0x166d/0x1720 net/netlink/af_netlink.c:1343 netlink_sendmsg+0x1391/0x1420 net/netlink/af_netlink.c:1908 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 RIP: 0033:0x440179 Code: 18 89 d0 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 fb 13 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffecec49318 EFLAGS: 00000213 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 0000000000440179 RDX: 0000000000000000 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006ca018 R08: 0000000000000000 R09: 00000000004002c8 R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000401a00 R13: 0000000000401a90 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:255 [inline] kmsan_internal_poison_shadow+0xc8/0x1d0 mm/kmsan/kmsan.c:180 kmsan_kmalloc+0xa4/0x120 mm/kmsan/kmsan_hooks.c:104 kmsan_slab_alloc+0x10/0x20 mm/kmsan/kmsan_hooks.c:113 slab_post_alloc_hook mm/slab.h:446 [inline] slab_alloc_node mm/slub.c:2727 [inline] __kmalloc_node_track_caller+0xb43/0x1400 mm/slub.c:4360 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x422/0xe90 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:996 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1189 [inline] netlink_sendmsg+0xcaf/0x1420 net/netlink/af_netlink.c:1883 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xe47/0x1200 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x307/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbe/0x100 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 We cannot take for granted the thing that the length of data contained in TLV is longer than the size of struct tipc_name_table_query in tipc_nl_compat_name_table_dump(). Reported-by:
<syzbot+06e771a754829716a327@syzkaller.appspotmail.com> Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ying Xue authored
syzbot reports following splat: BUG: KMSAN: uninit-value in strlen+0x3b/0xa0 lib/string.c:486 CPU: 1 PID: 9306 Comm: syz-executor172 Not tainted 4.20.0-rc7+ #2 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x173/0x1d0 lib/dump_stack.c:113 kmsan_report+0x12e/0x2a0 mm/kmsan/kmsan.c:613 __msan_warning+0x82/0xf0 mm/kmsan/kmsan_instr.c:313 strlen+0x3b/0xa0 lib/string.c:486 nla_put_string include/net/netlink.h:1154 [inline] __tipc_nl_compat_link_set net/tipc/netlink_compat.c:708 [inline] tipc_nl_compat_link_set+0x929/0x1220 net/tipc/netlink_compat.c:744 __tipc_nl_compat_doit net/tipc/netlink_compat.c:311 [inline] tipc_nl_compat_doit+0x3aa/0xaf0 net/tipc/netlink_compat.c:344 tipc_nl_compat_handle net/tipc/netlink_compat.c:1107 [inline] tipc_nl_compat_recv+0x14d7/0x2760 net/tipc/netlink_compat.c:1210 genl_family_rcv_msg net/netlink/genetlink.c:601 [inline] genl_rcv_msg+0x185f/0x1a60 net/netlink/genetlink.c:626 netlink_rcv_skb+0x444/0x640 net/netlink/af_netlink.c:2477 genl_rcv+0x63/0x80 net/netlink/genetlink.c:637 netlink_unicast_kernel net/netlink/af_netlink.c:1310 [inline] netlink_unicast+0xf40/0x1020 net/netlink/af_netlink.c:1336 netlink_sendmsg+0x127f/0x1300 net/netlink/af_netlink.c:1917 sock_sendmsg_nosec net/socket.c:621 [inline] sock_sendmsg net/socket.c:631 [inline] ___sys_sendmsg+0xdb9/0x11b0 net/socket.c:2116 __sys_sendmsg net/socket.c:2154 [inline] __do_sys_sendmsg net/socket.c:2163 [inline] __se_sys_sendmsg+0x305/0x460 net/socket.c:2161 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2161 do_syscall_64+0xbc/0xf0 arch/x86/entry/common.c:291 entry_SYSCALL_64_after_hwframe+0x63/0xe7 The uninitialised access happened in nla_put_string(skb, TIPC_NLA_LINK_NAME, lc->name) This is because lc->name string is not validated before it's used. Reported-by:
<syzbot+d78b8a29241a195aefb8@syzkaller.appspotmail.com> Signed-off-by:
Ying Xue <ying.xue@windriver.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-