Skip to content
  1. Oct 20, 2021
    • Kurt Kanzenbach's avatar
      net: stmmac: Fix E2E delay mechanism · 3cb95802
      Kurt Kanzenbach authored 
      When utilizing End to End delay mechanism, the following error messages show up:

|root@ehl1:~# ptp4l --tx_timestamp_timeout=50 -H -i eno2 -E -m
|ptp4l[950.573]: selected /dev/ptp3 as PTP clock
|ptp4l[950.586]: port 1: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[950.586]: port 0: INITIALIZING to LISTENING on INIT_COMPLETE
|ptp4l[952.879]: port 1: new foreign master 001395.fffe.4897b4-1
|ptp4l[956.879]: selected best master clock 001395.fffe.4897b4
|ptp4l[956.879]: port 1: assuming the grand master role
|ptp4l[956.879]: port 1: LISTENING to GRAND_MASTER on RS_GRAND_MASTER
|ptp4l[962.017]: port 1: received DELAY_REQ without timestamp
|ptp4l[962.273]: port 1: received DELAY_REQ without timestamp
|ptp4l[963.090]: port 1: received DELAY_REQ without timestamp

Commit f2fb6b62 ("net: stmmac: enable timestamp snapshot for required PTP
packets in dwmac v5.10a") already addresses this problem for the dwmac
v5.10. However, same holds true for all dwmacs above version v4.10. Correct the
check accordingly. Afterwards everything works as expected.

Tested on Intel Atom(R) x6414RE Processor.

Fixes: 14f34733 ("net: stmmac: Correctly take timestamp for PTPv2")
Fixes: f2fb6b62

 ("net: stmmac: enable timestamp snapshot for required PTP packets in dwmac v5.10a")
Suggested-by: default avatarOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: default avatarKurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      3cb95802
    • Uwe Kleine-König's avatar
      nfc: st95hf: Make spi remove() callback return zero · 641e3fd1
      Uwe Kleine-König authored 
      

If something goes wrong in the remove callback, returning an error code
just results in an error message. The device still disappears.

So don't skip disabling the regulator in st95hf_remove() if resetting
the controller via spi fails. Also don't return an error code which just
results in two error messages.

Signed-off-by: default avatarUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: default avatarKrzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      641e3fd1
    • David S. Miller's avatar
      Merge branch 'hns3-fixes' · 323e9a95
      David S. Miller authored 
      

Guangbin Huang says:

====================
net: hns3: add some fixes for -net

This series adds some fixes for the HNS3 ethernet driver.
====================

Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      323e9a95
    • Peng Li's avatar
      net: hns3: disable sriov before unload hclge layer · 0dd8a25f
      Peng Li authored 
      HNS3 driver includes hns3.ko, hnae3.ko and hclge.ko.
hns3.ko includes network stack and pci_driver, hclge.ko includes
HW device action, algo_ops and timer task, hnae3.ko includes some
register function.

When SRIOV is enable and hclge.ko is removed, HW device is unloaded
but VF still exists, PF will not reply VF mbx messages, and cause
errors.

This patch fix it by disable SRIOV before remove hclge.ko.

Fixes: e2cb1dec

 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: default avatarPeng Li <lipeng321@huawei.com>
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      0dd8a25f
    • Yufeng Mo's avatar
      net: hns3: fix vf reset workqueue cannot exit · 1385cc81
      Yufeng Mo authored 
      The task of VF reset is performed through the workqueue. It checks the
value of hdev->reset_pending to determine whether to exit the loop.
However, the value of hdev->reset_pending may also be assigned by
the interrupt function hclgevf_misc_irq_handle(), which may cause the
loop fail to exit and keep occupying the workqueue. This loop is not
necessary, so remove it and the workqueue will be rescheduled if the
reset needs to be retried or a new reset occurs.

Fixes: 1cc9bc6e

 ("net: hns3: split hclgevf_reset() into preparing and rebuilding part")
Signed-off-by: default avatarYufeng Mo <moyufeng@huawei.com>
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      1385cc81
    • Yunsheng Lin's avatar
      net: hns3: schedule the polling again when allocation fails · 68752b24
      Yunsheng Lin authored 
      Currently when there is a rx page allocation failure, it is
possible that polling may be stopped if there is no more packet
to be reveiced, which may cause queue stall problem under memory
pressure.

This patch makes sure polling is scheduled again when there is
any rx page allocation failure, and polling will try to allocate
receive buffers until it succeeds.

Now the allocation retry is added, it is unnecessary to do the rx
page allocation at the end of rx cleaning, so remove it. And reset
the unused_count to zero after calling hns3_nic_alloc_rx_buffers()
to avoid calling hns3_nic_alloc_rx_buffers() repeatedly under
memory pressure.

Fixes: 76ad4f0e

 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: default avatarYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      68752b24
    • Yunsheng Lin's avatar
      net: hns3: fix for miscalculation of rx unused desc · 9f9f0f19
      Yunsheng Lin authored 
      rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.

This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.

Fixes: 76ad4f0e

 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: default avatarYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      9f9f0f19
    • Yunsheng Lin's avatar
      net: hns3: fix the max tx size according to user manual · adfb7b49
      Yunsheng Lin authored 
      Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.

This patch updates the max tx size according to the manual.

Fixes: 8ae10cfb

("net: hns3: support tx-scatter-gather-fraglist feature")
Signed-off-by: default avatarYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      adfb7b49
    • Guangbin Huang's avatar
      net: hns3: add limit ets dwrr bandwidth cannot be 0 · 731797fd
      Guangbin Huang authored 
      If ets dwrr bandwidth of tc is set to 0, the hardware will switch to SP
mode. In this case, this tc may occupy all the tx bandwidth if it has
huge traffic, so it violates the purpose of the user setting.

To fix this problem, limit the ets dwrr bandwidth must greater than 0.

Fixes: cacde272

 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      731797fd
    • Guangbin Huang's avatar
      net: hns3: reset DWRR of unused tc to zero · b63fcaab
      Guangbin Huang authored 
      Currently, DWRR of tc will be initialized to a fixed value when this tc
is enabled, but it is not been reset to 0 when this tc is disabled. It
cause a problem that the DWRR of unused tc is not 0 after using tc tool
to add and delete multi-tc parameters.

For examples, after enabling 4 TCs and restoring to 1 TC by follow
tc commands:

$ tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3 0 1 2 3 queues \
  8@0 8@8 8@16 8@24 hw 1 mode channel
$ tc qdisc del dev eth0 root

Now there is just one TC is enabled for eth0, but the tc info querying by
debugfs is shown as follow:

$ cat /mnt/hns3/0000:7d:00.0/tm/tc_sch_info
enabled tc number: 1
weight_offset: 14
TC    MODE  WEIGHT
0     dwrr    100
1     dwrr    100
2     dwrr    100
3     dwrr    100
4     dwrr      0
5     dwrr      0
6     dwrr      0
7     dwrr      0

This patch fixes it by resetting DWRR of tc to 0 when tc is disabled.

Fixes: 84844054

 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      b63fcaab
    • Jiaran Zhang's avatar
      net: hns3: Add configuration of TM QCN error event · 60484103
      Jiaran Zhang authored 
      Add configuration of interrupt type and fifo interrupt enable of TM QCN
error event if enabled, otherwise this event will not be reported when
there is error.

Fixes: d914971d

 ("net: hns3: remove redundant query in hclge_config_tm_hw_err_int()")
Signed-off-by: default avatarJiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: default avatarGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      60484103
    • Eugene Crosser's avatar
      vrf: Revert "Reset skb conntrack connection..." · 55161e67
      Eugene Crosser authored 
      This reverts commit 09e856d5.

When an interface is enslaved in a VRF, prerouting conntrack hook is
called twice: once in the context of the original input interface, and
once in the context of the VRF interface. If no special precausions are
taken, this leads to creation of two conntrack entries instead of one,
and breaks SNAT.

Commit above was intended to avoid creation of extra conntrack entries
when input interface is enslaved in a VRF. It did so by resetting
conntrack related data associated with the skb when it enters VRF context.

However it breaks netfilter operation. Imagine a use case when conntrack
zone must be assigned based on the original input interface, rather than
VRF interface (that would make original interfaces indistinguishable). One
could create netfilter rules similar to these:

        chain rawprerouting {
                type filter hook prerouting priority raw;
                iif realiface1 ct zone set 1 return
                iif realiface2 ct zone set 2 return
        }

This works before the mentioned commit, but not after: zone assignment
is "forgotten", and any subsequent NAT or filtering that is dependent
on the conntrack zone does not work.

Here is a reproducer script that demonstrates the difference in behaviour.

==========
#!/bin/sh

# This script demonstrates unexpected change of nftables behaviour
# caused by commit 09e856d5 ""vrf: Reset skb conntrack
# connection on VRF rcv"
# https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=09e856d5


#
# Before the commit, it was possible to assign conntrack zone to a
# packet (or mark it for `notracking`) in the prerouting chanin, raw
# priority, based on the `iif` (interface from which the packet
# arrived).
# After the change, # if the interface is enslaved in a VRF, such
# assignment is lost. Instead, assignment based on the `iif` matching
# the VRF master interface is honored. Thus it is impossible to
# distinguish packets based on the original interface.
#
# This script demonstrates this change of behaviour: conntrack zone 1
# or 2 is assigned depending on the match with the original interface
# or the vrf master interface. It can be observed that conntrack entry
# appears in different zone in the kernel versions before and after
# the commit.

IPIN=172.30.30.1
IPOUT=172.30.30.2
PFXL=30

ip li sh vein >/dev/null 2>&1 && ip li del vein
ip li sh tvrf >/dev/null 2>&1 && ip li del tvrf
nft list table testct >/dev/null 2>&1 && nft delete table testct

ip li add vein type veth peer veout
ip li add tvrf type vrf table 9876
ip li set veout master tvrf
ip li set vein up
ip li set veout up
ip li set tvrf up
/sbin/sysctl -w net.ipv4.conf.veout.accept_local=1
/sbin/sysctl -w net.ipv4.conf.veout.rp_filter=0
ip addr add $IPIN/$PFXL dev vein
ip addr add $IPOUT/$PFXL dev veout

nft -f - <<__END__
table testct {
	chain rawpre {
		type filter hook prerouting priority raw;
		iif { veout, tvrf } meta nftrace set 1
		iif veout ct zone set 1 return
		iif tvrf ct zone set 2 return
		notrack
	}
	chain rawout {
		type filter hook output priority raw;
		notrack
	}
}
__END__

uname -rv
conntrack -F
ping -W 1 -c 1 -I vein $IPOUT
conntrack -L

Signed-off-by: default avatarEugene Crosser <crosser@average.org>
Acked-by: default avatarDavid Ahern <dsahern@kernel.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      55161e67
    • Christophe JAILLET's avatar
      net: dsa: Fix an error handling path in 'dsa_switch_parse_ports_of()' · ba69fd91
      Christophe JAILLET authored 
      If we return before the end of the 'for_each_child_of_node()' iterator, the
reference taken on 'port' must be released.

Add the missing 'of_node_put()' calls.

Fixes: 83c0afae

 ("net: dsa: Add new binding implementation")
Signed-off-by: default avatarChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/15d5310d1d55ad51c1af80775865306d92432e03.1634587046.git.christophe.jaillet@wanadoo.fr
Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
      ba69fd91
  3. Oct 19, 2021
    • David S. Miller's avatar
      Merge tag 'linux-can-fixes-for-5.15-20211019' of... · 04ee2752
      David S. Miller authored 
      
Merge tag 'linux-can-fixes-for-5.15-20211019' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2021-10-19

this is a pull request of a single patch for net/master.

The patch is by me and fixes the error handling in case of a FC
timeout in the TX path of the ISOTOP CAN protocol.
====================

Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      04ee2752
    • Zheyu Ma's avatar
      cavium: Fix return values of the probe function · c69b2f46
      Zheyu Ma authored 
      

During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.

Signed-off-by: default avatarZheyu Ma <zheyuma97@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      c69b2f46
    • Zheyu Ma's avatar
      mISDN: Fix return values of the probe function · e2112100
      Zheyu Ma authored 
      

During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.

Signed-off-by: default avatarZheyu Ma <zheyuma97@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      e2112100
    • Marc Kleine-Budde's avatar
      can: isotp: isotp_sendmsg(): fix return error on FC timeout on TX path · d674a8f1
      Marc Kleine-Budde authored 
      When the a large chunk of data send and the receiver does not send a
Flow Control frame back in time, the sendmsg() does not return a error
code, but the number of bytes sent corresponding to the size of the
packet.

If a timeout occurs the isotp_tx_timer_handler() is fired, sets
sk->sk_err and calls the sk->sk_error_report() function. It was
wrongly expected that the error would be propagated to user space in
every case. For isotp_sendmsg() blocking on wait_event_interruptible()
this is not the case.

This patch fixes the problem by checking if sk->sk_err is set and
returning the error to user space.

Fixes: e057dd3f

 ("can: add ISO 15765-2:2016 transport protocol")
Link: https://github.com/hartkopp/can-isotp/issues/42
Link: https://github.com/hartkopp/can-isotp/pull/43
Link: https://lore.kernel.org/all/20210507091839.1366379-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Reported-by: default avatarSottas Guillaume (LMB) <Guillaume.Sottas@liebherr.com>
Tested-by: default avatarOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
      d674a8f1
    • Nathan Chancellor's avatar
      nfp: bpf: silence bitwise vs. logical OR warning · 8a64ef04
      Nathan Chancellor authored 
      

A new warning in clang points out two places in this driver where
boolean expressions are being used with a bitwise OR instead of a
logical one:

drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
        reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg);
                          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                                             ||
drivers/net/ethernet/netronome/nfp/nfp_asm.c:199:20: note: cast one or both operands to int to silence this warning
drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
        reg->src_lmextn = swreg_lmextn(lreg) | swreg_lmextn(rreg);
                          ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                                             ||
drivers/net/ethernet/netronome/nfp/nfp_asm.c:280:20: note: cast one or both operands to int to silence this warning
2 errors generated.

The motivation for the warning is that logical operations short circuit
while bitwise operations do not. In this case, it does not seem like
short circuiting is harmful so implement the suggested fix of changing
to a logical operation to fix the warning.

Link: https://github.com/ClangBuiltLinux/linux/issues/1479
Reported-by: default avatarNick Desaulniers <ndesaulniers@google.com>
Signed-off-by: default avatarNathan Chancellor <nathan@kernel.org>
Reviewed-by: default avatarNick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018193101.2340261-1-nathan@kernel.org
Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
      8a64ef04
  5. Oct 18, 2021
  7. Oct 17, 2021