Marvell has now provided bootloaders that are Device Tree capable for
the Armada XP DB board, and that also remap the internal register base
address to 0xf1000000. In addition, the bootloader now sets the MBus
Window base address to 0xf0000000, but on this board, this change
doesn't make much difference since the board is by default equipped
with 2 GB of RAM.

Therefore this commit updates the soc->ranges Device Tree property
with the fact that the internal registers are now mapped at
0xf1000000.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The latest Marvell bootloaders for various boards change the MBus
Window base address from 0xC0000000 to 0xF0000000, in order to make
more RAM in the first 4 GB actually usable by the kernel (RAM that is
covered by the MBus window is "shadowed" and therefore not usable).

However, our default PCIe memory and I/O apertures where sitting at
0xe0000000 (for memory) and 0xe8000000 (for I/O), which will now be
outside of the MBus Window range on those platforms. To make things
work, we have to ensure those apertures use addresses in the
0xF0000000 -> 0xFFFFFFFF range.

Of course this change of the MBus Window base address from 0xC0000000
to 0xF0000000 also comes with a change of the internal register base
address from 0xD0000000 to 0xF1000000.

We have therefore designed the following memory map:

 * 0xF0000000 -> 0xF1000000: 16 MB, used for NOR flashes on Armada XP
   GP and Armada XP DB.

 * 0xF1000000 -> 0xF1100000: 1 MB, used for internal registers.

 * 0xF8000000 -> 0xFFE00000: 126 MB, used for PCIe memory.

 * 0xFFE00000 -> 0xFFF00000: 1 MB, used for PCIe I/O.

 * 0xFFF00000 -> 0xFFFFFFFF: 1 MB, used for the BootROM mapping

There is one exception to this layout: the Armada XP OpenBlocks, which
has a 128 MB NOR flash, mapped from 0xF0000000 to 0xF8000000. This
does not conflict with the current change for the PCIe I/O and memory
apertures, and continues to work because on Armada XP OpenBlocks, the
bootloader is an old one, and continues to have internal registers
mapped at 0xD0000000.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This adds a DT node for the system-controller found on Marvell Dove
SoCs.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Describe the T5325 using device tree properties, where possible.  The
first version of this file was produced by Thomas Petazzoni.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

When using platform_driver instantiation, the i2c bus was given bus
number 0. The kirkwood-t5325 audio driver has this bus number hard
coded for the address of the codec. However by default device tree i2c
busses are dynamically allocated a bus number, starting from 1. Thus
the kirkwood-t5325 cannot find its audio codec. By adding an alias in
the DT file we can control the bus number and set it to 0. The codec
can then be found.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The binding has existed for a while, so add the missing node so it can
be used by devices.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

With kirkwood migrating into mach-mvebu, mvebu_v5_defconfig needs to
select ARCH_MVEBU.  Unfortunately, this means that when building a v5
kernel, we unnecessarily build dtbs for the armada v7 boards.

To fix this, we instead select based on MACH_ARMADA_* on a per SoC basis.

Reported-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

We share global config registers by syscon node, add it to dove.dtsi.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Dove pinctrl uses additional registers to control MPPs. This patch first
increases existing pinctrl reg property by one register, and then adds
two new ranges for MPP4 and PMU MPP registers.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Make use of the mvebu system controller, by placing a node into the
dtsi file.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Now that the Feroceon L2 cache has a DT binding, make use of it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

mvebu dt fixes for v3.14

 - mvebu: add missing 'eth3' alias for mv78260

 - dove: revert PMU interrupt controller node, wait for driver to land.

Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 375 and Armada 38x Device Tree files.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Instead of hardcoding 0 and 1 to indicate SPI and PPI GIC interrupts,
use the definitions of <dt-bindings/interrupt-controller/arm-gic.h> to
clarify the Device Tree code.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Some of the Armada 375/38x DTs that were recently submitted were still
using the old-style /include/ instead of the new-style, C-preprocessor
based #include. Since we are going to start including more headers,
switching to the C-preprocessor based includes is important.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add device tree fragments and files to support many of the kirkwood
based Synology NAS devices. This is a modification of
Andrew Lunn's <andrew@lunn.ch> translation of the board setup file
maintained by Ben Peddell <klightspeed@killerwolves.net>

The Ricoh RS5C372 RTC was used in all 2009 units and some 2010 units.
All other Synology Kirkwood-based DiskStations and RackStations use
the Seiko S35390A RTC.

Most of the 1-bay and 2-bay units use the GPIOs that are multiplexed
with the built-in SATA interface activity/presence pins on mpp 20-23,
while the 4-bay units use ge01 and a PCIe SATA controller, and put the
software controlled HDD leds on mpp 36-43.

Most of the 6281 units with HDD power controls use mpp 29 and 31, while
most of the 6282 units with HDD power controls use mpp 30, 34, 44 and 45
and provide a model ID on mpp 28, 29, 46 and 47.  Pre-2012 units and
most 4-bay units didn't have a separate power control for HDD1.  These
power controls are presumably to limit startup current from the 12V
brick power supply.

Instead of using separate dtsi files in a synology directory, this
patch uses a single dtsi file containing all of the modules for
these boards, with all of the modules not common to all boards
disabled.  The board dts files then enable the appropriate modules for
their boards.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Tested-by: Ben Peddell <klightspeed@killerwolves.net> (ds211j)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add the Seiko Instruments Inc S35390a to the list of trivial i2c
devices.

Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The following patches make use of vendor names:
* ricoh (Ricoh Co. Ltd.);
* qnap (QNAP Systems, Inc.);
* sii (Seiko Instruments, Inc.); and
* synology (Synology, Inc.)

Add them to the vendor prefix list.

Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The corresponding driver didn't make it into v3.14, so we need to remove
the node.  Dove systems fail to boot with the node present and no
driver.

This node will be re-added when the driver makes it to mainline.

Reported-by: Jean-Francois Moine <moinejf@free.fr>
Tested-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 385 DB board is the development board from Marvell for the
Armada 385 SoC. This commit adds a Device Tree description for this
board, which enables the following features:

 * Network interfaces
 * I2C buses
 * SDIO
 * Serial port
 * SPI bus, with a SPI flash
 * PCIe interfaces

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 380 and 385 SoCs are new SoCs from Marvell, based on a
Cortex-A9 cores (single core for 380, dual core for 385) and a number
of hardware blocks that are common with earlier SoCs from the mvebu
family.

The provided Device Tree describes the following parts of the SoC:

 * CPU
 * Device Bus
 * Clocks
 * Interrupt controllers: GIC and MPIC
 * GPIO controllers
 * I2C buses
 * L2 cache
 * MBus controller
 * Pinctrl
 * Serial
 * SPI buses
 * System controller (for reboot)
 * Timer
 * XOR engines
 * PCIe controllers
 * Network interfaces

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 375 DB board is the development board from Marvell for the
Armada 375 SoC. This commit adds a Device Tree description for this
board, which enables the following features:

 * I2C buses
 * SDIO
 * Serial port
 * SPI bus, with a SPI flash. Note that the SPI bus is disabled by
   default, because it conflicts with the NAND, and can only work if
   the board boots out of SPI. Since most boards are shipped to boot
   out of NAND, we're default to having the SPI bus disabled.
 * PCIe interfaces

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 375 SoC is a new SoC from Marvell, based on a dual core
Cortex-A9 and a number of hardware blocks that are common with earlier
SoCs from the mvebu family.

The provided Device Tree describes the following parts of the SoC:

 * CPUs
 * Device Bus
 * Clocks
 * Interrupt controllers: GIC and MPIC
 * GPIO controllers
 * I2C buses
 * L2 cache
 * MBus controller
 * SDIO
 * Pinctrl
 * SATA
 * Serial
 * SPI buses
 * System controller (for reboot)
 * Timer
 * XOR engines
 * PCIe controllers

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add the devicetree node to enable watchdog support available in Dove SoCs.

Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

In order to support multiplatform builds the watchdog devicetree binding
was modified and now the 'reg' property is specified to need two
entries. This commit adds the second entry as-per the new specification.

Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add the DT nodes to enable watchdog support available in Armada 370
and Armada XP SoCs.

Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Perform a mechanical translation of rd88f6281-setup.c into DT.  Since
the hardware differs between the A0 and A1 stepping, two dts files are
used, and a .dtsi file for the common parts. The A0 part does not have
a "wan" port on the switch and uses PHY address 10 to address the
switch. The A1 part does have the "wan" port and uses address 0.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Mechanically translate rd88f6192-nas-setup.c into DT equivelent.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

In addition to the analog audio input and output, the Armada 370 DB
also has S/PDIF input and output optical connectors. This commit
improves the Device Tree description of the Armada 370 DB platform to
enable the S/PDIF support.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This commit adds the necessary Device Tree informations to enable
audio support on the Armada 370 DB platform. In details it:

 * Instantiates the CS42L51 audio codec on the I2C0 bus, and
   configures this bus with the appropriate pin-muxing configuration.

 * Enables the I2S audio controller, and configures it with the
   appropriate pin-muxing configuration.

 * Through hog pins, ensures that the other pins possibly used for I2S
   are muxed with another function than I2S.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This commit adds a pin-muxing configuration for the I2C0 bus of the
Armada 370, which is used on the Armada 370 DB platform to interface
with the CS42L51 audio codec.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 370 SoC has an I2S audio controller. This commit adds the
description of this controller to the Device Tree describing this SoC,
as well as two possible muxing configurations for the I2S bus pins.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Instead of harcoding keycodes specifications in the Armada 370/XP
boards, use the <dt-bindings/input/input.h> header file and its
keycode definitions.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Instead of harcoding 0 and 1 for the gpio specifications in the Armada
370/XP boards, use the <dt-bindings/gpio/gpio.h> header file and its
GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW definitions.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

It was correctly set on mv78460 but not on mv78260, resulting in my
OpenBlocks AX3-4 retrieving only 3 of its 4 MAC addresses from the
boot loader.

Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Re-implement the Marvell Kirkwood ts41x-setup.c in DT.

As with the QNAP 119, there are two variants, depending on which SoC
has been used. They differ on Ethernet PHY addresses and number of
PCIe busses.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ian Campbell <ijc@hellion.org.uk> (kirkwood-ts419-6281.dtb)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Excito Bubba B3 is a home server, single drive NAS box, Wifi
access point, etc.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Pull parisc updates from Helge Deller:
 "The three major changes in this patchset is a implementation for
  flexible userspace memory maps, cache-flushing fixes (again), and a
  long-discussed ABI change to make EWOULDBLOCK the same value as
  EAGAIN.

  parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
  to keep HP-UX compatibility.  Since we will probably never implement
  full HP-UX support, we prefer to drop this compatibility to make it
  easier for us with Linux userspace programs which mostly never checked
  for both values.  We don't expect major fall-outs because of this
  change, and if we face some, we will simply rebuild the necessary
  applications in the debian archives"

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts