Skip to content
  1. Nov 13, 2013
  3. Nov 11, 2013
  5. Nov 05, 2013
  7. Nov 04, 2013
  9. Nov 01, 2013
  11. Oct 31, 2013
    • Arnaud Ebalard's avatar
      ARM: mvebu: Add Netgear ReadyNAS 104 board · 45e8815f
      Arnaud Ebalard authored 
      

Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:

 - Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
   to be splitted for submission of RTC part first;
 - Front LCD (Winstar 1602G): driver needs to be written
 - Armada NAND controller (to access onboard 128MB of NAND): support
   being pushed by @free-electrons people
 - 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
   driver is available upstream. Not referenced/tested yet.

but the device is usable w/o those.

Signed-off-by: default avatarArnaud Ebalard <arno@natisbad.org>
Acked-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarJason Cooper <jason@lakedaemon.net>
      45e8815f
    • Hiroshi Doyu's avatar
      ARM: tegra: fix Tegra114 IOMMU register address · 4cca9593
      Hiroshi Doyu authored 
      

The IOMMU node's reg property contains completely bogus values! Somehow,
this had no practical effect, despite the fact the IOMMU driver appears
to be writing to those registers. I suppose that since no HW modules is
actually at that address, the writes simply had no effect.

Note that I'm not CCing stable here, even though the problem exists as
far back as v3.9, simply because this patch doesn't fix any observed
issue, and I don't want to run the risk of suddenly writing to some
registers and causing a regression.

Signed-off-by: default avatarHiroshi Doyu <hdoyu@nvidia.com>
[swarren, wrote commit description]
Signed-off-by: default avatarStephen Warren <swarren@nvidia.com>
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
      4cca9593
    • Thomas Petazzoni's avatar
      ARM: kirkwood: add support for OpenBlocks A7 platform · f24b56cb
      Thomas Petazzoni authored 
      

The OpenBlocks A7 board is designed and sold by PlatHome, and based on
a Kirkwood 6283 Marvell SoC. It is quite similar to the OpenBlocks A6
already supported in the kernel, with the following main differences:

 - The A6 uses a RTC on I2C, while the A7 uses the internal SoC RTC.

 - The A6 has one Ethernet port, while the A7 has two Ethernet ports

 - The A6 has only one USB port, while the A7 integrates a USB hub,
   which provides two front-side USB port, and an internal USB port as
   well.

 - The A6 has 512 MB of RAM, while the A7 has 1 GB of RAM.

 - Slightly different GPIOs for some functions.

Signed-off-by: default avatarThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: default avatarAndrew Lunn <andrew@lunn.ch>
Acked-by: default avatarGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: default avatarJason Cooper <jason@lakedaemon.net>
      f24b56cb
  13. Oct 30, 2013
  15. Oct 29, 2013
    • Grant Likely's avatar
      arm/versatile: Fix versatile irq specifications. · 0976c946
      Grant Likely authored 
      

Two of the versatile irq definitions are incorrect, mostly because two
devices have connections to more than one interrupt controller. Fix them
by using the new interrupts-extended property to fan out without using
an awful interrupt-map nexus node.

Signed-off-by: default avatarGrant Likely <grant.likely@linaro.org>
      0976c946
    • Grant Likely's avatar
      of/irq: create interrupts-extended property · 79d97015
      Grant Likely authored 
      

The standard interrupts property in device tree can only handle
interrupts coming from a single interrupt parent. If a device is wired
to multiple interrupt controllers, then it needs to be attached to a
node with an interrupt-map property to demux the interrupt specifiers
which is confusing. It would be a lot easier if there was a form of the
interrupts property that allows for a separate interrupt phandle for
each interrupt specifier.

This patch does exactly that by creating a new interrupts-extended
property which reuses the phandle+arguments pattern used by GPIOs and
other core bindings.

Signed-off-by: default avatarGrant Likely <grant.likely@linaro.org>
Acked-by: default avatarTony Lindgren <tony@atomide.com>
Acked-by: default avatarKumar Gala <galak@codeaurora.org>
[grant.likely: removed versatile platform hunks into separate patch]
Cc: Rob Herring <rob.herring@calxeda.com>
      79d97015
  17. Oct 24, 2013
  19. Oct 23, 2013