Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().

There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org

Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.

Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".

GEN_I chips don't have BM DMA, so no TRIM for them.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org

ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO.  Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD.  Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.

Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Commit d62f5576 (pata_cmd64x: fix handling of address setup timings)
incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading
to devide by zero fault.  Revert it until better fix is available.
This is reported in bko#16607 by Milan Kocian who also root caused it.

  https://bugzilla.kernel.org/show_bug.cgi?id=16607



Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-root-caused-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf, x86, Pentium4: Clear the P4_CCCR_FORCE_OVF flag
  tracing/trace_stack: Fix stack trace on ppc64

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  Eliminate sparse warning - bad constant expression
  cifs: check for NULL session password
  missing changes during ntlmv2/ntlmssp auth and sign
  [CIFS] Fix ntlmv2 auth with ntlmssp
  cifs: correction of unicode header files
  cifs: fix NULL pointer dereference in cifs_find_smb_ses
  cifs: consolidate error handling in several functions
  cifs: clean up error handling in cifs_mknod

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  MAINTAINERS: hwmon/coretemp: Change maintainers
  hwmon: (k8temp) Differentiate between AM2 and ASB1
  hwmon: (ads7871) Fix ads7871_probe error paths
  hwmon: (coretemp) Fix harmless build warning

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, tsc, sched: Recompute cyc2ns_offset's during resume from sleep states
  sched: Fix rq->clock synchronization when migrating tasks

* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
  xen: handle events as edge-triggered
  xen: use percpu interrupts for IPIs and VIRQs

* '2.6.36-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/xfsdev:
  xfs: do not discard page cache data on EAGAIN
  xfs: don't do memory allocation under the CIL context lock
  xfs: Reduce log force overhead for delayed logging
  xfs: dummy transactions should not dirty VFS state
  xfs: ensure f_ffree returned by statfs() is non-negative
  xfs: handle negative wbc->nr_to_write during sync writeback
  writeback: write_cache_pages doesn't terminate at nr_to_write <= 0
  xfs: fix untrusted inode number lookup
  xfs: ensure we mark all inodes in a freed cluster XFS_ISTALE
  xfs: unlock items before allowing the CIL to commit

Huaxu and Rudolf want me to be the hwmon coretemp driver maintainer and
remove their names from the coretemp maintainer entry.

Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Huaxu Wan <huaxu.wan@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.

The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.

This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).

Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

1. remove 'status' variable
2. remove unneeded initialization of 'err' variable
3. return missing error code if sysfs_create_group fail.
4. fix the init sequence as:
   - check hardware existence
   - kzalloc for ads7871_data
   - sysfs_create_group
   - hwmon_device_register

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Fix the following build warning:

  CC [M]  drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"

Introduced by commit 851b29cb

. When
you drop code, you also have to drop the variables this code was
using.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>

If on Pentium4 CPUs the FORCE_OVF flag is set then an NMI happens
on every event, which can generate a flood of NMIs. Clear it.

Reported-by: Vince Weaver <vweaver1@eecs.utk.edu>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

save_stack_trace() stores the instruction pointer, not the
function descriptor. On ppc64 the trace stack code currently
dereferences the instruction pointer and shows 8 bytes of
instructions in our backtraces:

 # cat /sys/kernel/debug/tracing/stack_trace
        Depth    Size   Location    (26 entries)
        -----    ----   --------
  0)     5424     112   0x6000000048000004
  1)     5312     160   0x60000000ebad01b0
  2)     5152     160   0x2c23000041c20030
  3)     4992     240   0x600000007c781b79
  4)     4752     160   0xe84100284800000c
  5)     4592     192   0x600000002fa30000
  6)     4400     256   0x7f1800347b7407e0
  7)     4144     208   0xe89f0108f87f0070
  8)     3936     272   0xe84100282fa30000

Since we aren't dealing with function descriptors, use %pS
instead of %pF to fix it:

 # cat /sys/kernel/debug/tracing/stack_trace
        Depth    Size   Location    (26 entries)
        -----    ----   --------
  0)     5424     112   ftrace_call+0x4/0x8
  1)     5312     160   .current_io_context+0x28/0x74
  2)     5152     160   .get_io_context+0x48/0xa0
  3)     4992     240   .cfq_set_request+0x94/0x4c4
  4)     4752     160   .elv_set_request+0x60/0x84
  5)     4592     192   .get_request+0x2d4/0x468
  6)     4400     256   .get_request_wait+0x7c/0x258
  7)     4144     208   .__make_request+0x49c/0x610
  8)     3936     272   .generic_make_request+0x390/0x434

Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: rostedt@goodmis.org
Cc: fweisbec@gmail.com
LKML-Reference: <20100825013238.GE28360@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  watchdog: Don't throttle the watchdog
  tracing: Fix timer tracing

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  mutex: Improve the scalability of optimistic spinning

pa-risc and ia64 have stacks that grow upwards. Check that
they do not run into other mappings. By making VM_GROWSUP
0x0 on architectures that do not ever use it, we can avoid
some unpleasant #ifdefs in check_stack_guard_page().

Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When converting this to the new wait_for macro I inverted the wait
condition, which causes all sorts of problems.  So correct it to fix
several failures caused by the bad wait (flickering, bad output
detection, tearing, etc.).

Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Xen events are logically edge triggered, as Xen only calls the event
upcall when an event is newly set, but not continuously as it remains set.
As a result, use handle_edge_irq rather than handle_level_irq.

This has the important side-effect of fixing a long-standing bug of
events getting lost if:
 - an event's interrupt handler is running
 - the event is migrated to a different vcpu
 - the event is re-triggered

The most noticable symptom of these lost events is occasional lockups
of blkfront.

Many thanks to Tom Kopec and Daniel Stodden in tracking this down.

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Tom Kopec <tek@acm.org>
Cc: Daniel Stodden <daniel.stodden@citrix.com>
Cc: Stable Kernel <stable@kernel.org>

IPIs and VIRQs are inherently per-cpu event types, so treat them as such:
 - use a specific percpu irq_chip implementation, and
 - handle them with handle_percpu_irq

This makes the path for delivering these interrupts more efficient
(no masking/unmasking, no locks), and it avoid problems with attempts
to migrate them.

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>

Eliminiate sparse warning during usage of crypto_shash_* APIs
       error: bad constant expression

Allocate memory for shash descriptors once, so that we do not kmalloc/kfree it
for every signature generation (shash descriptor for md5 hash).

From ed7538619817777decc44b5660b52268077b74f3 Mon Sep 17 00:00:00 2001
From: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Date: Tue, 24 Aug 2010 11:47:43 -0500
Subject: [PATCH] eliminate sparse warnings during crypto_shash_* APis usage

Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
  [S390] fix tlb flushing vs. concurrent /proc accesses
  [S390] s390: fix build error (sys_execve)

We should pass the data to the data register.

Signed-off-by: Jianwei Yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It looks like there is an off-by-one error in one of your changes to
drivers/staging/rar_register/rar_register.c:

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This build bug triggers:

 drivers/built-in.o: In function `mantis_exit':
 (.text+0x377413): undefined reference to `ir_input_unregister'
 drivers/built-in.o: In function `mantis_input_init':
 (.text+0x3774ff): undefined reference to `__ir_input_register'

If MANTIS_CORE is enabled but IR_CORE is not. Add the correct
dependency.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc64: Get rid of indirect p1275 PROM call buffer.
  sparc64: Fill a missing delay slot.
  sparc64: Make lock backoff really a NOP on UP builds.
  sparc64: simple microoptimizations for atomic functions
  sparc64: Make rwsems 64-bit.
  sparc64: Really fix atomic64_t interface types.

The tlb flushing code uses the mm_users field of the mm_struct to
decide if each page table entry needs to be flushed individually with
IPTE or if a global flush for the mm_struct is sufficient after all page
table updates have been done. The comment for mm_users says "How many
users with user space?" but the /proc code increases mm_users after it
found the process structure by pid without creating a new user process.
Which makes mm_users useless for the decision between the two tlb
flusing methods. The current code can be confused to not flush tlb
entries by a concurrent access to /proc files if e.g. a fork is in
progres. The solution for this problem is to make the tlb flushing
logic independent from the mm_users field.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
  powerpc: Fix config dependency problem with MPIC_U3_HT_IRQS
  via-pmu: Add compat_pmu_ioctl
  powerpc: Wire up fanotify_init, fanotify_mark, prlimit64 syscalls
  powerpc/pci: Fix checking for child bridges in PCI code.
  powerpc: Fix typo in uImage target
  powerpc: Initialise paca->kstack before early_setup_secondary
  powerpc: Fix bogus it_blocksize in VIO iommu code
  powerpc: Inline ppc64_runlatch_off
  powerpc: Correct smt_enabled=X boot option for > 2 threads per core
  powerpc: Silence xics_migrate_irqs_away() during cpu offline
  powerpc: Silence __cpu_up() under normal operation
  powerpc: Re-enable preemption before cpu_die()
  powerpc/pci: Drop unnecessary null test
  powerpc/powermac: Drop unnecessary null test
  powerpc/powermac: Drop unnecessary of_node_put
  powerpc/kdump: Stop all other CPUs before running crash handlers
  powerpc/mm: Fix vsid_scrample typo
  powerpc: Use is_32bit_task() helper to test 32 bit binary
  powerpc: Export memstart_addr and kernstart_addr on ppc64
  powerpc: Make rwsem use "long" type
  ...

fix this build error:
arch/s390/kernel/process.c:272: error: conflicting types for 'sys_execve'
arch/s390/kernel/entry.h:45: error: previous declaration of 'sys_execve' was here
make[1]: *** [arch/s390/kernel/process.o] Error 1
make: *** [arch/s390/kernel] Error 2

introduced by d7627467



Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: sep: remove driver
  Staging: batman-adv: Don't write in not allocated packet_buff
  Staging: batman-adv: Don't use net_dev after dev_put
  Staging: batman-adv: Create batman_if only on register event
  Staging: batman-adv: fix own mac address detection
  Staging: batman-adv: always reply batman icmp packets with primary mac
  Staging: batman-adv: fix batman icmp originating from secondary interface
  Staging: batman-adv: unify orig_hash_lock spinlock handling to avoid deadlocks
  Staging: batman-adv: Fix merge of linus tree
  Staging: spectra: removes unused functions
  Staging: spectra: initializa lblk variable
  Staging: spectra: removes unused variable
  Staging: spectra: remove duplicate GLOB_VERSION definition
  Staging: spectra: don't use locked_ioctl, fix build
  Staging: use new REQ_FLUSH flag, fix build breakage
  Staging: spectra: removes q->prepare_flush_fn, fix build breakage

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  68328serial: check return value of copy_*_user() instead of access_ok()
  synclink: add mutex_unlock() on error path
  rocket: add a mutex_unlock()
  ip2: return -EFAULT on copy_to_user errors
  ip2: remove unneeded NULL check
  serial: print early console device address in hex

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
  kobject_uevent: fix typo in comments
  firmware_class: fix typo in error path
  kobject: Break the kobject namespace defs into their own header

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
  ARM: imx: fix build failure concerning otg/ulpi
  USB: ftdi_sio: add product ID for Lenz LI-USB
  USB: adutux: fix misuse of return value of copy_to_user()
  USB: iowarrior: fix misuse of return value of copy_to_user()
  USB: xHCI: update ring dequeue pointer when process missed tds
  USB: xhci: Remove buggy assignment in next_trb()
  USB: ftdi_sio: Add ID for Ionics PlugComputer
  USB: serial: io_ti.c: don't return 0 if writing the download record failed
  USB: otg: twl4030: fix wrong assumption of starting state
  USB: gadget: Return -ENOMEM on memory allocation failure
  USB: gadget: fix composite kernel-doc warnings
  USB: ssu100: set tty_flags in ssu100_process_packet
  USB: ssu100: add disconnect function for ssu100
  USB: serial: export symbol usb_serial_generic_disconnect
  USB: ssu100: rework logic for TIOCMIWAIT
  USB: ssu100: add register parameter to ssu100_setregister
  USB: ssu100: remove duplicate #defines in ssu100
  USB: ssu100: refine process_packet in ssu100
  USB: ssu100: add locking for port private data in ssu100
  USB: r8a66597-udc: return -ENOMEM if kzalloc() fails
  ...

This is based upon a report by Meelis Roos showing that it's possible
that we'll try to fetch a property that is 32K in size with some
devices.  With the current fixed 3K buffer we use for moving data in
and out of the firmware during PROM calls, that simply won't work.

In fact, it will scramble random kernel data during bootup.

The reasoning behind the temporary buffer is entirely historical.  It
used to be the case that we had problems referencing dynamic kernel
memory (including the stack) early in the boot process before we
explicitly told the firwmare to switch us over to the kernel trap
table.

So what we did was always give the firmware buffers that were locked
into the main kernel image.

But we no longer have problems like that, so get rid of all of this
indirect bounce buffering.

Besides fixing Meelis's bug, this also makes the kernel data about 3K
smaller.

It was also discovered during these conversions that the
implementation of prom_retain() was completely wrong, so that was
fixed here as well.  Currently that interface is not in use.

Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>

MPIC_U3_HT_IRQS is selected both by PPC_PMAC64 and PPC_MAPLE, but depends
on PPC_MAPLE, so a PPC_PMAC64-only config gets this warning:

warning: (PPC_PMAC64 && PPC_PMAC && POWER4 || PPC_MAPLE && PPC64 && PPC_BOOK3S) selects MPIC_U3_HT_IRQS which has unmet direct dependencies (PPC_MAPLE)

Fix that by removing the dependency on PPC_MAPLE.

Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>