The Lenovo Iomega ix4-300d is a 4-Bay sata NAS with dual Gb, USB2.0 & 3.0,
powered by a Marvell Armada XP MV78230 dual core CPU.

http://shop.lenovo.com/us/en/servers/network-storage/lenovoemc/ix4-300d/



Signed-off-by: Benoit Masson <yahoo@perenite.com>
Link: https://lkml.kernel.org/r/1406503839-4662-1-git-send-email-yahoo@perenite.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Add the DT fragment for the Marvell Dove LCD controllers.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/E1XAKGS-0004WE-8h@rmk-PC.arm.linux.org.uk


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

In Armada 375 SoCs, the MDIO is handled by a separate orion-mdio driver,
despite the register is contained within the "LMS" block of the network
controller.

Therefore we need to add the clock to the MDIO devicetree to prevent the
controller from being accesed with its clock gated. This is needed, for
instance, to be able to load the MDIO driver before the network driver.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1405961296-5846-7-git-send-email-ezequiel.garcia@free-electrons.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The vendor bootloader provided for Armada 375 boards expect an
alias for the ethernet nodes, which is used to fixup the MAC address.

Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lkml.kernel.org/r/1405961296-5846-6-git-send-email-ezequiel.garcia@free-electrons.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

In order to support dynamic frequency scaling:

 * the cpuclk Device Tree node needs to be updated to describe a
   second set of registers describing the PMU DFS registers.

 * the clock-latency property of the CPUs must be filled, otherwise
   the ondemand and conservative cpufreq governors refuse to work. The
   latency is high because the cost of a frequency transition is quite
   high on those CPUs.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1404920715-19834-5-git-send-email-thomas.petazzoni@free-electrons.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The CA9 MPcore SoC Control block is a set of registers that allows to
configure certain internal aspects of the core blocks of the SoC
(Cortex-A9, L2 cache controller, etc.). In most cases, the default
values are fine so they aren't many reasons to touch those registers,
but there is one exception: to support cpuidle on Armada 38x, we need
to modify the value of the CA9 MPcore Reset Control register.

Therefore, this commit adds a new Device Tree binding for this
hardware block, and uses this new binding for the Armada 38x Device
Tree file.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: devicetree@vger.kernel.org
Link: https://lkml.kernel.org/r/1404913221-17343-11-git-send-email-thomas.petazzoni@free-electrons.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This commit enables the network controller in the Armada 375 DB board,
and configures the two available ethernet interfaces.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1405021936-28658-4-git-send-email-ezequiel.garcia@free-electrons.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This commit adds the support for the network controller in Marvell
Armada 375 SoC devicetree.

Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1405021936-28658-3-git-send-email-ezequiel.garcia@free-electrons.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds DT support for the LaCie NAS d2 Network v2 (d2net_v2).
Most of the hardware characteristics are shared with the 2Big and 5Big
Network v2 boards.

- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-3-git-send-email-simon.guinot@sequanux.org


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The d2 Network v2 board (d2net_v2) shares a lot of hardware
characteristics with the 2Big and 5Big Network v2 boards. This patch
prepares the kirkwood-netxbig.dtsi file in order to allow to include it
from the d2net_v2 DTS file. The DT nodes only relevant for the 2Big and
5Big Network v2 boards are moved into their respective DTS files.

Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1404830545-15581-2-git-send-email-simon.guinot@sequanux.org


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Late correction from Simon's testing.

Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Link: https://lkml.kernel.org/r/20140621095001.GW20207@kw.sim.vm.gnt


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

As Mainlining effort for SolidRun CuBox has been carried out on the
Engineering Sample, the board DTS was reflecting this. Actually,
SolidRun CuBox comes in three different variants:
Engineering Sample (ES), production with 1GB RAM (1G),
and production with 2GB RAM (2G).

Therefore, we base current dove-cubox.dts on to the 1G production
variant and add a ES dts to add required quirk for misrouted SDHCI
card detect on top of dove-cubox.dts. For the 2G variant we rely on
the bootloader to setup correct RAM size.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Link: https://lkml.kernel.org/r/1401228006-3212-1-git-send-email-sebastian.hesselbarth@gmail.com


Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Describe LaCie 2Big and 5Big Network v2 using device tree.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1401132591-26305-3-git-send-email-andrew@lunn.ch


Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

OMAP5432, DRA75x and DRA72x have MPU DPLLs that need Duty Cycle
Correction(DCC) to operate safely at frequencies >= 1.4GHz.

Switch to "ti,omap5-mpu-dpll-clock" compatible property which provides
this support.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>

Adds HDMI audio sDMA properties.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Adds HDMI audio sDMA properties.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add the necessary DTS nodes to enable the micro-HDMI output on Parlor
board.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Alto35 expansion board has a ZIF connector for a 3.5'' LCD.
Add a common include file for this configuration, and use it
on Alto35.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector
for a 4.3'' LCD. Add a common include file for this configuration, and
use it on relevant expansion boards.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Summit and Tobi expansion boards have a HDMI connector with a TFP410
encoder. Add a common include file for this configuration, and then
use it for Summit and Tobi.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Looks like quite a few omap3 boards have sharp ls037v7dw01 that's
configured as various panel dpi entries for whatever legacy reasons.
For device tree based support, let's just configure these properly for
panel ls037v7dw01 instead of panel dpi.

This patch creates a common file for panel ls037v7dw01, and makes
boards ldp and omap3-evm to use it.

The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen
controller for the omaps, so let's add a basic configuration for
the touchscreen also using the default values.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>

This patch add support for lcd display on gta04 board. Display control
is connected to spi (used spi bitbang driver).

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

omap5-uevm has a single HDMI output. Add the necessary display
information, including pinmuxing.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

omap5-uevm has a tca6424a I/O expander. Add it to the .dts file.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add OMAP5 DSS nodes to omap5.dtsi.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for am43x-epos-evm's LCD panel.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for am437x-gp-evm's LCD panel.

Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for the display subsystem for AM4372. The DSS on AM4372 is
basically OMAP3's DSS, without DSI and VENC blocks.

Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Arndale-Octa board is always configured to work with trustzone
firmware binary. Added DTS node entry to enable this support.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch add pmusysreg node for Exynos3250 to access PMU
(Power Management Unit) register in a centralized way using
syscon driver.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.

Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The vbus-supply property is wrongly updated in the
usbdrd node instead of the usbdrd_phy node. This patch
fixes the same.

Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add initial device tree nodes for EXYNOS5410 SoC and SMDK5410 board.

Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds new exynos3250.dtsi to support Exynos3250 SoC
based on Cortex-A7 dual core and includes following dt nodes:

- GIC interrupt controller
- Pinctrl to control GPIOs
- Clock controller
- CPU information (Cortex-A7 dual core)
- UART to support serial port
- MCT (Multi Core Timer)
- ADC (Analog Digital Converter)
- I2C/SPI bus
- Power domain
- PMU (Performance Monitoring Unit)
- MSHC (Mobile Storage Host Controller)
- PWM (Pluse Width Modulation)
- AMBA bus
- sysram node for SYSRAM memory mapping

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hyunhee Kim <hyunhee.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: devicetree@vger.kernel.org
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds the mfc node to exynos5800 which uses MFCv8.

Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add required fixed-regulator for VBUS supply for USB 3.0
controller phy.

Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable FIMD for peach-pi board.

Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable display controller with timing information for 1080p
panel in Exynos5800 peach-pi board.

Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enable hdmi for peach-pi board.

Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds support for google peach-pi board having the
Exynos5800 SoC.

Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>