Merge tag 'ux500-dt-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

A set of device tree-related cleanups for the ux500 platform from Linus
Walleij:

- Rename SSP/SPI clocks to the name found in the hardware
  reference manual. (Also includes a rename in the U300
  device tree file.)
- Delete dead non-DT code.
- Drop now completely unused GPIO definition header file.
- Delete all hardcoded IRQ number assignments. This hits
  MFD a bit so the patch has been ACKed by Lee Jones from
  the MFD side.

* tag 'ux500-dt-v3.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson

:
  mfd: dbx500/abx500: root out hardcoded IRQ assignments
  ARM: ux500: drop a chunk of GPIO definitions
  ARM: ux500: skip GIC CPU and dist address checks
  ARM: ux500: delete pointless DT config option
  ARM: u300: switch SSP/SPI clock name to "SSPCLK"
  ARM: ux500: switch SSP/SPI clock name to "SSPCLK"

Signed-off-by: Olof Johansson <olof@lixom.net>

Allwinner DT patches for 3.15, take 1 from Maxime Ripard:
  - Add SPI controllers for all the SoCs
  - Add various missing aliases
  - Add USB clocks nodes
  - Addition of the GMAC support
  - Introduction of the pcDuino board
  - A few DT cleanup patches: change of compatibles,

* tag 'sunxi-dt-for-3.15' of https://github.com/mripard/linux

: (33 commits)
  ARM: sun6i: dt: Fix mod0 compatible
  ARM: dts: sun7i: Enable the SPI controllers of the A20-olinuxino-micro
  ARM: dt: sun7i: Add SPI muxing options
  ARM: dt: sun5i: Add A13 SPI controller nodes
  ARM: dt: sun5i: Add A10s SPI controller nodes
  ARM: dt: sun4i: Add A10 SPI controller nodes
  ARM: dt: sun7i: Add A20 SPI controller nodes
  ARM: sun4i: dt: Remove grouping + simple-bus compatible for regulators
  ARM: sunxi: dt: Convert to the new clock compatibles
  ARM: sun7i: add arch timer node
  ARM: sun7i: dt: Add bindings for USB clocks
  ARM: sun5i: dt: Add bindings for USB clocks
  ARM: sun4i: dt: Add bindings for USB clocks
  ARM: dts: sun7i: Add ethernet alias for GMAC
  ARM: dts: sun7i: a20-olinuxino-micro: Enable GMAC instead of EMAC
  ARM: dts: sun7i: cubieboard2: Enable GMAC instead of EMAC
  ARM: dts: sun7i: cubietruck: Enable the GMAC
  ARM: dts: sun7i: Add pin muxing options for the GMAC
  ARM: dts: sun7i: Add GMAC controller node to sun7i DTSI
  ARM: dts: sun7i: Add GMAC clock node to sun7i DTSI
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'exynos-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Samsung exynos clock related DT updates for v3.15 from Kukjim Kim:

- use macros instead of hard coded numbers for clock bindings

NOTE: this is based on v3.15-next/dt-samsung

* tag 'exynos-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: use macros in clock bindings for exynos5440
  ARM: dts: use macros in clock bindings for exynos5420
  ARM: dts: use macros in clock bindings for exynos5250
  ARM: dts: use macros in clock bindings for exynos4

Merge tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

Samsung DT updates for v3.15 from Kukjin Kim:

For exynos4412
- update vdd_arm voltage range for odroidx board

For exynos5250
- add PMU sysreg node and update watchdog node
- re-organize RTC status
- add max77686 pmic node for smdk5250

For exynos5420
- add PMU sysreg, i2s, adma and watchdog nodes
- re-organize RTC status
- add fixed voltage regulators and regulator nodes
  for smdk5420
- add PMIC, GPIO based wake up key and vmmc-supply
  support for arndale-octa board

* tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung

:
  ARM: dts: Add vmmc-supply to MMC on arndale-octa board
  ARM: dts: Add wake up key to arndale-octa board
  ARM: dts: Add PMIC support to arndale-octa board
  ARM: dts: Add fixed voltage regulators to smdk5420
  ARM: dts: Add I2S nodes to exynos5420
  ARM: dts: Add ADMA node to exynos5420
  ARM: dts: Re-organize RTC status for exynos5250
  ARM: dts: Re-organize RTC status for exynos5420
  ARM: dts: Add regulator entries to smdk5420
  ARM: dts: add max77686 pmic node for smdk5250
  ARM: dts: update vdd_arm voltage range for exynos4412 based boards
  ARM: dts: update watchdog device nodes for exynos5250 and exynos5420
  ARM: dts: Add pmu sysreg node to exynos5250 and exynos5420

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v3.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

OMAP device tree changes from Tony Lindgren:

Device tree related changes for omaps with minor code
changes also to platform data quirks that are still needed
for some features.

* tag 'omap-for-v3.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (60 commits)
  ARM: dts: omap4+: Add DMM bindings
  ARM: dts: am43x-gp-evm: Add matrix gpio keys.
  ARM: dts: am43xx: add support for parallel NAND flash
  ARM: dts: AM33xx: updated default ECC scheme in nand-ecc-opt
  ARM: dts: am335x-evm: NAND: update MTD partition table
  ARM: OMAP2+: gpmc: update gpmc_hwecc_bch_capable() for new platforms and ECC schemes
  ARM: dts: omap3-gta04: Add bma180 accelerometer
  ARM: dts: omap3-gta04: Enable mmc2 for wifi
  ARM: dts: omap3-gta04: Add basic sound support
  ARM: dts: omap3-gta04: Add twl4030 charger
  ARM: dts: omap3-gta04: Add touchscreen properties
  ARM: dts: omap3-gta04: Add support for magnetometer
  ARM: dts: am437x-gp-evm: Enable gpio.
  ARM: dts: am437x-gp-evm: Add pwm backlight support.
  ARM: dts: am437x-gp-evm: Add gp dts.
  ARM: dts: am43x-epos-evm: Add SPI data.
  ARM: dts: am43x-epos-evm: Add I2C2 data.
  pinctrl: am43xx: dt-bindings: add MUX_MODE8
  ARM: dts: am43x-epos-evm: Add pwm backlight support.
  ARM: dts: am4372: Add pwm-cells property for ecap device.
  ...

The DBx500 and ABx500 should be getting their IRQs from the
device tree and nowhere else. Get rid of all the static assignments
everywhere, delete it from the driver, platform data and the
board files in one swift strike.

Lots of cross-dependencies in the MFD drivers for PRCMU and
AB8500 makes it necessary to strike everywhere at once to
eradicate IRQs passed as resources and platform data to the left
and right around the platform.

Cc: Mark Brown <broonie@kernel.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The Ux500 GPIOs are now assigned dynamically from the device tree.
Drop this table of static assignments.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'for_3.15/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.15/dt

Add craneboard devices
Add more N900 devices
Add am43x-epos-evm and am437x-gp-evm devices
Add OMAP4 DMM devices

Conflicts:
	arch/arm/boot/dts/am43x-epos-evm.dts
	arch/arm/boot/dts/dra7.dtsi

Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.

Add documentation for the DMM bindings.

Originally worked on by Andy Gross <andygro@gmail.com>

Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add gpio keys node for am43x gp evm.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
	On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected

Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
    commit ac65caf5


    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
    Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt

Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch has following updates, specific to MTD/NAND DT
 - update MTD NAND partition table to keep compatibility between
   different boards and mainline u-boot.
 - prefix 'NAND.' in names of NAND device MTD partitions to differentiate them
   from other MTD device partitions (like NOR and QSPI)
               Partition_Name            Partition_Size
    /dev/mtd0  NAND.SPL                  1 block-size*
    /dev/mtd1  NAND.SPL.backup1          1 block-size*
    /dev/mtd2  NAND.SPL.backup2          1 block-size*
    /dev/mtd3  NAND.SPL.backup3          1 block-size*
    /dev/mtd5  NAND.u-boot-spl-os        2 block-size* [for falcon boot]
    /dev/mtd4  NAND.u-boot               1 MB
    /dev/mtd6  NAND.u-boot-env           1 block-size*
    /dev/mtd7  NAND.u-boot-env.backup1   1 block-size*
    /dev/mtd8  NAND.kernel               till 0xA00000
    /dev/mtd9  NAND.file-system          till end of device

* am335x-evm uses NAND device with block-size=128KiB

Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch
 - refactors gpmc_hwecc_bch_capable()
 - add checks for new platforms like dra7xx, am43xx
 - add checks for OMAP3 SoC, w.r.t. new ECC schemes spawned in following commit:
    commit ac65caf5


    ARM: OMAP2+: cleaned-up DT support of various ECC schemes

Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add node for bma180 driver.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This requires vaux4.

Reset line isn't used yet, so wifi isn't reliable.
But it does work once per boot.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds basic sound support for gta04 board.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define twl4030 charger node used for charging.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Gta04 using tcs2007 touchscreen. Add support for that.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add magnetometer hmc5843 node.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable gpio3, gpio4, it will be used by gpio matrix keys. Also,
can be used by othe peripherals.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add pwm backlight support for gp evm.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add SPI dts data.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add I2C2 dts data.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

AM43xx devices have an extra MUX_MODE for certain pins.
Updating dt include to have MUX_MODE8 which maps to 0x8.

Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add pwm backlight support for am43x epos evm.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add "pwm-cells" node for all ecap, ehrpwm in am43x dtsi files.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This adds support for the bq24150a chip to the
Nokia N900 DTS file.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This adds support for the isp1704 chip to the Nokia N900
DTS file.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This adds support for the N900's headphone
amplifier to the N900 DTS file.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add support for tsl2563 light sensor to the Nokia N900.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add Keyboard Matrix information to N900's DTS file.
This patch maps the keys exactly as the original
board code.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add keypad node to twl4030, so that board DTS
files can just add the keymap.

Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

MMC 8 bit mode operation depends on dip switch setting which is not
obvious - The current board file has this description. However, with
removal of the board file in the future, this information will be lost
and has to be rediscovered.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Craneboard is a hardware development platform based on the Sitara
AM3517 ARM Cortex - A8 microprocessor device - see [1] for more
details. Add basic devices for craneboard as replacement for the board
file scheduled for removal as part of device tree conversion

[1] http://craneboard.org



Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Enable second USB channel and set it into 'host' mode.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Making it possible to reference and therefor change (disable) this
device node from other dts file which import this dtsi file.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add missing interrupt properties to the ecap0, ecap1, and ecap2
nodes.

Signed-off-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP34xx, AM3517 and OMAP36xx platforms use dpll1 clock.

OMAP443x, OMAP446x, OMAP447x, OMAP5, DRA7, AM43xx platforms use
dpll_mpu clock.

Latency used is the generic latency defined in omap-cpufreq
driver.

Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>