- Jun 18, 2020
-
-
Phil Elwell authored
At present there is no mechanism to specify driver load order, which can lead to deferrals and repeated retries until successful. Since this situation is expected, reduce the dmesg level to INFO and mention that the operation will be retried. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
Eric Anholt authored
These divide off of PLLD_PER and are used for the ethernet and wifi PHYs source PLLs. Neither of them is currently represented by a phy device that would grab the clock for us. This keeps other drivers from killing the networking PHYs when they disable their own clocks and trigger PLLD_PER's refcount going to 0. v2: Skip marking as critical if they aren't on at boot. Signed-off-by: Eric Anholt <eric@anholt.net>
-
Phil Elwell authored
The VPU is responsible for managing the core clock, usually under direction from the bcm2835-cpufreq driver but not via the clk-bcm2835 driver. Since the core frequency can change without warning, it is safer to report the maximum clock rate to users of the core clock - I2C, SPI and the mini UART - to err on the safe side when calculating clock divisors. If the DT node for the clock driver includes a reference to the firmware node, use the firmware API to query the maximum core clock instead of reading the divider registers. Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about 160KHz. In particular, switching to the 4.9 kernel was likely to break SenseHAT usage on a Pi3. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
Phil Elwell authored
The claim-clocks property can be used to prevent PLLs and dividers from being marked as critical. It contains a vector of clock IDs, as defined by dt-bindings/clock/bcm2835.h. Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and PLLH_PIX for the vc4_kms_v3d driver. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
Phil Elwell authored
The VPU configures and relies on several PLLs and dividers. Mark all enabled dividers and their PLLs as CRITICAL to prevent the kernel from switching them off. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
popcornmix authored
Avoids the 0x40000 cycles of warmup again if firmware has already used it
-
Martin Sperl authored
Register the clocks early during the boot process, so that special/critical clocks can get enabled early on in the boot process avoiding the risk of disabling a clock, pll_divider or pll when a claiming driver fails to install propperly - maybe it needs to defer. Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
-
popcornmix authored
-
popcornmix authored
-
Noralf Trønnes authored
The Raspberry Pi firmware looks at the RSTS register to know which partition to boot from. The reboot syscall command LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument. Add support for passing in a partition number 0..63 to boot from. Partition 63 is a special partiton indicating halt. If the partition doesn't exist, the firmware falls back to partition 0. Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
-
Phil Elwell authored
Without this alias, Device Tree won't cause the driver to be loaded. See: https://github.com/raspberrypi/linux/pull/1510
-
popcornmix authored
-
Noralf Trønnes authored
Load driver early since at least bcm2708_fb doesn't support deferred probing and even if it did, we don't want the video driver deferred. Support the legacy DMA API which is needed by bcm2708_fb. Don't mask out channel 2. Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
-
Phil Elwell authored
An alternative strategy would be to use "rpi,spidev" instead, but that would require many Raspberry Pi Device Tree changes. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
Noralf Trønnes authored
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
-
Noralf Trønnes authored
Add a duplicate irq range with an offset on the hwirq's so the driver can detect that enable_fiq() is used. Tested with downstream dwc_otg USB controller driver. Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org>
-
Phil Elwell authored
Initialise the level for each IRQ to avoid a warning from the arm arch timer code. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
Phil Elwell authored
The old arch-specific IRQ macros included a dsb to ensure the write to clear the mailbox interrupt completed before returning from the interrupt. The BCM2836 irqchip driver needs the same precaution to avoid spurious interrupts. Spurious interrupts are still possible for other reasons, though, so trap them early.
-
Phil Elwell authored
Without this patch, removing a device tree overlay can crash here. Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
popcornmix authored
Signed-off-by: popcornmix <popcornmix@gmail.com>
-
Sam Nazarko authored
See: http://forum.kodi.tv/showthread.php?tid=285288
-
Steve Glendinning authored
smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings. This patch stops smsc95xx from changing truesize. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
-
Phil Elwell authored
This reverts commit ede44c90. See: https://github.com/raspberrypi/firmware/issues/1065 Signed-off-by: Phil Elwell <phil@raspberrypi.org>
-
Dan Pasanen authored
* Re-expose some dmi APIs for use in VCSM
-
- Jun 17, 2020
-
-
Greg Kroah-Hartman authored
-
Marc Zyngier authored
commit ef3e40a7 upstream. When using the PtrAuth feature in a guest, we need to save the host's keys before allowing the guest to program them. For that, we dump them in a per-CPU data structure (the so called host context). But both call sites that do this are in preemptible context, which may end up in disaster should the vcpu thread get preempted before reentering the guest. Instead, save the keys eagerly on each vcpu_load(). This has an increased overhead, but is at least safe. Cc: stable@vger.kernel.org Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marc Zyngier authored
commit 0370964d upstream. On a VHE system, the EL1 state is left in the CPU most of the time, and only syncronized back to memory when vcpu_put() is called (most of the time on preemption). Which means that when injecting an exception, we'd better have a way to either: (1) write directly to the EL1 sysregs (2) synchronize the state back to memory, and do the changes there For an AArch64, we already do (1), so we are safe. Unfortunately, doing the same thing for AArch32 would be pretty invasive. Instead, we can easily implement (2) by calling the put/load architectural backends, and keep preemption disabled. We can then reload the state back into EL1. Cc: stable@vger.kernel.org Reported-by: James Morse <james.morse@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mattia Dongili authored
commit 476d60b1 upstream. The thermal handle object may fail initialization when the module is loaded in the first place. Avoid attempting to use it on resume then. Fixes: 6d232b29 ("ACPICA: Dispatcher: always generate buffer objects for ASL create_field() operator") Reported-by: Dominik Mierzejewski <dominik@greysector.net> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207491 Signed-off-by: Mattia Dongili <malattia@linux.it> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mattia Dongili authored
commit 47828d22 upstream. After commit 6d232b29 ("ACPICA: Dispatcher: always generate buffer objects for ASL create_field() operator") ACPICA creates buffers even when new fields are small enough to fit into an integer. Many SNC calls counted on the old behaviour. Since sony-laptop already handles the INTEGER/BUFFER case in sony_nc_buffer_call, switch sony_nc_int_call to use its more generic function instead. Fixes: 6d232b29 ("ACPICA: Dispatcher: always generate buffer objects for ASL create_field() operator") Reported-by: Dominik Mierzejewski <dominik@greysector.net> Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207491 Reported-by: William Bader <williambader@hotmail.com> Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1830150 Signed-off-by: Mattia Dongili <malattia@linux.it> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Juergen Gross authored
commit c8d70a29 upstream. backend_connect() can fail, so switch the device to connected only if no error occurred. Fixes: 0a9c75c2 ("xen/pvcalls: xenbus state handling") Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Link: https://lore.kernel.org/r/20200511074231.19794-1-jgross@suse.com Reviewed-by: Stefano Stabellini <sstabellini@kernel.org> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Kosina authored
commit 263c6158 upstream. Since the switch of floppy driver to blk-mq, the contended (fdc_busy) case in floppy_queue_rq() is not handled correctly. In case we reach floppy_queue_rq() with fdc_busy set (i.e. with the floppy locked due to another request still being in-flight), we put the request on the list of requests and return BLK_STS_OK to the block core, without actually scheduling delayed work / doing further processing of the request. This means that processing of this request is postponed until another request comes and passess uncontended. Which in some cases might actually never happen and we keep waiting indefinitely. The simple testcase is for i in `seq 1 2000`; do echo -en $i '\r'; blkid --info /dev/fd0 2> /dev/null; done run in quemu. That reliably causes blkid eventually indefinitely hanging in __floppy_read_block_0() waiting for completion, as the BIO callback never happens, and no further IO is ever submitted on the (non-existent) floppy device. This was observed reliably on qemu-emulated device. Fix that by not queuing the request in the contended case, and return BLK_STS_RESOURCE instead, so that blk core handles the request rescheduling and let it pass properly non-contended later. Fixes: a9f38e1d ("floppy: convert to blk-mq") Cc: stable@vger.kernel.org Tested-by: Libor Pechacek <lpechacek@suse.cz> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulf Hansson authored
commit a94a59f4 upstream. Over the years, the code in mmc_sdio_init_card() has grown to become quite messy. Unfortunate this has also lead to that several paths are leaking memory in form of an allocated struct mmc_card, which includes additional data, such as initialized struct device for example. Unfortunate, it's a too complex task find each offending commit. Therefore, this change fixes all memory leaks at once. Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20200430091640.455-3-ulf.hansson@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulf Hansson authored
commit f04086c2 upstream. During some scenarios mmc_sdio_init_card() runs a retry path for the UHS-I specific initialization, which leads to removal of the previously allocated card. A new card is then re-allocated while retrying. However, in one of the corresponding error paths we may end up to remove an already removed card, which likely leads to a NULL pointer exception. So, let's fix this. Fixes: 5fc3d80e ("mmc: sdio: don't use rocr to check if the card could support UHS mode") Cc: <stable@vger.kernel.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Link: https://lore.kernel.org/r/20200430091640.455-2-ulf.hansson@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ludovic Desroches authored
commit a1af7f36 upstream. Remove non-removable and mmc-ddr-1_8v properties from the sdmmc0 node which come probably from an unchecked copy/paste. Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com> Fixes:42ed5355 "ARM: dts: at91: introduce the sama5d2 ptc ek board" Cc: stable@vger.kernel.org # 4.19 and later Link: https://lore.kernel.org/r/20200401221504.41196-1-ludovic.desroches@microchip.com Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Masahiro Yamada authored
commit 5d1f42e1 upstream. Currently, tmio_mmc_irq() handler is registered before the host is fully initialized by tmio_mmc_host_probe(). I did not previously notice this problem. The boot ROM of a new Socionext SoC unmasks interrupts (CTL_IRQ_MASK) somehow. The handler is invoked before tmio_mmc_host_probe(), then emits noisy call trace. Move devm_request_irq() below tmio_mmc_host_probe(). Fixes: 3fd784f7 ("mmc: uniphier-sd: add UniPhier SD/eMMC controller driver") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200511062158.1790924-1-yamada.masahiro@socionext.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ulf Hansson authored
commit 4bd78441 upstream. Before calling tmio_mmc_host_probe(), the caller is required to enable clocks for its device, as to make it accessible when reading/writing registers during probe. Therefore, the responsibility to disable these clocks, in the error path of ->probe() and during ->remove(), is better managed outside tmio_mmc_host_remove(). As a matter of fact, callers of tmio_mmc_host_remove() already expects this to be the behaviour. However, there's a problem with tmio_mmc_host_remove() when the Kconfig option, CONFIG_PM, is set. More precisely, tmio_mmc_host_remove() may then disable the clock via runtime PM, which leads to clock enable/disable imbalance problems, when the caller of tmio_mmc_host_remove() also tries to disable the same clocks. To solve the problem, let's make sure tmio_mmc_host_remove() leaves the device with clocks enabled, but also make sure to disable the IRQs, as we normally do at ->runtime_suspend(). Reported-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20200519152434.6867-1-ulf.hansson@linaro.org Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ludovic Barre authored
commit fe8d33bd upstream. Turning on CONFIG_DMA_API_DEBUG_SG results in the following warning: WARNING: CPU: 1 PID: 20 at kernel/dma/debug.c:500 add_dma_entry+0x16c/0x17c DMA-API: exceeded 7 overlapping mappings of cacheline 0x031d2645 Modules linked in: CPU: 1 PID: 20 Comm: kworker/1:1 Not tainted 5.5.0-rc2-00021-gdeda30999c2b-dirty #49 Hardware name: STM32 (Device Tree Support) Workqueue: events_freezable mmc_rescan [<c03138c0>] (unwind_backtrace) from [<c030d760>] (show_stack+0x10/0x14) [<c030d760>] (show_stack) from [<c0f2eb28>] (dump_stack+0xc0/0xd4) [<c0f2eb28>] (dump_stack) from [<c034a14c>] (__warn+0xd0/0xf8) [<c034a14c>] (__warn) from [<c034a530>] (warn_slowpath_fmt+0x94/0xb8) [<c034a530>] (warn_slowpath_fmt) from [<c03bca0c>] (add_dma_entry+0x16c/0x17c) [<c03bca0c>] (add_dma_entry) from [<c03bdf54>] (debug_dma_map_sg+0xe4/0x3d4) [<c03bdf54>] (debug_dma_map_sg) from [<c0d09244>] (sdmmc_idma_prep_data+0x94/0xf8) [<c0d09244>] (sdmmc_idma_prep_data) from [<c0d05a2c>] (mmci_prep_data+0x2c/0xb0) [<c0d05a2c>] (mmci_prep_data) from [<c0d073ec>] (mmci_start_data+0x134/0x2f0) [<c0d073ec>] (mmci_start_data) from [<c0d078d0>] (mmci_request+0xe8/0x154) [<c0d078d0>] (mmci_request) from [<c0cecb44>] (mmc_start_request+0x94/0xbc) DMA api debug brings to light leaking dma-mappings, dma_map_sg and dma_unmap_sg are not correctly balanced. If a request is prepared, the dma_map/unmap are done in asynchronous call pre_req (prep_data) and post_req (unprep_data). In this case the dma-mapping is right balanced. But if the request was not prepared, the data->host_cookie is define to zero and the dma_map/unmap must be done in the request. The dma_map is called by mmci_dma_start (prep_data), but there is no dma_unmap in this case. This patch adds dma_unmap_sg when the dma is finalized and the data cookie is zero (request not prepared). Signed-off-by: Ludovic Barre <ludovic.barre@st.com> Link: https://lore.kernel.org/r/20200526155103.12514-2-ludovic.barre@st.com Fixes: 46b723dd ("mmc: mmci: add stm32 sdmmc variant") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eugen Hristev authored
commit dbdea70f upstream. When enabling calibration at reset, the CALCR register was completely rewritten. This may cause certain bits being deleted unintentedly. Fix by issuing a read-modify-write operation. Fixes: 727d836a ("mmc: sdhci-of-at91: add DT property to enable calibration on full reset") Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com> Link: https://lore.kernel.org/r/20200527105659.142560-1-eugen.hristev@microchip.com Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Veerabhadrarao Badiganti authored
commit 9253d710 upstream. Clear tuning_done flag while executing tuning to ensure vendor specific HS400 settings are applied properly when the controller is re-initialized in HS400 mode. Without this, re-initialization of the qcom SDHC in HS400 mode fails while resuming the driver from runtime-suspend or system-suspend. Fixes: ff06ce41 ("mmc: sdhci-msm: Add HS400 platform support") Cc: stable@vger.kernel.org Signed-off-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org> Link: https://lore.kernel.org/r/1590678838-18099-1-git-send-email-vbadigan@codeaurora.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Chris Wilson authored
commit f30d3ced upstream. After changing the timing between GTT updates and execution on the GPU, we started seeing sporadic failures on Ironlake. These were narrowed down to being an insufficiently strong enough barrier/delay after updating the GTT and scheduling execution on the GPU. By forcing the uncached read, and adding the missing barrier for the singular insert_page (relocation paths), the sporadic failures go away. Fixes: 983d308c ("agp/intel: Serialise after GTT updates") Fixes: 3497971a ("agp/intel: Flush chipset writes after updating a single PTE") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Acked-by: Andi Shyti <andi.shyti@intel.com> Cc: stable@vger.kernel.org # v4.0+ Link: https://patchwork.freedesktop.org/patch/msgid/20200410083535.25464-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-