Add gta04a3 model with additional acceleromer.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch is preparation of adding more boards which have common moved
to omap3-gta04.dtsi. Other boards have only small additions to omap3-gta04a4.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define voltages and properties for various twl4030
regulators used on gta04 board.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define alias for lcd display present on gta04 board.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Because of commit: 3d495383


spi_gpio_pins node isn't valid anymore. Move to pmx_core2 node.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Define gpio node in tca6507 which will be used as
wifi reset pin.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

gta04 is using hmc5883l not hmc5843 so fix wrong compatible
entry.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the needed sections to enable nand support on
gta04 board.

Add nand partitions information.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board uses twl6040 codec connected via McPDM link. McBSP1 and McBSP2 can
be used for FM/BT.
At the same time move the pinctrl handling to the correct place - under the
corresponding nodes.
Audio connectors on the board:
Headset in/out
Stereo Line out
Stereo Line in.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The board uses twl6040 as audio codec. Move the corresponding  pinctrl as
well under the node.
twl6040 needs 32k clock from palams.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

clk32kg-audio clock is needed for twl6040 codec.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added dt data for PCIe controller. This node contains dt data for
both the DRA7 part of designware controller and for the designware core.
The documention for this node can be found @ ../bindings/pci/ti-pci.txt.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added dt data for PCIe PHY as a child node of ocp2scp3.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt.
26.3.3 PCIe Shared PHY Subsystem Integration in vE of DRA7xx ES1.0
describes the PCIe PHY subsystem-related components integrated in the device.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added dt data for PCIe PHY control module used by PCIe PHY.
The documention for this node can be found @ ../bindings/phy/ti-phy.txt

Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added missing clocks used by second instance of PCIe PHY.
The documention for this nodes can be found @ ../bindings/clock/ti/gate.txt.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There are two instances of PCIe PHY in DRA7xx. So renamed
optfclk_pciephy_32khz, optfclk_pciephy_clk and optfclk_pciephy_div_clk to
optfclk_pciephy1_32khz, optfclk_pciephy1_clk and optfclk_pciephy1_div_clk
respectively. This is needed for adding the clocks for second PCIe PHY
instance.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added missing 32KHz clock used by PCIe PHY.
Figure 26-19. PCIe PHY Subsystem Integration in vE of DRA7xx ES1.0 TRM shows
32KHz is used by PCIe PHY.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Change the parent of apll_pcie_in_clk_mux to dpll_pcie_ref_m2ldo_ck
from dpll_pcie_ref_ck.

Figure 26-22. DPLL_PCIE_REF Functional Block Diagram in vE of DRA7xx ES1.0 TRM
shows the signal name for the output of post divider (M2) is CLKOUTLDO.

Figure 26-21. PCIe PHY Clock Generator Overview shows CLKOUTLDO is used as
input to apll mux.

So the actual output of dpll is dpll_pcie_ref_m2ldo_ck which is also the input
of apll.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add divider table to optfclk_pciephy_div clock. The 8th bit of
CM_CLKMODE_APLL_PCIE can be programmed to either 0x0 or 0x1
based on if the divider value is 0x2 or 0x1.

Figure 26-21. PCIe PHY Clock Generator Overview in vE of DRA7xx ES1.0 shows the
block diagram of Clock Generator Subsystem of PCIe PHY module. The divider
value if '1' should be programmed in order to get the correct
PCIE_PHY_DIV_GCLK frequency (2.5GHz).

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The ldousb_reg regulator provides power to the USB1 and USB2
High Speed PHYs.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable TPS65218 config options.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix i2c nodes indentation.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add TPS65218 device tree nodes. i2c clock frequency setting
also added as part of tps65218 nodes addition. As i2c clock
enabling is required.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].

[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/



Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is a IRQ crossbar device in the soc, which
maps the irq requests from the peripherals to the
mpu interrupt controller's inputs. The Peripheral irq
requests are connected to only one crossbar
input and the output of the crossbar is connected to only one
controller's input line. The crossbar device is used to map
a peripheral input to a free mpu's interrupt controller line.

Here, adding a new crossbar device node and replacing all the peripheral
interrupt numbers with its fixed crossbar input lines.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

There is a IRQ crossbar device in the soc, which maps the
irq requests from the peripherals to the mpu interrupt
controller's inputs. The gic provides the support for such
IPs in the form of routable-irqs. So adding the property
here to gic node.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is no longer needed as clock data is provided through DT.

Signed-off-by: Tero Kristo <t-kristo@ti.com>

Otherwise legacy boot clock data is used. This patch also includes the
clock data files to the base dtsi files.

Signed-off-by: Tero Kristo <t-kristo@ti.com>

This patch adds support for initializing also omap2-prcm and omap2-scrm
through DT.

Signed-off-by: Tero Kristo <t-kristo@ti.com>

Cleans up the code a bit and is useful for clock data DT conversion.

Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add the necessary nodes to enable the LCD controller and the
LCD panel that is attached to the Texas Instruments AM335x
EVMSK platform.  Also setup the necessary pin mux within the
DT file to drive the LCD connector and add the correct
pinmux settings for the lcd pins to be configured to when
the SoC goes into sleep state for the minimum power
consumption.

For the sleep mode LCD pin settings, MUX_MODE7 is chosen as
this corresponds to switching the pins into input GPIO's with
an internal pulldown.  Which has been determined to offer the
lowest power solution vs leaving the pins configured in LCD
mode.

Signed-off-by: Darren Etheridge <detheridge@ti.com>
Acked-by: Wolfram Sang <wsa@sang-engineering.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

osc_ck can be simply defined as a multiplexer clock, and the sys_ck
can be a simple divider.

Signed-off-by: Tero Kristo <t-kristo@ti.com>

Add support for TI's AM437x StarterKit Evaluation
Module.

Cc: Josh Elliot <jelliott@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Franklin Cooper Jr. <fcooper@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

By providing labels for rtc, wdt, cpu and dispc nodes,
boards can access them to add board-specific data.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Franklin Cooper Jr. <fcooper@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

"make vdso_install" installs unstripped versions of the vdso objects
for the benefit of the debugger.  This was broken by checkin:

6f121e54

 x86, vdso: Reimplement vdso.so preparation in build-time C

The filenames are different now, so update the Makefile to cope.

This still installs the 64-bit vdso as vdso64.so.  We believe this
will be okay, as the only known user is a patched gdb which is known
to use build-ids, but if it turns out to be a problem we may have to
add a link.

Inspired by a patch from Sam Ravnborg.

Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/b10299edd8ba98d17e07dafcd895b8ecf4d99eff.1402586707.git.luto@amacapital.net


Signed-off-by: H. Peter Anvin <hpa@zytor.com>

The Go runtime has a buggy vDSO parser that currently segfaults.
This writes an empty SHT_DYNSYM entry that causes Go's runtime to
malfunction by thinking that the vDSO is empty rather than
malfunctioning by running off the end and segfaulting.

This affects x86-64 only as far as we know, so we do not need this for
the i386 and x32 vdsos.

Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/d10618176c4bd39b457a5e85c497295c90cab1bc.1402620737.git.luto@amacapital.net


Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Add PUT_LE() by analogy with GET_LE() to write littleendian values in
addition to reading them.

Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Link: http://lkml.kernel.org/r/3d9b27e92745b27b6fda1b9a98f70dc9c1246c7a.1402620737.git.luto@amacapital.net


Signed-off-by: H. Peter Anvin <hpa@zytor.com>

These defconfigs contain the CONFIG_M25P80 symbol, which is now
dependent on the MTD_SPI_NOR symbol. Add CONFIG_MTD_SPI_NOR to the
relevant defconfigs.

At the same time, drop the now-nonexistent CONFIG_MTD_CHAR symbol.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org