Add initial device tree nodes for EXYNOS5420 SoC and SMDK5420 board.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Use chipid[27:20] bits to identify the EXYNOS family while setting
up the serial port during the uncompression setup. This uses four
additional bits of chipid to identify the EXYNOS family since this
is required for identifying EXYNOS5420 SoC.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

EXYNOS5420 is new SoC in Samsung's Exynos5 SoC series. Add
initial support for this new SoC.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Instead of having to specify the number for CPUs in EXYNOS5250 in
platsmp.c file, let the number of CPUs be determined by having this
information listed in EXYNOS5250 device tree file.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

In preparation of adding support for EXYNOS5420, which has many
peripherals similar to EXYNOS5250, a new common EXYNOS5 device tree
source file is created out of the exising EXYNOS5250 device tree
source file. Only the common nodes required for basic boot up on
EXYNOS5420 based boards are moved into this new file and the rest
of the common nodes would be moved subsequently.

EXYNOS5440 SoC is quite different from EXYNOS5250 and EXYNOS5420.
Hence it is not possible to reuse "exynos5.dtsi" for EXYNOS5440.

Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add clock lookup information for i2s controllers on exynos5250 SoC.

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Audio subsystem introduced in s5pv210 and exynos platforms
which has a internal clock controller. This patch adds a node
for the same on exynos5250.

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Replace /include/ (dtc) with #include (C pre-processor) for all
Samsung DT files

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Commit 9ee51f01

 (tty: serial/samsung: make register definitions
global) removed the S3C2410_PA_UARTX defines that the newly merged
s3c2416 dt support still expected.

So update mach-s3c2416-dt.c to use the S3C24XX_PA_UART constant until
we have support for the common clock framework the the s3c2416-dt.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The LDO for LCD driver is currently not handled by any of the drivers.
This disables the LDO during booting time. To fix this, the LDO
is forced to enabled always.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added FIMD and display timing node to Origen4210 board.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds pinctrl entries required by FIMD.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

PWM nodes are added to EXYNOS4210 pinctrl DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

By default the exynos RTC is disabled.  Enable it for snow.  There's
also an external RTC on the max77686 PMIC but we haven't yet enabled
that.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

The issues reported in commit 522ccdb6

 ("ARM: dts: Disable the RTC
by default on exynos5") are no longer reproduced on EXYNOS5250 based
Arndale board. Hence re-enabling RTC support for Arndale board.

This is helpful for testing S2R on Arndale board.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Since the pdma works only in secure mode, accessing the same
in hypervisor mode gives an abort. As we are not using pdma
anywhere, removing the same.

Signed-off-by: Giridhar Maruthy <giridhar.m@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Since ssdk5440 and sd5v1 have 8GiB memory, this patch
updates bootargs for them.

Signed-off-by: Subash Patel <subash.rp@samsung.com>
Signed-off-by: Jungseok Lee <jays.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch updates cpu frequency level from 1500 to 800MHZ in steps
of 100MHZ. The corresponding voltage(in uV) is also added.

Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds the required regulator supplies and properties
for wm8994 codec on smdk5250 board.

Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch enables the SPI in EXYNOS5440 SoC. The NOR
Flash can be accessed by enabling the spi interface

Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

EXYNOS5440 includes both OHCI and EHCI usb host controllers.
This patch adds device tree nodes for both of them. And the
EHCI and OHCI controllers on exynos5440 do not need any
explicit phy configuration. So need to assign a different
compatible value for these controllers.

Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added clock entries to G2D node for exynos4x12 DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added clock entries to G2D node.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

G2D node got added twice in exynos4412-smdk4412.dts instead of
getting added to exynos4412-origen.dts. Remove the duplicate entry
and add it to exynos4412-origen.dts.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add pin state information for DP HPD support that requires
pin configuration support using pinctrl interface.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch adds dts support for the sata controller

Signed-off-by: Girish K S <ks.giri@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

This patch is to add vmmc regulator node at MSHC and SDHCI for ODROID-X
board file.

Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

ODROID-X board have a max77686 PMIC on i2c channel 0. The properties of used
LDO and BUCK are defined according the schematic.

Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

RTC is a basic feature of EXYNOS5440. But it was disabled
by issue that comes from EXYNOS5250. (commit id: 522ccdb6

)
That issue only applies to EXYNOS5250 not EXYNOS5440. So,
there is no issue with enabled RTC on EXYNOS5440. This
change was tested on EXYNOS5440.

Signed-off-by: Youngmin Nam <youngmin.nam@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds display timing node for a DP panel to Arndale Board DTS file

Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds clock provider information for DP controller required by CCF.

Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add DT node for DP controller to exynos5250 based Arndale Board

Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

These nodes have separately been added to 4212 and 4412 dtsi
files by commit 30269ddf

 ("ARM: exynos: add missing properties
for combiner IRQs"). The existing node also contained a few
incorrect entries.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add max8997 regulator device node for exynos4210-origen board and list
all the supported regulators.

Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Enables TMU on Origen4210 board.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Adds TMU clock entries to exynos4210.dtsi file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added MFC related clock entries in exynos4.dtsi file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added keypad node entries to SMDK4412 board DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Added keypad node entries to Exynos4412 based Origen board DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Keypad pins/lines are board specific and should be added to respective
board dts files.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>