Add the initial device tree for the R8A7791 SoC based Henninger board. SCIF0
serial port support is included, so that the serial console can work.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use "sii,s35390a" instead of "seiko,s35390a", cfr.
Documentation/devicetree/bindings/i2c/trivial-devices.txt and
Documentation/devicetree/bindings/vendor-prefixes.txt.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
[horms+renesas@verge.net.au resolved conflicts]
[horms+renesas@verge.net.au consistently use space as separator]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

All I2C clocks derive from the HP clock, not from the P clock. Fix them.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

All I2C clocks derive from the HP clock, not from the P clock. Fix them.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The correct binding is "micrel,led-mode", not "led-mode".

This corrects an error which was introduced when setting of ethernet PHY
LED mode was added by 82e62182d59bd1d0 ("ARM: shmobile: lager: Set ethernet
PHY LED mode").

This makes the lager code consistent with the koelsch code which was added
by ae00d12a032490b3 ("ARM: shmobile: koelsch: Set ethernet PHY LED mode").

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This enables the Seiko real-time clock that is attached to a couple of
GPIO pins.

Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add support for EHCI clock gating via the MSTP703 bit on r8a7791.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add "renesas,*-r8a7740" to the compatible strings for consistency with other
devices.

Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This node should have a unique name so it can be distinguished when
other i2c busses are added later.

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Koelsch board uses the ethernet PHY LED0 as a link signal connected
to the ethernet controller. Specify the corresponding LED mode for the
PHY.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Lager board uses the ethernet PHY LED0 as a link signal connected to
the ethernet controller. Specify the corresponding LED mode for the PHY.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Koelsch board.
This makes the DT code match the legacy board code. Also
update the existing gpio-keys nodes to make use of KEY_n.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DTS gpio-keys support for SW2 on the Lager board.
This makes the DT code match the legacy board code.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add Spansion s25fl008k SPI FLASH and MTD partition, based on bockw legacy
board code.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

  - Add "renesas,hspi-r8a7779" compatible value,
  - Correct reference to parent interrupt controller
    (use "interrupt-parent" instead of "interrupt-controller"),
  - Add missing "#address-cells" and "#size-cells" properties, which are
    needed when populating the SPI buses.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

  - Add "renesas,hspi-r8a7778" compatible value,
  - Correct reference to parent interrupt controller
    (use "interrupt-parent" instead of "interrupt-controller"),
  - Add missing "#address-cells" and "#size-cells" properties, which are
    needed when populating the SPI buses.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Koelsch.
On this board, only MSIOF0 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add pinctrl and SPI device for MSIOF on Lager.
On this board, only MSIOF1 is in use. Its bus contains a single device
(a Renesas R2A11302FT PMIC), for which no bindings are defined yet.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi3.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Prepare for the advent of MSIOF SPI, which will be spi1 to spi4.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The correct maximum CPU frequency for r8a7791 is 1500 MHz
so update the r8a7791 SoC DTS to reflect this.

Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Commit 8f619b54

 ("powerpc/ppc64: Do not turn AIL (reloc-on
interrupts) too early") added code to set the AIL bit in the LPCR
without checking whether the kernel is running in hypervisor mode.  The
result is that when the kernel is running as a guest (i.e., under
PowerKVM or PowerVM), the processor takes a privileged instruction
interrupt at that point, causing a panic.  The visible result is that
the kernel hangs after printing "returning from prom_init".

This fixes it by checking for hypervisor mode being available before
setting LPCR.  If we are not in hypervisor mode, we enable relocation-on
interrupts later in pSeries_setup_arch using the H_SET_MODE hcall.

Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

using IS_ENABLED() macro instead of defined(CONFIG_XXX) || defined(CONFIG_XXX_MODULE)

Signed-off-by: Steven Miao <realmz6@gmail.com>

Signed-off-by: Steven Miao <realmz6@gmail.com>

In v3.2 the Analog Devices ADT75 temperature sensor driver was removed
as an IIO driver and support for it was added to the LM75 HWMON driver.
But it was apparently overlooked to rename one reference to CONFIG_ADT75
to CONFIG_SENSORS_LM75. Do so now. Use the IS_ENABLED() macro, while
we're at it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

In v3.2 the Analog Devices AD7314 temperature sensor driver was removed
as an IIO driver and added as a HWMON driver. But it was apparently
overlooked to rename two references to CONFIG_AD7314 to
CONFIG_SENSORS_AD7314. Do so now. Use the IS_ENABLED() macro, while
we're at it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

In v3.2 the Analog Devices ad2s1200/ad2s1205 driver was renamed from
ad2s120x to ad2s1200. But it apparently forgot to rename the references
to this driver in the BF537-STAMP code. Rename these now, and use the
IS_ENABLED() macro, while we're at it.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

There's a (rather subtle) typo in "CONFIG_SND_SOC_ADV80X_MODULE". Fix it
once and for all by using IS_ENABLED(), which is designed to avoid
issues like this.

Signed-off-by: Paul Bolle <pebolle@tiscali.nl>

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>