When the N_TTY line discipline receives data and wakes readers to
process the input, polling writers are also mistakenly woken. This
is because, although readers and writers are differentiated by
different wait queues (tty->read_wait & tty->write_wait), both
wait queues are polled together. Thus, reader wakeups without poll
flags still cause poll(POLLOUT) to wakeup.

For received data, wakeup readers with POLLIN. Preserve the
unspecific wakeup in n_tty_packet_mode_flush(), as this action
should flag both POLLIN and POLLOUT.

Fixes epoll_wait() for edge-triggered EPOLLOUT.

Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In case if we're releasing the last tty reference the following
call sequence is possible

tty_driver_kref_put
  destruct_tty_driver
    kfree(driver);

where @driver is used in next module_put call, which leads to

 | [ 285.964007] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 | [ 285.964007] Workqueue: events release_one_tty
 | [ 285.964007] task: ffff8800cc7ea5f0 ti: ffff8800cb800000 task.ti: ffff8800cb800000
 | [ 285.964007] RIP: 0010:[<ffffffff810aeaf5>] [<ffffffff810aeaf5>] module_put+0x24/0xf4
 | [ 285.964007] RSP: 0018:ffff8800cb801d48 EFLAGS: 00010213
 | [ 285.964007] RAX: ffff8800cb801fd8 RBX: ffff8800ca3429d0 RCX: ffff8800cb1db400
 | [ 285.964007] RDX: 0000000000000000 RSI: ffffffff817349c1 RDI: 0000000000000001
 | [ 285.964007] RBP: ffff8800cb801d60 R08: ffff8800cd632b40 R09: 0000000000000000
 | [ 285.964007] R10: 00000000ffffffff R11: ffff88011f40a000 R12: 6b6b6b6b6b6b6b6b
 | [ 285.964007] R13: ffff8800ca342520 R14: 0000000000000000 R15: ffff88011f5d8200
 | [ 285.964007] FS: 0000000000000000(0000) GS:ffff88011f400000(0000) knlGS:0000000000000000
 | [ 285.964007] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 | [ 285.964007] CR2: 00007faf5229d090 CR3: 0000000001c0b000 CR4: 00000000000006f0
 | [ 285.964007] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
 | [ 285.964007] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
 | [ 285.964007] Stack:
 | [ 285.964007] ffff8800ca3429d0 ffff8800ca342a30 ffff8800ca342520 ffff8800cb801d88
 | [ 285.964007] ffffffff8146554a ffff8800cc77cc78 ffff8800ca3429d0 ffff88011f5d3800
 | [ 285.964007] ffff8800cb801e08 ffffffff810683c1 ffffffff810682ff 0000000000000046
 | [ 285.964007] Call Trace:
 | [ 285.964007] [<ffffffff8146554a>] release_one_tty+0x54/0xa3
 | [ 285.964007] [<ffffffff810683c1>] process_one_work+0x223/0x404
 | [ 285.964007] [<ffffffff810682ff>] ? process_one_work+0x161/0x404
 | [ 285.964007] [<ffffffff81068971>] worker_thread+0x136/0x205
 | [ 285.964007] [<ffffffff8106883b>] ? rescuer_thread+0x26a/0x26a
 | [ 285.964007] [<ffffffff8106e5bf>] kthread+0xa2/0xaa
 | [ 285.964007] [<ffffffff810a4586>] ? trace_hardirqs_on_caller+0x16/0x1eb
 | [ 285.964007] [<ffffffff8106e51d>] ? __kthread_parkme+0x65/0x65
 | [ 285.964007] [<ffffffff8173f59c>] ret_from_fork+0x7c/0xb0
 | [ 285.964007] [<ffffffff8106e51d>] ? __kthread_parkme+0x65/0x65
 | [ 285.964007] Code: 09 00 5b 41 5c 5d c3 0f 1f 44 00 00 55 48 85 ff 48 89 e5 41 55 41 54 49 89 fc 53 0f 84 d3 00
 | 00 00 bf 01 00 00 00 e8 d0 a1 fc ff <49> 8b 84 24 50 02 00 00 65 48 ff 40 08 4c 8b 6d 08 0f 1f 44 00

so simply keep a local reference to the module owner and
use it later.

CC: Pavel Emelyanov <xemul@parallels.com>
CC: Jiri Slaby <jslaby@suse.cz>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Frank reports that after continuing in kgdb the RX stale event
doesn't occur until after the RX fifo is filled up with exactly
the amount of characters programmed for the RX watermark (in this
case it's 48). To read a single character from the uartdm
hardware we force a stale event so that any characters in the RX
packing buffer are flushed into the RX fifo immediately instead
of waiting for a stale timeout or for the fifo to fill. Forcing
that stale event asserts the stale interrupt but we never clear
that interrupt via UART_CR_CMD_RESET_STALE_INT in the polling
functions. So when kgdb continues the stale interrupt is left
pending in the hardware and we don't timeout with a stale event,
like we usually would if a user typed one character on the
console, until the reset stale interrupt and stale event commands
are sent. Frank could get things working again by running
handle_rx_dm(). By putting enough characters into the fifo he
could trigger a watermark interrupt, and thus cause
handle_rx_dm() to run finally resetting the stale interrupt
and enabling the stale event so that single characters would
cause timeouts again.

The fix is to just do what the interrupt routine was doing all
along and clear the stale interrupt and enable the event again.
Doing this also smooths over any differences in the fifo behavior
between v1.3 and v1.4 hardware allowing us to skip forcing the
uart into single character mode.

Reviewed-by: Frank Rowand <frank.rowand@sonymobile.com>
Tested-by: Frank Rowand <frank.rowand@sonymobile.com>
Fixes: f7e54d7a

 "msm_serial: Add support for poll_{get,put}_char()"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.

Found by using regex suggested by Joe Perches.

Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

CLPS711X serial driver uses the system wide registers to control the
modem signals. Now gpio-syscon driver can be used for this purposes.
mctrl_gpio helpers allow us to create GPIO bindings for any of modem/tty
control signals that extends the functionality of the driver.
This patch makes such change.

This change does not break any current DT bindings, since DT support
for this platform is not introduced yet.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

printk replaced with corresponding dev_* .
fixed two broken user-visible strings used by the corresponding printk.
the null check for uport->dev and port->dev is removed as dev_* will check for
null while printing.
printing of dev_name(uport->dev) and dev_name(port->dev) also removed as those
are being printed by dev_* .

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the of_device_id arrays const, as it is handled as const by all OF
functions.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixed below checkpatch.pl warning:

WARNING: void function return statements are not generally useful

Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixed below checkpatch.pl warning:

WARNING: else is not generally useful after a break or return

Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixed below checkpatch.pl warning:

WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ... then dev_err(dev, ... then pr_err(...  to printk(KERN_ERR ...

WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then dev_info(dev, ... then pr_info(...  to printk(KERN_INFO ...

Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes below checkpatch.pl warning and it remove extra blank lines:

WARNING: Missing a blank line after declarations

Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixed below checkpatch.pl warning:

WARNING: braces {} are not necessary for any arm of this statement

Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch lets you set the RS485 cappabilites of the device through
TIOCSRS485 and TIOCGRS485 as defined on Documentation/serial/serial-rs485.txt

In order to probe the device, the PNP id and the device id is used.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch allow the users of the 8250 infrastructure to define a
handler for RS485 configration.

If no handler is defined the 8250 driver will work as usual.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
--
v2:Change suggested by Alan "One Thousand Gnomes":
- Move rs485 structure further down on the uart_8250_port structure

 drivers/tty/serial/8250/8250_core.c | 39 +++++++++++++++++++++++++++++++++++++
 include/linux/serial_8250.h         |  3 +++
 2 files changed, 42 insertions(+)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Digi Neo cards are supported by the jsm driver.  Remove support
for these cards from dgnc.

Signed-off-by: Bill Pemberton <wfp5p@worldbroken.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add device ids for additional Neo cards.  The ids come from the dgnc
driver.

Signed-off-by: Bill Pemberton <wfp5p@worldbroken.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull Xtensa updates from Chris Zankel:
 "Xtensa improvements for 3.17:
   - support highmem on cores with aliasing data cache.  Enable highmem
     on kc705 by default
   - simplify addition of new core variants (no need to modify Kconfig /
     Makefiles)
   - improve robustness of unaligned access handler and its interaction
     with window overflow/underflow exception handlers
   - deprecate atomic and spill registers syscalls
   - clean up Kconfig: remove orphan MATH_EMULATION, sort 'select'
     statements
   - wire up renameat2 syscall.

  Various fixes:
   - fix address checks in dma_{alloc,free}_coherent (runtime BUG)
   - fix access to THREAD_RA/THREAD_SP/THREAD_DS (debug build breakage)
   - fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
     (runtime unrecoverable exception)
   - fix a6 and a7 handling in fast_syscall_xtensa (runtime userspace
     register clobbering)
   - fix kernel/user jump out of fast_unaligned (potential runtime
     unrecoverabl exception)
   - replace termios IOCTL code definitions with constants (userspace
     build breakage)"

* tag 'xtensa-20140830' of git://github.com/czankel/xtensa-linux: (25 commits)
  xtensa: deprecate fast_xtensa and fast_spill_registers syscalls
  xtensa: don't allow overflow/underflow on unaligned stack
  xtensa: fix a6 and a7 handling in fast_syscall_xtensa
  xtensa: allow single-stepping through unaligned load/store
  xtensa: move invalid unaligned instruction handler closer to its users
  xtensa: make fast_unaligned store restartable
  xtensa: add double exception fixup handler for fast_unaligned
  xtensa: fix kernel/user jump out of fast_unaligned
  xtensa: configure kc705 for highmem
  xtensa: support highmem in aliasing cache flushing code
  xtensa: support aliasing cache in kmap
  xtensa: support aliasing cache in k[un]map_atomic
  xtensa: implement clear_user_highpage and copy_user_highpage
  xtensa: fix TLBTEMP_BASE_2 region handling in fast_second_level_miss
  xtensa: allow fixmap and kmap span more than one page table
  xtensa: make fixmap region addressing grow with index
  xtensa: fix access to THREAD_RA/THREAD_SP/THREAD_DS
  xtensa: add renameat2 syscall
  xtensa: fix address checks in dma_{alloc,free}_coherent
  xtensa: replace IOCTL code definitions with constants
  ...

unicore32 builds fail with

  arch/unicore32/kernel/signal.c: In function ‘setup_frame’:
  arch/unicore32/kernel/signal.c:257: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c:279: error: ‘usig’ undeclared (first use in this function)
  arch/unicore32/kernel/signal.c: In function ‘handle_signal’:
  arch/unicore32/kernel/signal.c:306: warning: unused variable ‘tsk’
  arch/unicore32/kernel/signal.c: In function ‘do_signal’:
  arch/unicore32/kernel/signal.c:376: error: implicit declaration of function ‘get_signsl’
  make[1]: *** [arch/unicore32/kernel/signal.o] Error 1
  make: *** [arch/unicore32/kernel/signal.o] Error 2

Bisect points to commit 649671c9 ("unicore32: Use get_signal()
signal_setup_done()").

This code never even compiled.  Reverting the patch does not work, since
previously used functions no longer exist, so try to fix it up.  Compile
tested only.

Fixes: 649671c9

 ("unicore32: Use get_signal() signal_setup_done()")
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM fixes from Russell King:
 "Various assorted fixes:

   - a couple of patches from Mark Rutland to resolve an errata with
     Cortex-A15 CPUs.
   - fix cpuidle for the CPU part ID changes in the last merge window
   - add support for a relocation which ARM binutils is generating in
     some circumstances"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 8130/1: cpuidle/cpuidle-big_little: fix reading cpu id part number
  ARM: 8129/1: errata: work around Cortex-A15 erratum 830321 using dummy strex
  ARM: 8128/1: abort: don't clear the exclusive monitors
  ARM: 8127/1: module: add support for R_ARM_TARGET1 relocations

Pull ARM SoC fixes from Olof Johansson:
 "Here's the weekly batch of fixes from arm-soc.

  The delta is a largeish negative delta, due to revert of SMP support
  for Broadcom's STB SoC -- it was accidentally merged before some
  issues had been addressed, so they will make a new attempt for 3.18.
  I didn't see a need for a full revert of the whole platform due to
  this, we're keeping the rest enabled.

  The rest is mostly:

   - a handful of DT fixes for i.MX (Hummingboard/Cubox-i in particular)
   - some MTD/NAND fixes for OMAP
   - minor DT fixes for shmobile
   - warning fix for UP builds on vexpress/spc

  There's also a couple of patches that wires up hwmod on TI's DRA7 SoC
  so it can boot.  Drivers and the rest had landed for 3.17, and it's
  small and isolated so it made sense to pick up now even if it's not a
  bugfix"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
  vexpress/spc: fix a build warning on array bounds
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants
  MAINTAINERS: catch special Rockchip code locations
  ARM: dts: microsom-ar8035: MDIO pad must be set open drain
  ARM: dts: omap54xx-clocks: Fix the l3 and l4 clock rates
  ARM: brcmstb: revert SMP support
  ARM: OMAP2+: hwmod: Rearm wake-up interrupts for DT when MUSB is idled
  ARM: dts: Enable UART wake-up events for beagleboard
  ARM: dts: Remove twl6030 clk32g "regulator"
  ARM: OMAP2+: omap_device: remove warning that clk alias already exists
  ARM: OMAP: fix %d confusingly prefixed with 0x in format string
  ARM: dts: DRA7: fix interrupt-cells for GPIO
  mtd: nand: omap: Fix 1-bit Hamming code scheme, omap_calculate_ecc()
  ARM: dts: omap3430-sdp: Revert to using software ECC for NAND
  ARM: OMAP2+: GPMC: Support Software ECC scheme via DT
  mtd: nand: omap: Revert to using software ECC by default
  ARM: dts: hummingboard/cubox-i: change SPDIF output to be more descriptive
  ARM: dts: hummingboard/cubox-i: add USB OC pinctrl configuration
  ARM: shmobile: r8a7791: add missing 0x0100 for SDCKCR
  ...

With ARCH_VEXPRESS_SPC option, kernel build has the following
warning:

arch/arm/mach-vexpress/spc.c: In function ‘ve_spc_clk_init’:
arch/arm/mach-vexpress/spc.c:431:38: warning: array subscript is below array bounds [-Warray-bounds]
  struct ve_spc_opp *opps = info->opps[cluster];
                                      ^
since 'cluster' maybe '-1' in UP system. This patch does a active
checking to fix this issue.

Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into fixes

Pull "ARM: OMAP2+: DRA72x/DRA74x basic support" from Tony Lindgren:

Add basic subarchitecture support for the DRA72x and DRA74x.  These
are OMAP2+ derivative SoCs.  This should be low-risk to existing OMAP
platforms.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod-a-early-v3.17-rc/20140827194314/

* tag 'for-v3.17-rc/omap-dra72x-d74x-support-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending

:
  ARM: DRA7: hwmod: Add dra74x and dra72x specific ocp interface lists
  ARM: DRA7: Add support for soc_is_dra74x() and soc_is_dra72x() variants

Signed-off-by: Olof Johansson <olof@lixom.net>

Pull spi bugfixes from Mark Brown:
 "A smattering of bug fixes for the SPI subsystem, all in driver code
  which has seen active work recently and none of them with any great
  global impact.

  There's also a new ACPI ID for the pxa2xx driver which required no
  code changes and the addition of kerneldoc for some structure fields
  that were missing it and generating warnings during documentation
  builds as a result"

* tag 'spi-v3.17-rc3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: sh-msiof: Fix transmit-only DMA transfers
  spi/rockchip: Avoid accidentally turning off the clock
  spi: dw: fix kernel crash due to NULL pointer dereference
  spi: dw-pci: fix bug when regs left uninitialized
  spi: davinci: fix SPI_NO_CS functionality
  spi/rockchip: fixup incorrect dma direction setting
  spi/pxa2xx: Add ACPI ID for Intel Braswell
  spi: spi-au1550: fix build failure
  spi: rspi: Fix leaking of unused DMA descriptors
  spi: sh-msiof: Fix leaking of unused DMA descriptors
  spi: Add missing kerneldoc bits
  spi/omap-mcspi: Fix the spi task hangs waiting dma_rx

spi: Bug fixes for v3.17

A smattering of bug fixes for the SPI subsystem, all in driver code
which has seen active work recently and none of them with any great
global impact.

There's also a new ACPI ID for the pxa2xx driver which required no code
changes and the addition of kerneldoc for some structure fields that
were missing it and generating warnings during documentation builds as a
result.

# gpg: Signature made Sun 31 Aug 2014 13:19:12 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg:                 aka "Mark Brown <broonie@debian.org>"
# gpg:                 aka "Mark Brown <broonie@kernel.org>"
# gpg:                 aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg:                 aka "Mark Brown <broonie@linaro.org>"
# gpg:                 aka "Mark Brown <Mark.Brown@linaro.org>"

Fix tx/rx mixup, which broke transmit-only transfers.

Introduced by commit 4240305f7cbdc7782aa8bc40cc702775d9ac0839
("spi: sh-msiof: Fix leaking of unused DMA descriptors").

Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>

Pull file locking bugfx from Jeff Layton:
 "Just a bugfix for a bug that crept in to v3.15.  It's in a rather rare
  error path, and I'm not aware of anyone having hit it, but it's worth
  fixing for v3.17"

* tag 'locks-v3.17-3' of git://git.samba.org/jlayton/linux:
  locks: pass correct "before" pointer to locks_unlink_lock in generic_add_lease

Merge remote-tracking branches 'spi/fix/au1550', 'spi/fix/davinci', 'spi/fix/doc', 'spi/fix/dw', 'spi/fix/omap-mcspi', 'spi/fix/pxa2xx', 'spi/fix/rockchip' and 'spi/fix/rspi' into spi-linus

Pull x86 fixes from Peter Anvin:
 "One patch to avoid assigning interrupts we don't actually have on
  non-PC platforms, and two patches that addresses bugs in the new
  IOAPIC assignment code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86, irq, PCI: Keep IRQ assignment for runtime power management
  x86: irq: Fix bug in setting IOAPIC pin attributes
  x86: Fix non-PC platform kernel crash on boot due to NULL dereference

Pull ACPI and power management fixes from Rafael Wysocki:

 - Fix for an ACPI regression related to the handling of fixed events
   that caused netlink routines to be (incorrectly) run in interrupt
   context from Lan Tianyu

 - Fix for an ACPI EC driver regression on Acer Aspire V5-573G that
   caused AC/battery plug/unplug and video brightness change
   notifications to be delayed on that machine from Lv Zheng

 - Fix for an ACPI device enumeration regression that caused ACPI driver
   probe to fail for some devices where it succeeded before (Rafael J
   Wysocki)

 - intel_pstate driver fix to prevent it from printing an information
   message for every CPU in the system on every boot from Andi Kleen

 - s5pv210 cpufreq driver fix to remove an __init annotation from a
   routine that in fact can be called at any time after init too from
   Mark Brown

 - New Intel Braswell device ID for the ACPI LPSS (Low-Power Subsystem)
   driver from Alan Cox

 - New Intel Braswell CPU ID for intel_pstate from Mika Westerberg

* tag 'pm+acpi-3.17-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq: s5pv210: Remove spurious __init annotation
  cpufreq: intel_pstate: Add CPU ID for Braswell processor
  intel_pstate: Turn per cpu printk into pr_debug
  ACPI / LPSS: Add ACPI IDs for Intel Braswell
  ACPI / EC: Add support to disallow QR_EC to be issued before completing previous QR_EC
  ACPI / EC: Add support to disallow QR_EC to be issued when SCI_EVT isn't set
  ACPI: Run fixed event device notifications in process context
  ACPI / scan: Allow ACPI drivers to bind to PNP device objects

Merge patches from Andrew Morton:
 "22 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
  kexec: purgatory: add clean-up for purgatory directory
  Documentation/kdump/kdump.txt: add ARM description
  flush_icache_range: export symbol to fix build errors
  tools: selftests: fix build issue with make kselftests target
  ocfs2: quorum: add a log for node not fenced
  ocfs2: o2net: set tcp user timeout to max value
  ocfs2: o2net: don't shutdown connection when idle timeout
  ocfs2: do not write error flag to user structure we cannot copy from/to
  x86/purgatory: use approprate -m64/-32 build flag for arch/x86/purgatory
  drivers/rtc/rtc-s5m.c: re-add support for devices without irq specified
  xattr: fix check for simultaneous glibc header inclusion
  kexec: remove CONFIG_KEXEC dependency on crypto
  kexec: create a new config option CONFIG_KEXEC_FILE for new syscall
  x86,mm: fix pte_special versus pte_numa
  hugetlb_cgroup: use lockdep_assert_held rather than spin_is_locked
  mm/zpool: use prefixed module loading
  zram: fix incorrect stat with failed_reads
  lib: turn CONFIG_STACKTRACE into an actual option.
  mm: actually clear pmd_numa before invalidating
  memblock, memhotplug: fix wrong type in memblock_find_in_range_node().
  ...

Without this patch the kexec-purgatory.c and purgatory.ro files are not
removed after make mrproper.

Signed-off-by: Michael Welling <mwelling@ieee.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add arm specific parts to kdump kernel documentation.

Signed-off-by: Hu Keping <hukeping@huawei.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Haren Myneni <hbabu@us.ibm.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix building errors occuring due to a missing export of
flush_icache_range() in

kisskb.ellerman.id.au/kisskb/buildresult/11677809/

ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined!

Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>	[arc]
Acked-by: Richard Kuo <rkuo@codeaurora.org>	[hexagon]
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>	[xtensa]
Cc: Noam Camus <noamc@ezchip.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Zhigang Lu <zlu@tilera.com>		[tile]
Cc: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the typo of ARCH when running 'make kselftests'.  Change the 'X86'
to 'x86'.  Test by compilation.

Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For debug use, we can see from the log whether the fence decision is
made and why it is not fenced.

Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When tcp retransmit timeout(15mins), the connection will be closed.
Pending messages may be lost during this time.  So we set tcp user
timeout to override the retransmit timeout to the max value.  This is OK
for ocfs2 since we have disk heartbeat, if peer crash, the disk
heartbeat will timeout and it will be evicted, if disk heartbeat not
timeout and connection idle for a long time, then this means the cluster
enters split-brain state, since fence can't happen, we'd better keep the
connection and wait network recover.

Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Joseph Qi <joseph.qi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>