Add nodes for the 4 mmc controllers found on A31 SoCs to
arch/arm/boot/dts/sun6i-a31.dtsi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add clk-nodes for the mmc clocks.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 3 mmc controllers found on A10s SoCs and for the 2 mmc
controllers found on A13 SoCs.

Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Tested on a subset of these boards, for the others boards the settings match
the ones of the tested boards according to the original firmware fex files.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc0 is the only controller actually being used on boards, so limit the
pin-muxing options to that.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the 4 mmc controllers found on A10 SoCs to
arch/arm/boot/dts/sun4i-a10.dtsi.

Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds  pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the PWM for both PWM channels on the cubietruck. They can be found on
connector CN8.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the PWM bindings for the Allwinner A20.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the PWM bindings for the Allwinner A10.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl descriptions for both PWM channels of the Allwinner A20.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the pinctrl descriptions for both PWM channels of the Allwinner A10.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the performance monitoring unit found in the A31 SoCs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>

Enable the performance monitoring unit found in the A20 SoCs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>

Now that we have a DMA driver, we can add the DMA bindings in the DTSI for the
controller and the devices supported that can use DMA.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

The DT are supposed to be ordered by physical address. Move the NMI node where
it belongs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The prcm lives at address 0x01f01400 as the reg entry in its node already
correctly indicates, rename the node to match this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Commit 8f619b54

 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode.  The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic.  The visible result is that
the kernel hangs after printing "returning from prom_init".

This fixes it by checking for hypervisor mode being available before
setting LPCR.  If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

using IS_ENABLED() macro instead of defined(CONFIG_XXX) || defined(CONFIG_XXX_MODULE)

Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

In v3.2 the Analog Devices ADT75 temperature sensor driver was removed
as an IIO driver and support for it was added to the LM75 HWMON driver.
But it was apparently overlooked to rename one reference to CONFIG_ADT75
to CONFIG_SENSORS_LM75. Do so now. Use the IS_ENABLED() macro, while
we're at it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

In v3.2 the Analog Devices AD7314 temperature sensor driver was removed
as an IIO driver and added as a HWMON driver. But it was apparently
overlooked to rename two references to CONFIG_AD7314 to
CONFIG_SENSORS_AD7314. Do so now. Use the IS_ENABLED() macro, while
we're at it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

In v3.2 the Analog Devices ad2s1200/ad2s1205 driver was renamed from
ad2s120x to ad2s1200. But it apparently forgot to rename the references
to this driver in the BF537-STAMP code. Rename these now, and use the
IS_ENABLED() macro, while we're at it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

There's a (rather subtle) typo in "CONFIG_SND_SOC_ADV80X_MODULE". Fix it
once and for all by using IS_ENABLED(), which is designed to avoid
issues like this.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

drop unused head file
change pinmux request/free macro for backward compatiblity
add function declaration

Signed-off-by: Steven Miao <realmz6@gmail.com>

The IRET instruction, when returning to a 16-bit segment, only
restores the bottom 16 bits of the user space stack pointer.  We have
a software workaround for that ("espfix") for the 32-bit kernel, but
it relies on a nonzero stack segment base which is not available in
32-bit mode.

Since 16-bit support is somewhat crippled anyway on a 64-bit kernel
(no V86 mode), and most (if not quite all) 64-bit processors support
virtualization for the users who really need it, simply reject
attempts at creating a 16-bit segment when running on top of a 64-bit
kernel.

Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-kicdm89kzw9lldryb1br9od0@git.kernel.org
Cc: <stable@vger.kernel.org>

The only user of Kconfig symbol IP_CHECKSUM_L1 got removed in v2.6.33,
with commit ddf9ddac

 ("Blackfin: convert
to generic checksum code"). We can remove the Kconfig entry for this
unused symbol now.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

The Kconfig symbol GENERIC_GPIO was removed in v3.10. Nothing cares
about it anymore. It popped up somehow in v3.13, so it can be removed
again.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

There is nothing special in that blackfin code. Use the core
implementation.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Steven Miao <realmz6@gmail.com>
Cc: bfin <adi-buildroot-devel@lists.sourceforge.net>

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

New kexec-tools wants to pass kdump kernel needed memmap via E820
directly, instead of memmap=exactmap. This makes saved_max_pfn not
be passed down to 2nd kernel. To keep 1st kernel and 2nd kernel using
the same TCE table size, Muli suggest to hard code the size to max (8M).

We can't get rid of saved_max_pfn this time, for backward compatibility
with old first kernel and new second kernel. However new first kernel
and old second kernel can not work unfortunately.

v2->v1:
- retain saved_max_pfn so new 2nd kernel can work with old 1st kernel
  from Vivek

Signed-off-by: WANG Chao <chaowang@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Muli Ben-Yehuda <mulix@mulix.org>
Acked-by: Jon Mason <jdmason@kudzu.us>
Link: http://lkml.kernel.org/r/1394463120-26999-1-git-send-email-chaowang@redhat.com


Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>