The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.

Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.

The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.

The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

The Banana Pi series is a well known series of single board computers.
The manufacturer, Sinovoip, is less well known. Moreover, the board
markings do not mention Sinovoip, but only the Banana Pi logo, and
the BPI-M* model name.

Rename the dts file to use the more well known name. Also fix up
some of the model names and labels to match other Banana Pi boards.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This adds the Cirrus Logic EP7209,EP7211 DT templates and support for
EDB7211 Development board.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

- add dts files for Hi3519
- shuffle ARCH_HIGHBANK, ARCH_HISI, ARCH_HIX5HD2 and ARCH_HIP0X
  around to keep the list sorted

Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.

Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.

It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.

The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.

The board is also added to the dts Makefile.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add support for the Broadcom BCM953012 Enterprise Router reference
board, enable the following peripherals:

- UART0 (UART1 is not populated)
- WPS and restart GPIO buttons
- Ethernet switch w/ only two facing ports
- NAND flash
- SPI-NOR flash

Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This is the first Dragonboard based on APQ8060 and PM8058. It
was produced in 2011 in cooperation between Qualcomm and
BSQUARE.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html



So rename this board files so that it reflects actual product in market.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Initial release for rk3229 evb board, and turn the GMAC on.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the initial device  tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them,  so that  the serial console  can  work.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.

Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The BCM958525XMC board is a smaller form factor typically used as
controller boards for switches.  This smaller board has less devices
pinned out, so only a few need be populated in the device tree.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

sam9-l9260 is a low cost board designed by Olimex.

More information is available at:
https://www.olimex.com/Products/ARM/Atmel/SAM9-L9260/



Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add device tree files for the Broadcom BCM23550 SoC and the
Broadcom Sparrow board.

Signed-off-by: Chris Brand <chris.brand@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

commit 27dd9af6

 ("ARM: dts: sunxi: Add a olinuxino-lime2-emmc")
added the new emmc equipped lime2 but forgot its Makefile.

This patch adds an entry to the Makefile.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Create a new device tree file for the Broadcom Northstar Plus HR SVK.
This SVK is a smaller form factor, and thus only has 2 PCI slots and 1
UART.  Also, it has the ability to reboot via GPIO (instead of the
processor reset).

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The Hardkernel's Odroid XU board was first design with big.LITTLE SoC
from Samsung: the Exynos5410. Details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
   enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
   revisions though),
6. eMMC 4.5 and microSD slots.

Comparing this board to Odroid XU3 (more popular), the differences are:
1. Exynos5410 instead of 5422,
2. MIPI DSI LCD connector,
3. Main PMIC: Maxim 77802 instead of S2MPS11,
4. USB3503+LAN9730 instead of integrated LAN9514,
5. eMMC 4.5 instead of eMMC 5.0,

This patch adds initial support for the XU board with working basic
functions, eMMC/SD and USB (including attached ethernet adapter).

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Link: http://www.hardkernel.com/main/products/prdt_info.php?g_code=G137510300620

This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.

Signed-off-by: Joel Stanley <joel@jms.id.au>

A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.

Signed-off-by: Joel Stanley <joel@jms.id.au>

Add initial support for imx6ul pico hobbit board.

For information about this board, please visit:
http://www.wandboard.org/images/hobbit/hobbitboard-imx6ul-reva1.pdf



Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to PHYTEC PHYCORE-LPC3250 board dts
file.

Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

To simplify matching of DTS files of all NXP LPC32xx powered boards by
a file name add 'lpc3250' prefix to Embedded Artists LPC3250 board dts
file.

Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>

Embest MarS Board [1] is a multi-core platform based on Freescale i.MX6
Cortex-A9 Dual Core, running up to 1GHz with 1 GB of RAM, 4GB of eMMC
and with a 4MB SPI flash.

[1] http://www.embest-tech.com/shop/star/marsboard.html



Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Application Notes 399 and 400 shares the same memory map and
features. Both are shipped with Cortex-M7 and have the same  peripheral
as AN385/AN386, but with different location of PSRAM and Ethernet
controller.

Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Application Notes 385 and 386 shares the same memory map and features
except the CPU is used. AN385 is supplied with Cortex-M3 CPU and AN386
is supplied with Cortex-M4.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>

Add Western Digital My Book World Edition device tree based on
Oxford Semiconductor OX810SE SoC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

The MiQi is a rk3288-based devboard from Shenzen based mqmaker, with a
footprint the size of a credit card.

Main available outside connections are 4 usb ports, hdmi, gigabit
ethernet and two expansion headers.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
 - 1 GiB of DRAM
 - 1 Gigabit ethernet
 - 1 USB gadget port
 - 1 USB host port with an on-board hub
 - 2 QSPI NORs connected to the Cadence QSPI core
 - Multiple I2C EEPROMs and one I2C temperature sensor

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>