ia64 has its own optimized percpu accessor - __ia64_per_cpu_var().
Add percpu sparse annotations to it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>

Implement an alternate percpu chunk management based on kernel memeory
for nommu SMP architectures.  Instead of mapping into vmalloc area,
chunks are allocated as a contiguous kernel memory using
alloc_pages().  As such, percpu allocator on nommu will have the
following restrictions.

* It can't fill chunks on-demand page-by-page.  It has to allocate
  each chunk fully upfront.

* It can't support sparse chunk for NUMA configurations.  SMP w/o mmu
  is crazy enough.  Let's hope no one does NUMA w/o mmu.  :-P

* If chunk size isn't power-of-two multiple of PAGE_SIZE, the
  unaligned amount will be wasted on each chunk.  So, archs which use
  this better align chunk size.

For instructions on how to use this, read the comment on top of
mm/percpu-km.c.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Graff Yang <graff.yang@gmail.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>

Separate out and move chunk management (creation/desctruction and
[de]population) code into percpu-vm.c which is included by percpu.c
and compiled together.  The interface for chunk management is defined
as follows.

 * pcpu_populate_chunk		- populate the specified range of a chunk
 * pcpu_depopulate_chunk	- depopulate the specified range of a chunk
 * pcpu_create_chunk		- create a new chunk
 * pcpu_destroy_chunk		- destroy a chunk, always preceded by full depop
 * pcpu_addr_to_page		- translate address to physical address
 * pcpu_verify_alloc_info	- check alloc_info is acceptable during init

Other than wrapping vmalloc_to_page() inside pcpu_addr_to_page() and
dummy pcpu_verify_alloc_info() implementation, this patch only moves
code around.  This separation is to allow alternate chunk management
implementation.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Graff Yang <graff.yang@gmail.com>
Cc: So...

Make the following misc preparations for percpu nommu support.

* Remove refernces to vmalloc in common comments as nommu percpu won't
  use it.

* Rename chunk->vms to chunk->data and make it void *.  Its use is
  determined by chunk management implementation.

* Relocate utility functions and add __maybe_unused to functions which
  might not be used by different chunk management implementations.

This patch doesn't cause any functional change.  This is to allow
alternate chunk management implementation for percpu nommu support.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Graff Yang <graff.yang@gmail.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>

Reorganize alloc/free_pcpu_chunk() such that chunk struct alloc/free
live in pcpu_alloc/free_chunk() and the rest in
pcpu_create/destroy_chunk().  While at it, add missing error handling
for chunk->map allocation failure.

This is to allow alternate chunk management implementation for percpu
nommu support.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Graff Yang <graff.yang@gmail.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>

Factor out pcpu_addr_in_first/reserved_chunk() from
pcpu_chunk_addr_search() and use it to update per_cpu_ptr_to_phys()
such that it handles first chunk differently from the rest.

This patch doesn't cause any functional change and is to prepare for
percpu nommu support.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: David Howells <dhowells@redhat.com>
Cc: Graff Yang <graff.yang@gmail.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: vme: Re-introduce necessary brackets
  Staging: iio: fix up the iio_get_new_idr_val comment
  Staging: add Add Sitecom WL-349 to rtl8192su
  Staging: rt2860: add Belkin F5D8055 Wireless-N USB Dongle device id
  staging: rtl8192su: add Support for Belkin F5D8053 v6
  Staging: dt3155: fix 50Hz configuration
  staging: usbip: Fix deadlock
  Staging: rtl8192su: add USB ID for 0bda:8171
  Staging: hv: name network device ethX rather than sethX
  Staging: hv: Fix up memory leak on HvCleanup
  Staging: hv: Fix a bug affecting IPv6
  staging: iio: ring_sw: Fix incorrect test on successful read of last value, causes infinite loop
  staging: iio: Function iio_get_new_idr_val() return negative value if fails.
  Staging: iio: adc: fix dangling pointers
  Staging: iio: light: fix dangling pointers
  Staging: iio: test for failed allocation
  staging: iio: lis3l02dq - incorrect ws used in container of call.

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  serial: drivers/serial/pmac_zilog.c: add missing unlock
  serial: 8250_pnp - add Fujitsu Wacom device
  tty: Fix regressions in the char driver conversion

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
  USB: sl811-hcd: Fix device disconnect
  USB: ohci-at91: fix power management hanging
  USB: rename usb_buffer_alloc() and usb_buffer_free()
  USB: ti_usb: fix printk format warning
  USB: gadget: s3c-hsotg: Add missing unlock
  USB: fix build on OMAPs if CONFIG_PM_RUNTIME is not set
  USB: oxu210hp: release spinlock on error path
  USB: serial: option: add cinterion device id
  USB: serial: option: ZTEAC8710 Support with Device ID 0xffff
  USB: serial: pl2303: Hybrid reader Uniform HCR331
  USB: option: add ID for ZTE MF 330
  USB: xhci: properly set endpoint context fields for periodic eps.
  USB: xhci: properly set the "Mult" field of the endpoint context.
  USB: OHCI: don't look at the root hub to get the number of ports
  USB: don't choose configs with no interfaces
  USB: cdc-acm: add another device quirk
  USB: fix testing the wrong variable in fs_create_by_name()
  usb: Fix tusb6010 for DMA API
  musb_core: fix musb_init_controller() error cleanup path
  MUSB: fix DaVinci glue layer dependency
  ...

Correct two mishaps which prevented reporting error type (CECC vs UECC)
and extended error description.

Cc: <stable@kernel.org> # 32.x,  33.x
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

CONFIG_INOTIFY_USER defined but CONFIG_ANON_INODES undefined will result
in the following build failure:

    LD      vmlinux
  fs/built-in.o: In function 'sys_inotify_init1':
  (.text.sys_inotify_init1+0x22c): undefined reference to 'anon_inode_getfd'
  fs/built-in.o: In function `sys_inotify_init1':
  (.text.sys_inotify_init1+0x22c): relocation truncated to fit: R_MIPS_26 against 'anon_inode_getfd'
  make[2]: *** [vmlinux] Error 1
  make[1]: *** [sub-make] Error 2
  make: *** [all] Error 2

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'merge' of git://git.secretlab.ca/git/linux-2.6:
  spi: spidev_test gives error upon 1-byte transfer
  omap2_mcspi: small fixes of output data format
  omap2_mcspi: Flush posted writes
  spi: spi_device memory should be released instead of device.
  spi: release device claimed by bus_find_device_by_name
  of: check for IS_ERR()
  serial/mpc52xx_uart: Drop outdated comments
  gpio: potential null dereference

Somehow I managed to remove a set of rather necessary brackets in commit
29848ac9

. Put them back.

Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

improve the comment a bit

Cc: Greg KH <greg@kroah.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add usb id of Sitecom WL-349 to rtl8192su

Signed-off-by: Rodrigo Linfati <rodrigo@linfati.cl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add Belkin F5D8055 Wireless-N USB support to the rt2870
staging driver.

Signed-off-by: Chris Largret <largret@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Please find attached a patch which adds the device ID for the Belkin
F5D8053 v6 to the rtl8192su driver. I've tested this in 2.6.34-rc3
(Ubuntu 9.10 amd64) and the network adapter is working flawlessly.

Signed-off-by: Richard Airlie <richard@backtrace.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

According to the header file, dt3155_io.h, the 50/60 Hz configuration
is controlled by a bit in the I2C CSR2 register (bit 2).  The function
dt3155_init_isr actually reads the I2C CONFIG register into the global
I2C_CSR union variable then modifies the bit.  It then does a write
to the I2C CONFIG register with the global I2C_CONFIG union variable
which is not even set with a value anywhere in the driver.

My guess is 50Hz operation doesn't even work as-is.

Fix this by actually reading and writing the correct register with
the correct value.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

When detaching a port from the client side (usbip --detach 0),
the event thread, on the server side, is going to deadlock.
The "eh" server thread is getting USBIP_EH_RESET event and calls:
  -> stub_device_reset() -> usb_reset_device()
the USB framework is then calling back _in the same "eh" thread_ :
  -> stub_disconnect() -> usbip_stop_eh() -> wait_for_completion()
the "eh" thread is being asleep forever, waiting for its own completion.
This patch checks if "eh" is the current thread, in usbip_stop_eh().

Signed-off-by: Eric Lescouet <eric@lescouet.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This patch makes the HyperV network device use the same naming scheme as
other virtual drivers (Xen, KVM). In an ideal world, userspace tools
would not care what the name is, but some users and applications do
care. Vyatta CLI is one of the tools that does depend on what the name
is.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Don't assign NULL too early

Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix a bug affecting IPv6
Added the multicast flag for proper IPv6 function.

Reported-by: Toshikazu Sakai <toshikas@microsoft.com>
Signed-off-by: Hank Janssen <hjanssen@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This is a bad one. The test means that almost no reads of the last
value ever succeed!  Result is an infinite loop.

Another one for the 'oops' category.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Function iio_get_new_idr_val() return negative value if fails.
So, only error when ret < 0 in iio_device_register_eventset().

Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

We should return test to see if iio_allocate_trigger() fails and return -ENOMEM.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

The word oops comes to mind.  Original patch to merge the two work queues
in here (prior to Greg taking them into staging) changed the top half to
only use one of them and the bottom half to assume it was the other.

Currently causes a NULL pointer dereference if you enable any of the events
on an lis3l02dq. Just goes to show I need a few more regression tests.


Signed-of-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A while ago I provided a patch that fixed device detection after device
removal (USB: sl811-hcd: Fix device disconnect).
Chris Brissette pointed out that the detection/removal counter method
to distinguish insert or remove my fail under certain conditions.
Latest SL811HS datasheet (Document 38-08008 Rev. *D) indicates that
bit 6 (SL11H_INTMASK_RD) of the Interrupt Status Register together with
bit 5 (SL11H_INTMASK_INSRMV) can be used to determine whether a device
has been inserted or removed.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

A hanging has been detected in ohci-at91 while going in suspend to ram. This is
due to asynchronous operations between ohci reset and ohci clocks shutdown.
This patch adds the reading of the control register between the reset of the
ohci and clocks stop. This "flush the writes" idea was taken from ohci-hcd.c
file (ohci_shutdown() function).

Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

For more clearance what the functions actually do,

  usb_buffer_alloc() is renamed to usb_alloc_coherent()
  usb_buffer_free()  is renamed to usb_free_coherent()

They should only be used in code which really needs DMA coherency.

[added compatibility macros so we can convert things easier - gregkh]

Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Pedro Ribeiro <pedrib@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix printk format warning in usbserial/ti_usb:

drivers/usb/serial/ti_usb_3410_5052.c:1738: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

In an error handling case the lock is not unlocked.  The return is
converted to a goto, to share the unlock at the end of the function.

A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/

)

// <smpl>
@r exists@
expression E1;
identifier f;
@@

f (...) { <+...
* spin_lock_irqsave (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

With patch as1329 (USB: convert to the runtime PM framework),
we make USB_SUSPEND depend on PM_RUNTIME instead of CONFIG_PM.

Also, CONFIG_USB_OTG selects CONFIG_USB_SUSPEND.

If PM_RUNTIME is not enabled, and we try to enable USB_OTG,
we will end up with CONFIG_USB_SUSPEND selected. This is
due to a known bug with the select statement.

This makes the build break on various OMAP configs (which
have CONFIG_USB_OTG set by default, but do not yet have
CONFIG_PM_RUNTIME enabled).

Avoid this by changing the logic for CONFIG_USB_OTG from
"select USB_SUSPEND" to "depends on USB_SUSPEND"

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
CC: Michal Marek <mmarek@suse.cz>
CC: Tony Lindgren <tony@atomide.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Smatch complained about this missing spinlock.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

This adds a device id for a Cinterion device.

Reported-by: John Race <John.Race@roscom.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

PATCH TO EXTEND SUPPORT TO AC8710 WITH 0xFFFF Product ID.

Signed-off-by: Mahesh Kuruganti <maheshkuruganti@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

I tried a magnetic stripe reader
(http://www.kimaldi.com/kimaldi_eng/productos/lectores_de_tarjetas/lectores_tarjeta_chip_y_dni/lector_hibrido_uniform_hcr_331

)
and I see that it is interfaced with a PL2303. I wrote a patch to use
your driver which simply adds the product ID for the device and it
seems working fine.


From: Simone Contini <s.contini@oltrelinux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Based on the information provided for by Paweł Drobek, add
a second vendor ID and the correct product ID for ZTE MF 330.

Reported-by: Paweł Drobek <pawel.drobek@gmail.com>
Signed-off: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>