Software must explicitely re-enable extended firmware tracing
after any ISP abort condition.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only.  If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).

The fix is relatively straightforward, drop the FCP_TARGET-only
check.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

There's a problem where sg is executing a ->nopage operation on a
compound page, it actually calls get_page() on the first page in the
compound rather than the page which is being mapped.  The fix is to
select the correct page by indexing into the compound.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Change version number to 8.1.9

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Stall error handler if attempting resets/aborts while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.

Background:
  Although the transport is using the scsi_timed_out functionality to
  restart the timeout if the rport is blocked, if the timeout has already
  fired before the block occurs, the eh handler still runs and can take
  the device offline. Ultimately, this window cannot be resolved without
  significant work in the error handler thread. Christoph noted the first
  level of these issues when he noted the poor error response handling
  by the error thread.

  We found, under heavy load and error testing, that time window from when
  the scsi_times_out() adds the io to the queue to when the scsi_error_handler
  gets around to servicing it, can be in the several seconds range. In most
  cases, these test conditions are highly unusual, but possible.
  As a result, we're stalling the error handler in this race window so that
  we can avoid the device_offline transitions.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Misc Bug Fixes:
- Cap MBX_DOWN_LINK command timeout to 60 seconds
- Fix double free of ndlp object
- Don't free mbox structures on error. The completion handlers expect to do so.
- Clear host attention work items when going offline
- Fixed discovery issues in multi-initiator environments.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

This patch corrects a problem in mptfc which can result in targets
being removed after executing an "lsiutil 99" reset of the fibre
channel ports.

The last rescan event was being processed before the setup reset work
due to an inappropriate optimization in the event processing logic.
Every rescan event is now queued for execution and the setup reset
work now executes in the proper sequence.

Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Based upon a conversation I had with LSI's fibre channel firmware guru,
this patch adds another condition under which the driver waits for the
firmware link initialization / target discovery to complete.

Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Moore, Eric <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

The hptiop just got merged with a horrible amount of really bad ioctl
code that is against the standards for new scsi drivers.  This patch
backs it out (and fixes a small bug where scsi_add_host is called to
early).  We can re-add proper APIs once we agree on them.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Conflicts:

	arch/ia64/hp/sim/simscsi.c

Stylistic differences in two separate fixes for buffer->request_buffer
problem.

Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

New version number fo zfcp driver.

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Bug fixes for zfcp's erp:
- trigger adapter reopen if do_QDIO fails
- avoid erp deadlock if registration of scsi target or remote port hang
- do not treat as error if exchange port data fails
- decrease timeout for target reset and aborts
- mark unit failed if slave_destroy is called

Additionally some code cleanup was done:
- made some functions void when retval is not of interest
- shortened initialization of zfcp's host_template
- corrected some comments

Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Improve request handling. Use hash table to manage request IDs.

Signed-off-by: Volker Sameske <sameske@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Currently it is impossible to reset provided by Qlogic QLA2xxx driver
SCSI devices externally using corresponding sg devices, particularly via
sg_reset utility, because qla2xxx driver in qla2xxx_eh_device_reset()
function checks if the input scsi_cmnd has its private data (CMD_SP())
attached. Then the found pointer isn't used anywhere inside of
qla2xxx_eh_device_reset(). If the RESET request comes from sg device, it
doesn't have such private data.

The attached patch removes check for non-NULL CMD_SP() from
qla2xxx_eh_device_reset(), hence allows to reset QLA2xxx's devices using
corresponding sg devices.

AV: change applies to bus/host reset handlers as well.

Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Change version number to 8.1.8

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

ID String and Message fixes
 - Fix switch symbolic name registration to match cross-OS values
 - Replace printk's with more standard lpfc_printf_log calls
 - Make all lpfc_printf_log message numbers unique

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Short bug fixes:
 - Fix iocbq list corruption due to missing list_del's in ct handling
 - Missing unlock in lpfc_sli_next_iotag()
 - Fix initialization of can_queue value
 - Differentiate sysfs mailbox errors with different codes.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Fix race condition between lpfc_sli_issue_mbox and lpfc_online

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Fix failing firmware download due to mailbox delays needing to be longer.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>

* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/dtor/input: (24 commits)
  Input: ati_remote - use msec instead of jiffies
  Input: ati_remote - add missing input_sync()
  Input: ati_remote - relax permissions sysfs module parameters
  Input: ati_remote - make filter time a module parameter
  Input: atkbd - restore repeat rate when resuming
  Input: trackpoint - activate protocol when resuming
  Input: logips2pp - fix button mapping for MX300
  Input: keyboard - change to use kzalloc
  Input: serio/gameport - check whether driver core calls succeeded
  Input: spaceball - make 4000FLX Lefty work
  Input: keyboard - simplify emulate_raw() implementation
  Input: keyboard - remove static variable and clean up initialization
  Input: hiddev - use standard list implementation
  Input: add missing handler->start() call
  Input: HID - fix potential out-of-bound array access
  Input: fix list iteration in input_release_device()
  Input: iforce - add Trust Force Feedback Race Master support
  Input: iforce - check array bounds before accessing elements
  Input: libps2 - warn instead of oopsing when passed bad arguments
  Input: fm801-gp - fix use after free
  ...

* master.kernel.org:/pub/scm/linux/kernel/git/perex/alsa:
  [ALSA] Don't reject O_RDWR at opening PCM OSS with read/write-only device
  [ALSA] snd-emu10k1: Implement support for Audigy 2 ZS [SB0353]
  [ALSA] add MAINTAINERS entry for snd-aoa
  [ALSA] aoa: platform function gpio: ignore errors from functions that don't exist
  [ALSA] make snd-powermac load even when it can't bind the device
  [ALSA] aoa: fix toonie codec
  [ALSA] aoa: feature gpio layer: fix IRQ access
  [ALSA] Conversions from kmalloc+memset to k(z|c)alloc
  [ALSA] snd-emu10k1: Fixes ALSA bug#2190

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [LAPB]: Fix windowsize check
  [TCP]: Fixes IW > 2 cases when TCP is application limited
  [PKT_SCHED] RED: Fix overflow in calculation of queue average
  [LLX]: SOCK_DGRAM interface fixes
  [PKT_SCHED]: Return ENOENT if qdisc module is unavailable
  [BRIDGE]: netlink status fix

While busy-waiting for completion, check the hardware after scheduling;
don't schedule and then immediately check the _timeout_.  If the yield()
took a long time (as it does on my OLPC prototype board when it's busy),
we'd report a timeout even though the hardware was now ready.

This fixes it, and also switches the yield() for a cond_resched() because
we don't actually want to be _that_ nice about it.  I see nice
tightly-packed SMBus transactions now, rather than waiting for milliseconds
between successive phases.

Actually, we shouldn't be busy-waiting here at all.  We should be using
interrupts.  That's an exercise for another day though.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Cc: Christer Weinigel <wingel@nano-system.com>
Cc: <Jordan.Crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

I saw an oops down this path when trying to create a new file on a UDF
filesystem which was internally marked as readonly, but mounted rw:

udf_create
        udf_new_inode
                new_inode
                        alloc_inode
                        	udf_alloc_inode
                udf_new_block
                        returns EIO due to readonlyness
                iput (on error)
                        udf_put_inode
                                udf_discard_prealloc
                                        udf_next_aext
                                                udf_current_aext
                                                        udf_get_fileshortad
                                                                OOPS

the udf_discard_prealloc() path was examining uninitialized fields of the
udf inode.

udf_discard_prealloc() already has this code to short-circuit the discard
path if no extents are preallocated:

        if (UDF_I_ALLOCTYPE(inode) == ICBTAG_FLAG_AD_IN_ICB ||
                inode->i_size == UDF_I_LENEXTENTS(inode))
        {
                return;
        }

so if we initialize UDF_I_LENEXTENTS(inode) = 0 earlier in udf_new_inode,
we won't try to free the (not) preallocated blocks, since this will match
the i_size = 0 set when the inode was initialized.

Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The recent fixups in futex.c need to be applied to futex_compat.c too.  Fixes
a hang reported by Olaf.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

A patch in -mm kernel correct the parsing of "address resources" of pnpacpi.
Before we assumed it was memory only, but it could be also IO.

But this change show an hidden bug : some resources could be producer type
that are not handled by pnp layer.  So we should ignore the producer
resources.

This patch fixes bug 6292 (http://bugzilla.kernel.org/show_bug.cgi?id=6292

).
Some devices like PNP0A03 have 0xd00-0xffff and 0x0-0xcf7 as IO producer
resources.

Before correcting "address resources" parsing, it was seen as memory and was
harmless, because nobody tried to reserve this memory range as it should be
IO.

With the correction it become IO resources, and make failed all others device
that want to register IO in this range and use pnp layer (like a ISA sound
card).

The solution is to ignore producer resources

Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: Uwe Bugla <uwe.bugla@gmx.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: "Brown, Len" <len.brown@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

reiserfs_write_full_page does zero bytes in the file past eof, but it may
call get_block on those buffers as well.  On machines where the page size
is larger than the blocksize, this can result in mmaped files incorrectly
growing up to a block boundary during writepage.

The fix is to avoid calling get_block for any blocks that are entirely past
eof

Signed-off-by: Chris Mason <mason@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The correct lock ordering is inode lock -> BKL

Signed-off-by: Chris Mason <mason@suse.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch is for collision check enhancement for memory hot add.

It's better to do resouce collision check before doing memory hot add,
which will touch memory management structures.

And add_section() should check section exists or not before calling
sparse_add_one_section(). (sparse_add_one_section() will do another
check anyway. but checking in memory_hotplug.c will be easy to understand.)

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: keith mannthey <kmannth@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

both of acpi_memory_enable_device() and acpi_memory_add_device() may evaluate
_CRS method.

We should avoid evaluate device's resource twice if we could get it
successfully in past.

Signed-off-by: KAMEZWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

add_memory() does all necessary check to avoid collision.  then, acpi layer
doesn't have to check region by itself.

(*) pfn_valid() just returns page struct is valid or not. It returns 0
    if a section has been already added even is ioresource is not added.
    ioresource collision check in mm/memory_hotplug.c can do more precise
    collistion check.
    added enabled bit check just for sanity check..

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

find_next_system_ram() is used to find available memory resource at onlining
newly added memory.  This patch fixes following problem.

find_next_system_ram() cannot catch this case.

Resource:      (start)-------------(end)
Section :                (start)-------------(end)

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

find_next_system_ram() returns valid memory range which meets requested area,
only used by memory-hot-add.

This function always rewrite requested resource even if returned area is not
fully fit in requested one.  And sometimes the returnd resource is larger than
requested area.  This annoyes the caller.  This patch changes the returned
value to fit in requested area.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

ioresouce handling code in memory hotplug allows not-aligned memory hot add.
But when memmap and other memory structures are initialized, parameters should
be aligned.  (if not aligned, initialization of mem_map will do wrong, it
assumes parameters are aligned.) This patch fix it.

And this patch allows ioresource collision check to handle -EEXIST.

Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Keith Mannthey <kmannth@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

In bugzilla #6941, Jens Kilian reported:

"The function befs_utf2nls (in fs/befs/linuxvfs.c) writes a 0 byte past the
end of a block of memory allocated via kmalloc(), leading to memory
corruption.  This happens only for filenames which are pure ASCII and a
multiple of 4 bytes in length.  [...]

Without DEBUG_SLAB, this leads to further corruption and hard lockups; I
believe this is the bug which has made kernels later than 2.6.8 unusable
for me.  (This must be due to changes in memory management, the bug has
been in the BeFS driver since the time it was introduced (AFAICT).)

Steps to reproduce:
Create a directory (in BeOS, naturally :-) with files named, e.g.,
"1", "22", "333", "4444", ...  Mount it in Linux and do an "ls" or "find""

This patch implements the suggested fix. Credits to Jens Kilian for
debugging the problem and finding the right fix.

Signed-off-by: Diego Calleja <diegocg@gmail.com>
Cc: Jens Kilian <jjk@acm.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

At least Maxtor OneTouch III require a "start stop unit" command after auto
spin-down before the next access can proceed.  This patch activates the
responsible code in scsi_mod for all Maxtor SBP-2 disks.
https://bugzilla.novell.com/show_bug.cgi?id=183011



Maybe that should be done for all SBP-2 disks, but better be cautious.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Jody McIntyre <scjody@modernduck.com>
Cc: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>