Add support for eint IRQ when MSDC is used as an SDIO host. This
feature requires SDIO device support async IRQ function. With this
feature, SDIO host can be awakened by SDIO card in suspend state,
without additional pin.

MSDC driver will time-share the SDIO DAT1 pin. During suspend, MSDC
turn off clock and switch SDIO DAT1 pin to GPIO mode. And during
resume, switch GPIO function back to DAT1 mode then turn on clock.

Some device tree property should be added or modified in MSDC node
to support SDIO eint IRQ. Pinctrls "state_eint" is mandatory. Since
this feature depends on asynchronous interrupts, "wakeup-source",
"keep-power-in-suspend" and "cap-sdio-irq" flags are necessary, and
the interrupts list should be extended(the interrupt named with
sdio_wakeup):
        &mmcX {
		...
		interrupt-names = "msdc", "sdio_wakeup";
		interrupts-extended = <...>,
                              	      <&pio xxx IRQ_TYPE_LEVEL_LOW>;
                ...
                pinctrl-names = "default", "state_uhs", "state_eint";
                ...
                pinctrl-2 = <&mmc2_pins_eint>;
                ...
                cap-sdio-irq;
		keep-power-in-suspend;
		wakeup-source;
                ...
        };

Co-developed-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-4-axe.yang@mediatek.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If wakeup-source flag is set in host dts node, parse EAI information
from SDIO CCCR interrupt externsion segment for in-band wakeup. If
async interrupt is supported by SDIO card then enable it and set
enable_async_irq flag in sdio_cccr structure to 1. The parse flow is
implemented in sdio_read_cccr().

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Link: https://lore.kernel.org/r/20220726062842.18846-3-axe.yang@mediatek.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Extend interrupts and pinctrls for SDIO wakeup interrupt feature.
This feature allow SDIO devices alarm asynchronous interrupt to host
even when host stop providing clock to SDIO card. An extra wakeup
interrupt and pinctrl states for SDIO DAT1 pin state switching are
required in this scenario.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Axe Yang <axe.yang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220726062842.18846-2-axe.yang@mediatek.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a compatible string for Rockchip RV1126 SoC.

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220723204335.750095-12-jagan@edgeble.ai


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The newest Gen3 SoCs and Gen4 SoCs do not need manual tap correction
with HS400 anymore. So, instead of checking the SDHI version, add a
quirk flag and set manual tap correction only for affected SoCs.

Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebased, renamed the quirk variable, removed stale comment]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220720072901.1266-1-wsa+renesas@sang-engineering.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In thunder_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.

Fixes: 166bac38 ("mmc: cavium: Add MMC PCI driver for ThunderX SOCs")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-2-windhl@126.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In octeon_mmc_probe(), we should call of_node_put() when breaking
out of for_each_child_of_node() which has increased and decreased
the refcount during each iteration.

Fixes: 01d95843 ("mmc: cavium: Add MMC support for Octeon SOCs.")
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Robert Richter <rric@kernel.org>
Link: https://lore.kernel.org/r/20220719095216.1241601-1-windhl@126.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In mmc_fixup_of_compatible_match(), we should call of_node_put()
when breaking out of for_each_child_of_node() which will increase
and decrease the refcount during one iteration.

Fixes: b360b110 ("mmc: core: allow to match the device tree to apply quirks")
Signed-off-by: Liang He <windhl@126.com>
Link: https://lore.kernel.org/r/20220719091051.1210806-1-windhl@126.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use clk_get_rate for base_clk on resume before setting new rate.
This change ensures that the clock api returns current rate
and sets the clock to the desired rate and honors CLK_GET_NO_CACHE
attribute used by clock api.

Fixes: 97904a59 (mmc: sdhci-brcmstb: Add ability to increase max clock rate for 72116b0)
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220714174132.18541-1-kdasu.kdev@gmail.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Document the compatible for SDHCI on SM8450.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220714123406.1919836-2-konrad.dybcio@somainline.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This reverts three commits:
1. Revert "mmc: sdhci-msm: Add compatible string check for sdx65"
   This reverts commit 95370684.

2. Revert "mmc: sdhci-msm: Add compatible string check for sm8150"
   This reverts commit 5acd6adb.

3. Revert "mmc: sdhci-msm: Add SoC specific compatibles"
   This reverts commit 466614a9.

The oldest commit 466614a9 ("mmc: sdhci-msm: Add SoC specific
compatibles") did not specify what benefits such multiple compatibles
bring, therefore assume there is none.  On the other hand such approach
brings a lot of churn to driver maintenance by expecting commit for
every new compatible, even though it is already covered by the fallback.

There is really no sense in duplicating of_device_id for each
variant, which is already covered by generic compatible fallback
qcom,sdhci-msm-v4 or qcom,sdhci-msm-v5.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220714091042.22287-4-krzysztof.kozlowski@linaro.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add a MSM8998-specific SDCC compatible, because using only a generic
qcom,sdhci-msm-v4 fallback is deprecated.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220714091042.22287-2-krzysztof.kozlowski@linaro.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Cards with 4k native sector size may only be read 4k-aligned,
accommodate for this in the single read recovery and use it.

Fixes: 81196976 (mmc: block: Add blk-mq support)
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Link: https://lore.kernel.org/r/cf4f316274c5474586d0d99b17db4a4c@hyperstone.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Merge the mmc fixes for v5.19rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v5.20.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use mmc_card_sdio macro to simplify code.

Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20220713033635.28432-3-sh043.lee@samsung.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add mmc_card_sd_combo() macro for sd combo type card and use the mmc_card_*
macro to simplify code instead of comparing card->type.

Signed-off-by: Seunghui Lee <sh043.lee@samsung.com>
Link: https://lore.kernel.org/r/20220713033635.28432-2-sh043.lee@samsung.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The entries in arrays must have fixed order, so the bindings and Linux
driver expecting various combinations of 'reg' addresses was never
actually conforming to guidelines.

The 'core' reg entry is valid only for SDCC v4 and lower, so disallow it
in SDCC v5.  SDCC v4 supports CQE and ICE, so allow them, even though
the qcom,sdhci-msm-v4 compatible is used also for earlier SoCs with SDCC
v2 or v3, so it is not entirely accurate.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220712144245.17417-3-krzysztof.kozlowski@linaro.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Bindings before conversion to DT schema expected reg-names without
"_mem" suffix.  This was used by older DTS files and by the MSM SDHCI
driver.

Reported-by: Douglas Anderson <dianders@chromium.org>
Fixes: edfbf8c307ff ("dt-bindings: mmc: sdhci-msm: Fix issues in yaml bindings")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20220712144245.17417-2-krzysztof.kozlowski@linaro.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

We need runtime PM enabled early in probe before sdhci_setup_host() for
sdhci_omap_set_capabilities(). But on the first runtime resume we must
not call sdhci_runtime_resume_host() as sdhci_setup_host() has not been
called yet. Let's check for an initialized controller like we already do
for context restore to fix a lockdep warning.

Fixes: f433e8aa ("mmc: sdhci-omap: Implement PM runtime functions")
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220622051215.34063-1-tony@atomide.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This commit adds dt-binding documentation of mmc for MediaTek MT8188 SoC
platform.

Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220708114747.13878-1-johnson.wang@mediatek.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Commit "mmc: sdhci-msm: Reset GCC_SDCC_BCR register for SDHC" added
support for utilizing a hardware reset and parsing it from DT, however
the bindings were not updated along with it.

So, document the usage of "resets" property with the limit of only one
item.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220704143554.1180927-1-robimarko@gmail.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In set_uhs_signaling, the DDR bit is being set by fully writing the MC1R
register.
This can lead to accidental erase of certain bits in this register.
Avoid this by doing a read-modify-write operation.

Fixes: d0918764 ("mmc: sdhci-of-at91: fix MMC_DDR_52 timing selection")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Karl Olsen <karl@micro-technic.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220630090926.15061-1-eugen.hristev@microchip.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SD_ROCR_S18A is already defined and is used to check the rocr value, so
let's replace with already defined values for readability.

Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220706004840.24812-1-cw9316.lee@samsung.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Convert the Samsung SoC SDHCI Controller bindings to DT schema.

The original bindings were quite old and incomplete, so add during
conversion typical (already used) properties like reg, clocks,
interrupts.

The bindings were not precising the clocks, although the upstream DTS
and Linux driver were expecting bus clocks in certain patterns in any
order.  Document the status quo even though it is not a proper approach
for bindings.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220626120342.38851-6-krzysztof.kozlowski@linaro.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If we reset because of an error, we need to preserve values for the
clock frequency. Otherwise, glitches may be seen on the bus.

To achieve that, we introduce a 'preserve' parameter to the reset
function and the IP core specific reset callbacks to handle everything
accordingly.

Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20220625131722.1397-1-wsa@kernel.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use bitmap_equal() instead of hand writing it. It improves semantic and
avoids some explicit computation to convert a number of bits to a number of
bytes.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b216df8798f765ab14bce65739c220643320f376.1656155715.git.christophe.jaillet@wanadoo.fr


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

'erased_blocks_bitmap' is never freed. As it is allocated at the same time
as 'used_blocks_bitmap', it is likely that it should be freed also at the
same time.

Add the corresponding bitmap_free() in msb_data_clear().

Fixes: 0ab30494 ("memstick: add support for legacy memorysticks")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/b3b78926569445962ea5c3b6e9102418a9effb88.1656155715.git.christophe.jaillet@wanadoo.fr


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Some functions of the bitmap API take advantage of the fact that a bitmap
is an array of long.

So, to make sure this assertion is correct, allocate bitmaps with
bitmap_zalloc() instead of kzalloc()+hand-computed number of bytes.

While at it, also use bitmap_free() instead of kfree() to keep the
semantic.

Fixes: 0ab30494 ("memstick: add support for legacy memorysticks")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dbf633c48c24ae6d95f852557e8d8b3bbdef65fe.1656155715.git.christophe.jaillet@wanadoo.fr


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Fix typo's,
* difference -> different
* alignment -> aligned

While at it updated the comment to make it clear that Renesas SDHI DMAC
needs buffers to be 128-byte aligned.

Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-3-prabhakar.mahadev-lad.rj@bp.renesas.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In case of devm_reset_control_get_optional_exclusive() failure we returned
directly instead of jumping to the error path to roll back initialization.

This patch moves devm_reset_control_get_optional_exclusive() early in the
probe so that we have the reset handle prior to initialization of the
hardware.

Fixes: b4d86f37 ("mmc: renesas_sdhi: do hard reset if possible")
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20220624181438.4355-2-prabhakar.mahadev-lad.rj@bp.renesas.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Callers of of_find_compatible_node() should drop the reference count
accordingly, so let's do that.

Signed-off-by: Liang He <windhl@126.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220621065259.4079817-1-windhl@126.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If CONFIG_PM is not set.

make ARCH=x86_64 CROSS_COMPILE=x86_64-linux-gnu-, will be failed, like this:

drivers/mmc/host/sdhci-pci-gli.c:834:13: error: ‘gl9763e_set_low_power_negotiation’ defined but not used [-Werror=unused-function]
 static void gl9763e_set_low_power_negotiation(struct sdhci_pci_slot *slot, bool enable)
             ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[3]: *** [drivers/mmc/host/sdhci-pci-gli.o] Error 1

To fix building warning, wrap all related code with CONFIG_PM.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ren Zhijie <renzhijie2@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220619104712.125364-1-renzhijie2@huawei.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If 'no-mmc' is set but 'no-mmc-hs400' is not, this warning is raised.
Specifying 'no-mmc' should be enough though.

Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220614113905.1458715-1-alexander.stein@ew.tq-group.com


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Due to flaws in hardware design, GL9763E takes long time to exit from L1
state. The I/O performance will suffer severe impact if it often enter and
exit L1 state during I/O requests.

To improve I/O read/write performance and take battery life into account,
let's turn on GL9763E L1 negotiation before entering runtime suspend and
turn off GL9763E L1 negotiation while executing runtime resume. That is to
say, GL9763E will not enter L1 state when executing I/O requests and enter
L1 state when PCIe bus idle.

Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20220613092907.2502-1-jason.lai@genesyslogic.com.tw


[Ulf: Improved the commit message a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)

So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.

This is a preparation for making platform remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-5-u.kleine-koenig@pengutronix.de


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_pltfm_unregister() returns 0 unconditionally and returning an
error in a platform remove callback isn't very sensible. (The only
effect of the latter is that the device core emits a generic warning and
then removes the device anyhow.)

So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.

This is a preparation for making platform remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220610211257.102071-4-u.kleine-koenig@pengutronix.de


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)

So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.

This is a preparation for making platform remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-3-u.kleine-koenig@pengutronix.de


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)

So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.

This is a preparation for making platform remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-2-u.kleine-koenig@pengutronix.de


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dw_mci_pltfm_remove() returns 0 unconditionally and returning an error
in a platform remove callback isn't very sensible. (The only effect of
the latter is that the device core emits a generic warning and then
removes the device anyhow.)

So return 0 unconditionally to make it obvious there is no error
forwarded to the upper layers.

This is a preparation for making platform remove callbacks return void.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220610211257.102071-1-u.kleine-koenig@pengutronix.de


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Clang warns a few times along the lines of:

  drivers/mmc/host/sdhci-brcmstb.c:302:6: warning: variable 'base_clk' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
          if (res)
              ^~~
  drivers/mmc/host/sdhci-brcmstb.c:376:24: note: uninitialized use occurs here
          clk_disable_unprepare(base_clk);
                                ^~~~~~~~

base_clk is used in the error path before it is initialized. Initialize
it to NULL, as clk_disable_unprepare() calls clk_disable() and
clk_unprepare(), which both handle NULL pointers gracefully.

Link: https://github.com/ClangBuiltLinux/linux/issues/1650


Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220608152757.82529-1-nathan@kernel.org


Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>