This patch prepares ground for the next VF MAC address change fix.
It lets untrusted VF to delete any VF mac filter, but it still
doesn't let untrusted VF to add mac filter not setup by PF.
It removes information duplication in num_mac mac filters counter.
And improves exact h/w mac filters usage checking in the
i40e_check_vf_permission() function by counting mac2add_cnt.
It also improves logging because now all mac addresses will be validated
first and corresponding messages will be logged.

Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

Add X710T*L device specific operations (in port LED detection and
handling of GLGEN_GPIO_CTL.PIN_FUNC field) to enable LED blinking.

Signed-off-by: Damian Milosek <damian.milosek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Let ethtool print driver and firmware versions when NIC is in
recovery mode.  Assign i40e_get_drvinfo() operation to ethtool
recovery mode operations.  Previously ethtool did not report
driver and firmware versions when NIC was in recovery mode.

Signed-off-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since commit 92418fb1

 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN/ITR0 registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.

Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.

This patch adds the correct conversion when writing the initial values to
the ITRN registers.

Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently FW use MDIO I/F number corresponded with current PF for PHY
access. This code allow to specify used MDIO I/F number.

Add new field - command flags with only one flag for now. Added flag
tells FW that it shouldn't change page while accessing QSFP module, as
it was set manually.

Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Move code detecting HW flags based on device type and FW API version
into a single function.

Signed-off-by: Piotr Azarewicz <piotr.azarewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix display of parameters "Configured FEC encodings:" and "Advertised
FEC modes:" in ethtool.  Implemented by setting proper FEC bits in
“advertising” bitmask of link_modes struct and “fec” bitmask in
ethtool_fecparam struct. Without this patch wrong FEC settings
can be shown.

Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes function to read NVM module data and uses it to
read current LLDP agent configuration from NVM API version 1.8.

Signed-off-by: Sylwia Wnuczko <sylwia.wnuczko@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Madalin Bucur says:

====================
DPAA Ethernet changes

v3: add newline at the end of error messages
v2: resending with From: field matching signed-off-by

Here's a series of changes for the DPAA Ethernet, addressing minor
or unapparent issues in the codebase, adding probe ordering based on
a recently added DPAA QMan API, removing some redundant code.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Newline was missing at the end of the error message.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove unused struct member second_largest_buf_size. Also, an out of
bounds access would have occurred in the removed code if there was only
one buffer pool in use.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DPAA Ethernet driver is using the FMan MAC as the device for DMA
mapping. This is not actually correct, as the real DMA device is the
FMan port (the FMan Rx port for reception and the FMan Tx port for
transmission). Changing the device used for DMA mapping to the Fman
Rx and Tx port devices.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an API that retrieves the 'struct device' that the specified FMan
port probed against. The new API will be used in a subsequent patch
that corrects the DMA devices used by the dpaa_eth driver.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Condition was previously checked, removing duplicate code.

Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the DPAA 1 Ethernet driver gets probed before the QBMan driver it will
cause a boot crash. Add predictability in the probing order by deferring
the Ethernet driver probe after QBMan and portals by using the recently
introduced QBMan APIs.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The liodn base registers are specific to PAMU based NXP systems and are
reserved on SMMU based ones. Don't access them unless PAMU is compiled in.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: PTP support for AQC devices

This patchset introduces PTP feature support in Aquantia AQC atlantic driver.

This implementation is a joined effort of aquantia developers:
Egor is the main designer and driver/firmware architect on PTP,
Sergey and Dmitry are included as co-developers.
Dmitry also helped me in the overall patchset preparations.

Feature was verified on AQC hardware with testptp tool, linuxptp,
gptp and with Motu hardware unit.

version3 updates:
- Review comments applied: error handling, various fixes

version2 updates:
- Fixing issues from Andrew's review: replacing self with
  ptp var name, making ptp_clk_offset a field in the ptp instance.
  devm_kzalloc advice is actually non applicable, because ptp object gets
  created/destroyed on each network device close/open and it should not be
  linked with dev lifecycle.
- Rearranging commit authorship, adding Egor as a ptp module main maintainer
- Fixing kbuild 32bit division issues
====================

Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PTP implementation is designed and maintained by Egor Pomozov, adding
him as this module maintainer. Egor is the author of the core
functionality and the architect, and is to be contacted for
all Aquantia PTP/AVB functionality.

Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Depending on FW configuration we can manage from 0 to 3 PINs for periodic output
and from 0 to 1 ext ts PIN for getting TS for external event.

Ext TS PIN functionality is implemented via periodic timestamps polling
directly from PHY, because right now there is now way to receive the
PIN trigger interrupt from phy.

The polling interval is 15 milliseconds.

Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GPIO PIN control and access is done by direct phy manipulation.
Here we add an aq_phy module which is able to access phy registers
via MDIO access mailbox.

Access is controlled via HW semaphore.

Co-developed-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethtool callback with basic information on what PTP features are supported
by the device.

Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here we add support for PTP specific IOCTLs of HW timestamp get/set.

These will use filters to configure flows onto the required queue ids.

Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We implement HW filter reservation for PTP traffic. Special location
in filters table is marked as reserved, because incoming ptp traffic
should be directed only to PTP designated queue. This way HW will do PTP
timestamping and proper processing.

Co-developed-by: Egor Pomozov <epomozov@marvell.com>
Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here we do alloc/free IRQs for PTP rings.
We also implement processing of PTP packets on TX and RX sides.

Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Checkpatch and styling fixes on parts of code touched by ptp

Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add implementations of PTP rings alloc/free.

PTP desing on this device uses two separate rings on a separate traffic
class for traffic rx/tx.

Third ring (hwts) is not a traffic ring, but is used only to receive timestamps
of the transmitted packets.

Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Basic HW functions implemented for adjusting frequency,
adjusting time, getting and setting time.
With these callbacks we now do register ptp clock in the system.

Firmware interface parts are defined for PTP requests and interactions.
Enable/disable PTP counters in HW on clock register/unregister.

Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make some other bit-enums more clear about positioning,
this helps on debugging and development

Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Here we add basic function for PTP clock register/unregister.
We also declare FW/HW capability bits used to control PTP feature on device.

PTP device is created if network card has appropriate FW that has PTP
enabled in config. HW supports timestamping for PTPv2 802.AS1 and
PTPv2 IPv4 UDP packets.

It also supports basic PTP callbacks for getting/setting time, adjusting
frequency and time as well.

Signed-off-by: Egor Pomozov <epomozov@marvell.com>
Co-developed-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Signed-off-by: Sergey Samoilenko <sergey.samoilenko@aquantia.com>
Co-developed-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/usb/lan78xx.c:3995:6: warning:
 variable event set but not used [-Wunused-but-set-variable]

It is never used, so can be removed.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Update main pool computation and pool size limits

Petr says:

In Spectrum ASICs, the shared buffer is an area of memory where packets are
kept until they can be transmitted. There are two resources associated with
shared buffer size: cap_total_buffer_size and cap_guaranteed_shared_buffer.
So far, mlxsw has been using the former as a limit when validating shared
buffer pool size configuration. However, the total size also includes
headrooms and reserved space, which really cannot be used for shared buffer
pools. Patch #1 mends this and has mlxsw use the guaranteed size.

To configure default pool sizes, mlxsw has historically hard-coded one or
two smallish pools, and one "main" pool that took most of the shared buffer
(that would be pool 0 on ingress and pool 4 on egress). During the
development of Spectrum-2, it became clear that the shared buffer size
keeps shrinking as bugs are identified and worked around. In order to
prevent having to tweak the size of pools 0 and 4 to catch up with updates
to values reported by the FW, patch #2 changes the way these pools are set.
Instead of hard-coding a fixed value, the main pool now takes whatever is
left from the guaranteed size after the smaller pool(s) are taken into
account.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of hard-coding the size of the largest pool, calculate it from the
reported guaranteed shared buffer size and sizes of other pools (currently
only the CPU port pool).

Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two resources associated with shared buffer size:
cap_total_buffer_size, and cap_guaranteed_shared_buffer. So far, mlxsw has
been using the former as a limit to determine how large a pool size is
allowed to be. However, the total size also includes headrooms and reserved
space, which really cannot be used for shared buffer pools.

Therefore convert mlxsw to use the latter resource as a limit. Adjust
hard-coded pool sizes to be the guaranteed size minus 256000 bytes for CPU
port pool. On Spectrum-1 that actually leads to an increase. A follow-up
patch will have this size calculated automatically.

Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Setting PCI_EXP_DEVCTL_NOSNOOP_EN for certain chip versions had been
added to the vendor driver more than 10 years ago, and copied from
there to r8169. It has been removed from the vendor driver meanwhile
and I think we can safely remove this too.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tao Ren says:

====================
net: phy: support 1000Base-X auto-negotiation for BCM54616S

This patch series aims at supporting auto negotiation when BCM54616S is
running in 1000Base-X mode: without the patch series, BCM54616S PHY driver
would report incorrect link speed in 1000Base-X mode.

Patch #1 (of 3) modifies assignment to OR when dealing with dev_flags in
phy_attach_direct function, so that dev_flags updated in BCM54616S PHY's
probe callback won't be lost.

Patch #2 (of 3) adds several genphy_c37_* functions to support clause 37
1000Base-X auto-negotiation, and these functions are called in BCM54616S
PHY driver.

Patch #3 (of 3) detects BCM54616S PHY's operation mode and calls according
genphy_c37_* functions to configure auto-negotiation and parse link
attributes (speed, duplex, and etc.) in 1000Base-X mode.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

The BCM54616S PHY cannot work properly in RGMII->1000Base-X mode, mainly
because genphy functions are designed for copper links, and 1000Base-X
(clause 37) auto negotiation needs to be handled differently.

This patch enables 1000Base-X support for BCM54616S by customizing 3
driver callbacks, and it's verified to be working on Facebook CMM BMC
platform (RGMII->1000Base-KX):

  - probe: probe callback detects PHY's operation mode based on
    INTERF_SEL[1:0] pins and 1000X/100FX selection bit in SerDES 100-FX
    Control register.

  - config_aneg: calls genphy_c37_config_aneg when the PHY is running in
    1000Base-X mode; otherwise, genphy_config_aneg will be called.

  - read_status: calls genphy_c37_read_status when the PHY is running in
    1000Base-X mode; otherwise, genphy_read_status will be called.

Note: BCM54616S PHY can also be configured in RGMII->100Base-FX mode, and
100Base-FX support is not available as of now.

Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for clause 37 1000Base-X auto-negotiation.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Tested-by: René van Dorst <opensource@vdorst.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify the assignment to OR when dealing with phydev->dev_flags in
phy_attach_direct function, and this is to make sure dev_flags set in
driver's probe callback won't be lost.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
CC: Heiner Kallweit <hkallweit1@gmail.com>
CC: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tao Ren <taoren@fb.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 342db221

 ("sched: Call skb_get_hash_perturb
in sch_fq_codel") we no longer need anything from this file.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>

Vivien Didelot says:

====================
The dsa_switch structure represents the physical switch device itself,
and is allocated by the driver. The dsa_switch_tree and dsa_port structures
represent the logical switch fabric (eventually composed of multiple switch
devices) and its ports, and are allocated by the DSA core.

This branch lists the logical ports directly in the fabric which simplifies
the iteration over all ports when assigning the default CPU port or configuring
the D in DSA in drivers like mv88e6xxx.

This also removes the unique dst->cpu_dp pointer and is a first step towards
supporting multiple CPU ports and dropping the DSA_MAX_PORTS limitation.

Because the dsa_port structures are not tied to the dsa_switch structure
anymore, we do not need to provide an helper for the drivers to allocate a
switch structure. Like in many other subsystems, drivers can now embed their
dsa_switch structure as they wish into their private structure. This will
be particularly interesting for the Broadcom drivers which were currently
limited by the dynamically allocated array of DSA ports.

The series implements the list of dsa_port structures, makes use of it,
then drops dst->cpu_dp and the dsa_switch_alloc helper.
====================

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>