- Feb 09, 2014
-
-
Nicolin Chen authored
We must specify the value of audmux pinctrl if we want to use pinctrl_pm(). Thus change bypass value 0x80000000 to what we exactly need. This patch also seperately unset PUE bit for TXD so that IOMUX won't pull up/down the pin after turning into tristate. When we use SSI normal mode to playback monaural audio via I2S signal, there'd be a pulled curve occur to its signal at the second slot if setting PUE bit for TXD. And it will make the second channel to play a constant noise. So by keeping the signal level in the second slot, we can get a constant high level signal (-1) or a low level one (0). Signed-off-by:
Nicolin Chen <b42378@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Fabio Estevam authored
MX6QDL_PAD_EIM_D23__GPIO3_IO23 appears twice in the hog pin group. Remove one of the occurrences. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Fabio Estevam authored
Add Ethernet support for imx6q udoo board. Tested by booting a kernel via NFS. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Silvio F authored
Signed-off-by:
Silvio F <silvio.fricke@gmail.com> Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Silvio F authored
Signed-off-by:
Silvio F <silvio.fricke@gmail.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
The device tree specification recommends that generic name should be used for nodes. So instead of naming those fixed regulator nodes arbitrarily, let's use the generic name 'regulator@num' for those nodes. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that boards that share the same pinctrl setting do not have to define it time and time again in <board>.dts. However, along with the devices and use cases being added continuously, the pinctrl setting nodes under iomuxc becomes more than expected. This bloats device tree blob for particular board unnecessarily since only a small subset of those pinctrl setting nodes will be used by the board. It impacts not only the DTB file size but also the run-time device tree lookup efficiency. The patch moves all the pinctrl data into individual boards as needed. With the changes, the pinctrl setting nodes becomes local to particular board, and it makes no sense to continue numbering the setting for given peripheral. Thus, all the pinctrl phandler name gets updated to have only peripheral name in there. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Shawn Guo authored
Currently, all pinctrl setting nodes are defined in <soc>.dtsi, so that boards that share the same pinctrl setting do not have to define it time and time again in <board>.dts. However, along with the devices and use cases being added continuously, the pinctrl setting nodes under iomuxc becomes more than expected. This bloats device tree blob for particular board unnecessarily since only a small subset of those pinctrl setting nodes will be used by the board. It impacts not only the DTB file size but also the run-time device tree lookup efficiency. The patch moves all the pinctrl data into individual boards as needed. With the changes, the pinctrl setting nodes becomes local to particular board, and it makes no sense to continue numbering the setting for given peripheral. Thus, all the pinctrl phandler name gets updated to have only peripheral name in there. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Valentin Raevsky authored
Add initial support for cm-fx6 module. cm-fx6 is a module based on mx6q SoC with the following features: - Up to 4GB of DDR3 - 1 LCD/DVI output port - 1 HDMI output port - 2 LVDS LCD ports - Gigabit Ethernet - Analog Audio - CAN - SATA - NAND - PCIE This patch allows to boot up the module, configures the serial console, the Ethernet adapter and the heartbeat led. cm-fx6 is embedded inside the Utilite computer. Signed-off-by:
Valentin Raevsky <valentin@compulab.co.il> Signed-off-by:
Igor Grinberg <grinberg@compulab.co.il> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Peter Chen authored
Enable USB OTG controller at imx6q-arm2 board Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Tim Harvey authored
The Gateworks Ventana product family consists of several baseboard designs based on the Freescale i.MX6 family of processors. Each baseboard has a different set of possible features. Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Tim Harvey authored
Typically nodes are disabled by default and enabled when needed. Signed-off-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
- Feb 03, 2014
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linuxLinus Torvalds authored
Pull parisc updates from Helge Deller: "The three major changes in this patchset is a implementation for flexible userspace memory maps, cache-flushing fixes (again), and a long-discussed ABI change to make EWOULDBLOCK the same value as EAGAIN. parisc has been the only platform where we had EWOULDBLOCK != EAGAIN to keep HP-UX compatibility. Since we will probably never implement full HP-UX support, we prefer to drop this compatibility to make it easier for us with Linux userspace programs which mostly never checked for both values. We don't expect major fall-outs because of this change, and if we face some, we will simply rebuild the necessary applications in the debian archives" * 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: parisc: add flexible mmap memory layout support parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc parisc: convert uapi/asm/stat.h to use native types only parisc: wire up sched_setattr and sched_getattr parisc: fix cache-flushing parisc/sti_console: prefer Linux fonts over built-in ROM fonts
-
Mikulas Patocka authored
HPFS needs to load 4 consecutive 512-byte sectors when accessing the directory nodes or bitmaps. We can't switch to 2048-byte block size because files are allocated in the units of 512-byte sectors. Previously, the driver would allocate a 2048-byte area using kmalloc, copy the data from four buffers to this area and eventually copy them back if they were modified. In the current implementation of the buffer cache, buffers are allocated in the pagecache. That means that 4 consecutive 512-byte buffers are stored in consecutive areas in the kernel address space. So, we don't need to allocate extra memory and copy the content of the buffers there. This patch optimizes the code to avoid copying the buffers. It checks if the four buffers are stored in contiguous memory - if they are not, it falls back to allocating a 2048-byte area and copying data there. Signed-off-by:
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Mikulas Patocka authored
Previously, hpfs scanned all bitmaps each time the user asked for free space using statfs. This patch changes it so that hpfs scans the bitmaps only once, remembes the free space and on next invocation of statfs it returns the value instantly. New versions of wine are hammering on the statfs syscall very heavily, making some games unplayable when they're stored on hpfs, with load times in minutes. This should be backported to the stable kernels because it fixes user-visible problem (excessive level load times in wine). Signed-off-by:
Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz> Cc: stable@vger.kernel.org Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Helge Deller authored
Add support for the flexible mmap memory layout (as described in http://lwn.net/Articles/91829). This is especially very interesting on parisc since we currently only support 32bit userspace (even with a 64bit Linux kernel). Signed-off-by:
Helge Deller <deller@gmx.de>
-
Guy Martin authored
On Linux, only parisc uses a different value for EWOULDBLOCK which causes a lot of troubles for applications not checking for both values. Since the hpux compat is long dead, make EWOULDBLOCK behave the same as all other architectures. Signed-off-by:
Guy Martin <gmsoft@tuxicoman.be> Signed-off-by:
Helge Deller <deller@gmx.de>
-
Helge Deller authored
The stat.h header file is exported to userspace. Some userspace applications failed to compile due to missing/unknown types, so we better convert it to use native types only (like it's done on other architectures too). Signed-off-by:
Helge Deller <deller@gmx.de>
-
Helge Deller authored
Signed-off-by:
Helge Deller <deller@gmx.de>
-
Helge Deller authored
This commit: f8dae006 : parisc: Ensure full cache coherency for kmap/kunmap caused negative caching side-effects, e.g. hanging processes with expect and too many inequivalent alias messages from flush_dcache_page() on Debian 5 systems. This patch now partly reverts it and has been in production use on our debian buildd makeservers since a week without any major problems. Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # v3.9+ Signed-off-by:
Helge Deller <deller@gmx.de>
-
Helge Deller authored
The built-in ROM fonts lack many necessary ASCII characters, which is why it makes sens to prefer the Linux fonts instead if they are available. This makes consoles on STI graphics cards which are not supported by the stifb driver (e.g. Visualize FXe) looks much nicer. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: stable@vger.kernel.org # v3.13
-
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/stagingLinus Torvalds authored
Pull hwmon kconfig fixes from Jean Delvare. * 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: hwmon: Fix SENSORS_TMP102 dependencies to eliminate build errors hwmon: Fix SENSORS_LM75 dependencies to eliminate build errors
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linuxLinus Torvalds authored
Pull SLAB changes from Pekka Enberg: "Random bug fixes that have accumulated in my inbox over the past few months" * 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: mm: Fix warning on make htmldocs caused by slab.c mm: slub: work around unneeded lockdep warning mm: sl[uo]b: fix misleading comments slub: Fix possible format string bug. slub: use lockdep_assert_held slub: Fix calculation of cpu slabs slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
-
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linuxLinus Torvalds authored
Pull turbostat updates from Len Brown. * 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: tools/power turbostat: introduce -s to dump counters tools/power turbostat: remove unused command line option turbostat: Add option to report joules consumed per sample turbostat: run on HSX turbostat: Add a .gitignore to ignore the compiled turbostat binary turbostat: Clean up error handling; disambiguate error messages; use err and errx turbostat: Factor out common function to open file and exit on failure turbostat: Add a helper to parse a single int out of a file turbostat: Check return value of fscanf turbostat: Use GCC's CPUID functions to support PIC turbostat: Don't attempt to printf an off_t with %zx turbostat: Don't put unprocessed uapi headers in the include path
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds authored
Pull ARM SoC fixes from Olof Johansson: "Here's a set of patches for (hopefully) -rc1. Some of them are fixes, but a good number of them also do things such as enable new drivers in the defconfigs for platforms that have such devices, increases coverage of the multiplatform defconfig and some DTS changes that plumbs up some of the devices that now have bindings and driver support. The commit dates are recent; we've mostly collected these fixes in the last few days but I also had to rebuild the branch yesterday to sort out some internal conflicts which reset the timestamps. The changes should have been tested by each platform maintainer already (and few of them have cross-platform impact) so I'm personally not too concerned by it at this time" * tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits) ARM: multi_v7_defconfig: remove redundant entries and re-enable TI_EDMA ARM: multi_v7_defconfig: add mvebu drivers clocksource: kona: Add basic use of external clock drivers: bus: fix CCI driver kcalloc call parameters swap ARM: dts: bcm28155-ap: Fix Card Detection GPIO ARM: multi_v7_defconfig: Select CONFIG_AT803X_PHY ARM: keystone: config: fix build warning when CONFIG_DMADEVICES is not set MAINTAINERS: ARM: SiRF: use regex patterns to involve all SiRF drivers ARM: dts: zynq: Add SDHCI nodes ARM: hisi: don't select SMP ARM: tegra: rebuild tegra_defconfig to add DEBUG_FS ARM: multi_v7: copy most options from tegra_defconfig ARM: iop32x: fix power off handling for the EM7210 board ARM: integrator: restore static map on the CP ARM: msm_defconfig: Enable MSM clock drivers ARM: dts: msm: Add clock controller nodes and hook into uart ARM: OMAP4+: move errata initialization to omap4_pm_init_early ARM: OMAP4460: cpuidle: Extend PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD on cpuidle ARM: mvebu: fix compilation warning on Armada 370 (i.e. non-SMP) ARM: shmobile: r8a7790.dtsi: ficx i2c[0-3] clock reference ...
-
Jean Delvare authored
Similar to what was done for the lm75 driver. Add depends on THERMAL since that is what provides the register/unregister functions above, but only if THERMAL_OF was selected as this is an optional feature of the driver. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by:
Eduardo Valentin <eduardo.valentin@ti.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net>
-
Jean Delvare authored
Based on an earlier attempt by Randy Dunlap. Fix SENSORS_LM75 dependencies to eliminate build errors: drivers/built-in.o: In function `lm75_remove': lm75.c:(.text+0x12bd8c): undefined reference to `thermal_zone_of_sensor_unregister' drivers/built-in.o: In function `lm75_probe': lm75.c:(.text+0x12c123): undefined reference to `thermal_zone_of_sensor_register' Add depends on THERMAL since that is what provides the register/unregister functions above, but only if THERMAL_OF was selected as this is an optional feature of the driver. Signed-off-by:
Jean Delvare <khali@linux-fr.org> Cc: Randy Dunlap <rdunlap@infradead.org> Acked-by:
Eduardo Valentin <eduardo.valentin@ti.com> Reviewed-by:
Guenter Roeck <linux@roeck-us.net>
-
- Feb 02, 2014
-
-
Andy Shevchenko authored
The new option allows just run turbostat and get dump of counter values. It's useful when we have something more than one program to test. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Len Brown <len.brown@intel.com>
-
Andy Shevchenko authored
The -s is not used, let's remove it, and update quick help accordingly. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Len Brown <len.brown@intel.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuildLinus Torvalds authored
Pull misc kbuild changes from Michal Marek: "The non-critical part of kbuild is small this time: - Three fixes for make deb-pkg - A new coccinelle check One of the deb-pkg fixes is a leftover from the last merge window, hence the merge commit" * 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: deb-pkg: Fix building for MIPS big-endian or ARM OABI deb-pkg: Fix cross-building linux-headers package scripts: Coccinelle script for pm_runtime_* return checks with IS_ERR_VALUE deb-pkg: Inhibit initramfs builders if CONFIG_BLK_DEV_INITRD is not set
-
Pali Rohár authored
Both proc files are writeable and used for configuring cells. But there is missing correct mode flag for writeable files. Without this patch both proc files are read only. [ It turns out they aren't really read-only, since root can write to them even if the write bit isn't set due to CAP_DAC_OVERRIDE ] Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Heiko Carstens authored
With commit d8d14bd0 ("fs/compat: fix lookup_dcookie() parameter handling") I changed the type of the len parameter of the lookup_dcookie() syscall. However I missed that there was still a stale declaration in arch/tile/.. which now causes a compile error on tile: In file included from fs/dcookies.c:28:0: include/linux/compat.h:425:17: error: conflicting types for 'compat_sys_lookup_dcookie' fs/dcookies.c:207:1: error: conflicting types for 'compat_sys_lookup_dcookie' Simply remove the declaration in the tile architecture, which is only a leftover from before the different compat lookup_dcookie() versions have been merged. The correct declaration is now in include/linux/compat.h The build error was reported by Fenguang's build bot. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Acked-by:
Chris Metcalf <cmetcalf@tilera.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "A set of cifs fixes (mostly for symlinks, and SMB2 xattrs) and cleanups" * 'for-linus' of git://git.samba.org/sfrench/cifs-2.6: cifs: Fix check for regular file in couldbe_mf_symlink() [CIFS] Fix SMB2 mounts so they don't try to set or get xattrs via cifs CIFS: Cleanup cifs open codepath CIFS: Remove extra indentation in cifs_sfu_type CIFS: Cleanup cifs_mknod CIFS: Cleanup CIFSSMBOpen cifs: Add support for follow_link on dfs shares under posix extensions cifs: move unix extension call to cifs_query_symlink() cifs: Re-order M-F Symlink code cifs: Add create MFSymlinks to protocol ops struct cifs: use protocol specific call for query_mf_symlink() cifs: Rename MF symlink function names cifs: Rename and cleanup open_query_close_cifs_symlink() cifs: Fix memory leak in cifs_hardlink()
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs fixes from Al Viro: "Several obvious fixes" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: Fix mountpoint reference leakage in linkat hfsplus: use xattr handlers for removexattr Typo in compat_sys_lseek() declaration fs/super.c: sync ro remount after blocking writers vfs: unexport the getname() symbol
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull rtl8812ae staging wireless driver from Greg KH: "Here's a single staging driver for a wireless chipset that has shown up in the SteamBox hardware. It is merged separately from the "main" staging pull request to sync up with the wireless api changes that came in from the networking tree. It's self-contained and works for me and others. Larry will be replacing it with a "real" driver for 3.15, but for now this one is needed" * tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: r8821ae: Enable build by reverting BROKEN marking staging: r8821ae: Fix build problems Staging: rtl8812ae: disable due to build errors Staging: rtl8821ae: add TODO file Staging: rtl8821ae: removed unused functions and variables Staging: rtl8821ae: rc.c: fix up function prototypes Staging: rtl8812ae: Add Realtek 8821 PCI WIFI driver
-
Rafael J. Wysocki authored
Revert commit ef83b078 "PCI: Remove from bus_list and release resources in pci_release_dev()" that made some nasty race conditions become possible. For example, if a Thunderbolt link is unplugged and then replugged immediately, the pci_release_dev() resulting from the hot-remove code path may be racing with the hot-add code path which after that commit causes various kinds of breakage to happen (up to and including a hard crash of the whole system). Moreover, the problem that commit ef83b078 attempted to address cannot happen any more after commit 8a4c5c32 "PCI: Check parent kobject in pci_destroy_dev()", because pci_destroy_dev() will now return immediately if it has already been executed for the given device. Note, however, that the invocation of msi_remove_pci_irq_vectors() removed by commit ef83b078 from pci_free_resources() along with the other changes made by it is not added back because of subsequent code changes depending on that modification. Fixes: ef83b078 (PCI: Remove from bus_list and release resources in pci_release_dev()) Reported-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
- Feb 01, 2014
-
-
Olof Johansson authored
TI_EDMA fell out of automatically selected options in the multi_v7 defconfig due to a select being removed from the davinci Kconfig entry. So we need to re-enable explicitly to not regress some platforms. The rest is just the result of running 'make multi_v7_defconfig + make savedefconfig' to remove entries that are no longer needed due to changed dependencies/selects or defaults. Signed-off-by:
Olof Johansson <olof@lixom.net>
-
Olof Johansson authored
Recent boot farm testing has highlighted some issues with mvebu and multiplatform kernels. Increase the test coverage so we can discover these issues earlier. Signed-off-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
Olof Johansson <olof@lixom.net>
-
Tim Kryger authored
When an clock is specified in the device tree, enable it and use it to determine the external clock frequency. Signed-off-by:
Tim Kryger <tim.kryger@linaro.org> Reviewed-by:
Markus Mayer <markus.mayer@linaro.org> Reviewed-by:
Matt Porter <matt.porter@linaro.org> Reviewed-by:
Christian Daudt <bcm@fixthebug.org> Acked-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
Christian Daudt <bcm@fixthebug.org> Signed-off-by:
Olof Johansson <olof@lixom.net>
-