This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Some basic debugfs support to dump the IP registers. Further
statistics could easily be added in the future for example for
each enabled tsin channel we could expose number of corrupt packets
received etc.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the following 2 NIM cards: -
1) B2100A (2x stv0367 demods & 2x NXP tda18212 tuners)
2) STV0903-6110NIM (stv0903 demod + 6110 tuner, lnb24)

A NIM card is a cold plugable expansion card which usually
features a demodulator / tuner combination.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

These functions are used by the core code for creating the LDVB
devices and adapter.

Addtionally some older SoC's (and potentially newer ones) have different
frontend HW which would allow those devices to be easily supported
in the future by keeping the code specific to the IP separate from the
more generic code.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds support for the c8sectpfe input HW found on
STiH407/410 SoC's.

It currently supports the TS input block, memdma engine
and hw PID filtering blocks of the C8SECTPFE subsystem.

The driver creates one LinuxDVB adapter, and a
demux/dvr/frontend set of devices for each tsin channel
which is specificed in the DT. It has been tested with
multiple tsin channels tuned, locked, and grabbing TS
simultaneously.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds in the required DT node for the c8sectpfe
Linux DVB demux driver which allows the tsin channels
to be used on an upstream kernel.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch adds the DT bindings documentation for the c8sectpfe LinuxDVB
demux driver whose IP is in the STiH407 family silicon SoC's.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Convert the struct dvb_pll_desc uses to const and
change the "entries" fixed array size from 12 to []

It saves a couple KB overall and remove ~5KB of data.

$ size drivers/media/dvb-frontends/dvb-pll.o*
   text        data     bss     dec     hex filename
   8520        1552    2120   12192    2fa0 drivers/media/dvb-frontends/dvb-pll.o.new
   5624        6363    2120   14107    371b drivers/media/dvb-frontends/dvb-pll.o.old

[PG] Patch taken from https://lkml.org/lkml/2015/6/24/721

 with
commit message updated.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Michael Ira Krufky <m.krufky@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The B2100A dvb NIM card from ST has 2x stv0367 demodulators
and 2x TDA18212 silicon tuners, with a 16Mhz crystal. To
get this working properly with the upstream driver we need
to add support for the 16Mhz reference clock.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

When using stv0367 demodulator with STi STB platforms,
we can have easily have four or more stv0367 demods running
in the system at one time.

As typically the b2120 reference design ships with a b2004a daughter
board, which can accept two dvb NIM cards, and each b2100A NIM
has 2x stv0367 demods and 2x NXPs tuner on it.

In such circumstances it is useful to print the i2c address
on error messages to know which one is failing due to I2C issues.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
        drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.

The max usecase of the driver seems to be 10 bytes + 1 for the
register.

So, let's be safe and allocate 11 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
	drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.

The max usecase of the driver seems to be 5 bytes + 1 for the
register.

So, let's be safe and allocate 6 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:

	drivers/media/dvb-frontends/cxd2841er.c:205:19: warning: Variable length array is used.

The max usecase of the driver seems to be 15 bytes + 1 for the
register.

So, let's be safe and allocate 17 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add NetUP Dual Universal CI PCIe board driver.
The board has
    - two CI slots
    - two I2C adapters
    - SPI master bus for accessing flash memory containing
      FPGA firmware

No changes required.

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

drivers/media/dvb-frontends/cxd2841er.c:992:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_t2' [-Wmissing-prototypes]
 int cxd2841er_get_carrier_offset_t2(
     ^
drivers/media/dvb-frontends/cxd2841er.c:1032:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_c' [-Wmissing-prototypes]
 int cxd2841er_get_carrier_offset_c(
     ^
drivers/media/dvb-frontends/cxd2841er.c:1360:5: warning: no previous prototype for 'cxd2841er_read_snr_t2' [-Wmissing-prototypes]
 int cxd2841er_read_snr_t2(struct cxd2841er_priv *priv, u32 *snr)
     ^

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add DVB-C/T/T2/S/S2 demodulator frontend driver Sony CXD2841ER chip.

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add DVB SEC frontend driver for STM LNBH25PQR chip.

[mchehab@osg.samsung.com: fix merge conflict:
 fe_sec_voltage_t should not be used in kernelspace anymore.
 instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add DVB-T/T2/C frontend driver for Sony Ascot2e (CXD2861ER) chip.

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add DVB-S/S2 frontend driver for Sony Horus3A (CXD2832AER) chip

Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Using 8 URBs results in a consecutive buffer allocation of too much
memory for some arm devices.
As we use isochronuous transfers the number of URBs can be reduced
without risking data-loss.

Signed-off-by: Christian Loepke <loepke@edfritsch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Commit 275ddb40

 removed the lirc
"protocol" but kept backwards compatibility by always listing
the protocol as present and enabled. This patch further improves
the logic by only listing the protocol if the lirc module is loaded
(or if lirc is builtin).

Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

platform_driver does not need to set an owner because
platform_driver_register() will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Note that the 6 in the third argument of memset appears to represent
an ethernet address size (ETH_ALEN).

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@eth_zero_addr@
expression e;
@@

-memset(e,0x00,6);
+eth_zero_addr(e);
// </smpl>

Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Make the TV tuners menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.

Without this, many drivers stay disabled during e.g. allmodconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Note that the 6 in the third argument of memset appears to represent
an ethernet address size (ETH_ALEN).

The Coccinelle semantic patch that makes this change is as follows:

// <smpl>
@eth_zero_addr@
expression e;
@@

-memset(e,0x00,6);
+eth_zero_addr(e);
// </smpl>

Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This patch removes unneded goto,
reported by coccinelle.

Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Reviewed-by: Akhilesh Kumar <akhilesh.k@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Make the i2c devices menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.

Without this, many drivers stay disabled during e.g. allmodconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Make the DVB Frontends menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.

Without this, many drivers stay disabled during e.g. allmodconfig.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

On built-in kernels this warning will always splat as this is part
of the module init. Fix that by shifting the PAT requirement check
out under the code that does the "quasi-probe" for the device. This
device driver relies on an existing driver to find its own devices,
it looks for that device driver and its own found devices, then
uses driver_for_each_device() to try to see if it can probe each of
those devices as a frambuffer device with ivtvfb_init_card(). We
tuck the PAT requiremenet check then on the ivtvfb_init_card()
call making the check at least require an ivtv device present
before complaining.

Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.

Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

I noticed certain cards are currently under MEDIA_ANALOG_TV_SUPPORT
but it seems they are frame grabbers (with CVBS, Svideo etc. inputs)
rather than TV receivers (with analog TV tuners).

MEDIA_CAMERA_SUPPORT maybe isn't the best name (only "meye" driver seems
to drive a real camera in a laptop) but it at least doesn't select the
TUNERs.

Perhaps the following patch would make sense.

Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Gotos makes a little harder to check the code. In this
particular case, the goto is doing nothing but jumping into
a return.

Instead, just replace the goto by the return, making it
simpler.

Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>