Move pmu, usbphy0 and usbphy1 nodes from soc node to root node.

The nodes that have been moved do not have any register properties and thus
shouldn't be placed on the bus.

This fixes the following build warnings with W=1:

arch/arm/boot/dts/imx53-ard.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-0 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/aips@50000000/usbphy-1 missing or empty reg/ranges property
arch/arm/boot/dts/imx53-ard.dtb: Warning (simple_bus_reg): Node /soc/pmu missing or empty reg/ranges property

Based on a patch from Simon Horman for r8a7795.dtsi.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This node is for Low Power General Purpose Register which can
be used as Non-Volatile Storage.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse. To use the TMR_FIPER1
register to generate a 1 PPS event, the value
(10^9 nanoseconds) - TCLK_PERIOD should be programmed.
It should be 999999995 not 999999990 since TCLK_PERIOD
is 5.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the partitions definition for the SPI NOR to provide
backward compatibility with the documented[1] layout used with
Boundary Devices BSP.

1. https://boundarydevices.com/boot-flash-access-linux/



It exports to Linux:

 mtd0: bootloader
 mtd1: env
 mtd2: splash

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fabio Estevam suggested using GPIO_ACTIVE_HIGH in the gpio specification
for the USB regulators.  Change them to conform.

Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Cubox-i and Hummingboard variants for v1.5 SOMs, where the SOM has
eMMC fitted.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add Cubox-i and Hummingboard variants for v1.5 SOMs, which have TI
Wi-Fi instead of Broadcom Wi-Fi.  This variant does not include
SOM eMMC support.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Node names are supposed to be generic, fix the RTC and codec node
names for both Hummingboard and Cubox-i.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make the regulators match the schematic - name the regulators after
one of their schematic supply names, and arrange them into their
heirarchy.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the SD card regulator, which allows the SD card power to be switched
on/off.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rev 1.5 microsoms include eMMC support on-board.  Add a microsom include
file which can be used to add support for this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the TI Wi-Fi WL1837 device on SolidRun's revision
1.5 microsoms.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a 3.3V regulator for devices connected to the vcc_3v3 supply
signal on the microsom.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The SDIO clock is really the Broadcom clock.  Rename it as such.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are two variants of the imx6qdl som: one with Broadcom Wi-Fi and
another with Texas Instruments Wi-Fi.  The two Wi-Fi devices require
different DT bindings, so it's necessary to split out the Broadcom
specifics.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use real iomuxc values rather than preserving the boot loader value for
the SOMs ethernet.

Suggested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the microsom includes into the .dts files so different options can
be accomodated at the lowest level.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Jon and myself feel that "imx6qdl-microsom" is too generic a name for
SolidRun's microsom - some other manufacturer could have their own
microsom.  Change the name to the shorter "imx6qdl-sr-som".

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file.  Move the
AR8035 support into the main imx6qdl-microsom file.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The regulators node is redundant, and serves no useful function.
Remove it from i.MX6 SolidRun platforms.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

UDOO board has a possibility to disable most of imx6 SoC power supplies via
"EN_5V" signal, which is connected to "NANDF_D4" pad.

This reduces current consumption after shutdown from ~350 mA to ~40 mA and
prevents a SoC watchdog from starting it again on its own after the
watchdog timeout expires (previously it was not possible to shut down the
SoC permanently if its watchdog was ever enabled since it was still ticking
after the shutdown).

Unfortunately, this does not extinguish the "Power" LED (as it is powered
from an always-on voltage regulator).

To power the SoC up again press the power button (SW2, the one with a long
shaft).

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As explained in Documentation/devicetree/bindings/net/fsl-fec.txt the
phy-reset-gpios is active high only if the 'phy-reset-active-high' is
present.

As 'phy-reset-active-high' is not used here, fix the device tree
description by passing GPIO_ACTIVE_LOW flag.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

HDMI_TX_CEC_LINE pin is used for CEC, so pass it in the device tree.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On imx6qdl-sabreauto the HDMI DDC bus is connected to I2C2, so
pass the 'ddc-i2c-bus' property accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for PCIe support.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is not recommended to place regulators inside "simple-bus", so
move them out. The motivation for doing this is to make it easier to
adding new regulators.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently the imx pci driver fails to probe on i.MX6SX.

Fix the PCI representation so that the driver can be probed and
PCI devices can be detected.

Tested on a im6sx-sdb board:

00:00.0 Class 0604: 16c3:abcd
01:00.0 Class 0280: 8086:08b1

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

AC'97 interface RXD and TXC pins are only used as SoC inputs, let's disable
pad drivers for them so we will be protected if, for example, TCLKDIR is
set by mistake in AUDMUX and causes TXC pin to be configured as an output.

This also changes pull direction on these pins from pull-up to pull-down
to match what the board AC'97 CODEC chip (VT1613) has on these pins.

Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Commit a22950c8 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Ls1021a esdhc had been enabled in uboot,
but it had not been enabled it in kernel,
So set the esdhc's status to "okay".

Signed-off-by: yinbo.zhu <yinbo.zhu@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The two Ethernet switches have an AT24C512 each. This is a 64K device,
not 512 bytes as currently listed in the device tree.

Reported-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.

Fixes the following warning in i.MX dts files:

Warning (phys_property): Missing property '#phy-cells' in node ...

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This makes sure that the battery backed RTC is always the
primary one, regardless of the driver probe ordering.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This renames the audio device to "Front" in order to match the RDU2
naming, which makes it easier for a unified userspace to deal with
both boards.

Also rename the phandle for the headphone amplifier to more closely
resemble the RDU2 DTS.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There are 0 ohm resistors that allow selecting the EDID I2C port to
be I2C1 or I2C2.

On revd1 the 0 ohm resistors are populated in such a way that the I2C2
is used as DDC I2C bus, so fix it accordingly.

Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx7s/imx7d has the ptp interrupt newly added as well.

For imx7, "int0" is the interrupt for queue 0 and ENET_MII
"int1" is for queue 1
"int2" is for queue 2

For imx6sx, "int0" handles all 3 queues and ENET_MII

And of course, the "pps" interrupt is for the PTP_CLOCK_PPS interrupts
This will help document what each interrupt does.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is needed for the bootloader to patch in the correct MAC address.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warning is seen with W=1:

Warning (unit_address_vs_reg): Node /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has a unit name, but no reg property

Fix this warning by adding reg property from such node and, consequently,
includes a mdio node into the fec node, with the 'address-cells' and
'size-cells' to avoid these other following warnings:

Warning (reg_format): "reg" property in /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/aips@60000000/ethernet@63fec000/ethernet-phy@0

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Tested-by: Lothar Waßmann <LW@karo-electronics.de>
Acked-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions

Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>