There are 3 kinds of OLinuXino Lime2 boards.
One without any on board storage, one with NAND storage and one with
eMMC storage. This patch adds the eMMC variant of boards.

eMMC storage is different from a regular SD card in that it is soldered
on the board and cannot be changed. Additionally, it shares pins with
the NAND module and with the second SPI port.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[Maxime: Removed the change log from the commit log]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable pll3 and pll7 clocks that are needed to drive display clocks.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CHIP has a composite output available muxed with the microphone in the
micro-jack plug.

Enable the composite output in its DTS.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The TCON, tv-encoder and display engine backends and frontends are combined
to create our display pipeline.

Add them to the R8 DTSI. It's supposed to be perfectly compatible with the
A10s and A13, but since we haven't tested it on them yet, it's safer to
just enable it on the R8. Eventually, it should be moved to sun5i.dtsi

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the display and TCON (channel 0 and channel 1) clocks that are going
to be needed to drive the display engine, tcon and TV encoders.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the S/PDIF transmitter present on the Cubietruck.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The DRAM gates control whether the image / display devices on the SoC have
access to the DRAM clock or not.

Enable it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

It turns out that the A13 / R8 also have a tve encoder block, and a gate
for it.

Add it to the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the pll3 and pll7 clocks in the DT that are used to drive the
display-related clocks.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Seems like dram_gate 5 was forgotten when DRAM gating driver was added.

Add it.

Cc: stable@vger.kernel.org
Fixes: 0b4bf5a5

 (ARM: dts: sun7i: Add DRAM gates)
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Seems like dram_gate 5 was forgotten when DRAM gate driver was added.

Enable it.

Cc: stable@vger.kernel.org
Fixes: 82f8582f

 (ARM: dts: sun4i: Add DRAM gates)
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the OTG controller on the Olinuxino A13-micro.

Signed-off-by: Jean-Michel Friedt <jmfriedt@femto-st.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi Plus really is an Orange Pi 2 extended with:
1) A sata <-> usb bridge connected to ehci3
2) An eMMC on mmc2
3) An external gigabit ethernet phy instead of the integrated 100Mbit phy

This commit changes the dts to reflect this by making it include
the Orange Pi 2 dts and then adding the extra bits.

Note that the difference in ethernet phy is not taken into account
because we do not have an ethernet driver for the H3 yet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Fix the following issues with the gpio_keys node:
1) Use of undocumented input-name property
2) Use of a unit-address on the sw2 node
3) Having "PL03" in the pinctrl node which does not exist, this should
   be "PL3"

And add support for the sw2 button on the board.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi 2 is a SBC based on the Allwinner H3 SoC with a uSD slot,
4 USB ports connected via a USB-2 hub, a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via a RTL8189ETV sdio wifi chip, USB OTG, HDMI,
a TRRS headphone jack for stereo out and composite out, a microphone,
an IR receiver, a CSI connector, 2 LEDs, a 3 pin UART header
and a 40-pin GPIO header.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi PC is an SBC based on the Allwinner H3 SoC with a uSD slot,
3 USB ports directly from the SoC, a 10/100M ethernet port using the
SoC's integrated PHY, USB OTG, HDMI, a TRRS headphone jack for stereo out
and composite out, a microphone, an IR receiver, a CSI connector, 2 LEDs,
a 3 pin UART header, and a 40-pin GPIO header.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Fix sun8i-h3-orangepi-plus.dts:
1) Having 2 pio nodes, by merging these into one
2) Having the pio and r_pio nodes before the mmc nodes, while they
   should be sorted by alphabet

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the S/PDIF transmitter that is present on the Itead Ibox.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the S/PDIF transmitter that is present on the A1000.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF transceiver controller block to the A20 dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF transceiver controller block to the A10 dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF clock to the A20 dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF clock to the A10 dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF TX pin to the A20 dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add the SPDIF TX pin to the A10 dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orangepi Plus has a 16GB eMMC, the vcc, the lack of pull-ups and
the use of the hw-reset pin have all been verified with the board
schematic.

With this dts node for mmc2, the eMMC runs at the following ios settings:
clock:          52000000 Hz
vdd:            21 (3.3 ~ 3.4 V)
bus mode:       2 (push-pull)
chip select:    0 (don't care)
power mode:     2 (on)
bus width:      3 (8 bits)
timing spec:    8 (mmc DDR52)
signal voltage: 0 (3.30 V)
driver type:    0 (driver type B)

Note the mmcblk1boot0/boot1 partitions are unused as the BROM will load
the SPL from 8k from the start of the main blockdev, just as with a
regular sdcard in mmc0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Orangepi Plus and Orangepi Plus 2 have a realtek rtl8189etv sdio
wifi chip. This commit adds a device-tree node to power it up, so
that the mmc subsys can scan it, and enables the mmc controller which
is connected to it.

Note that this just makes the wifi controller show up as a sdio device.
In order for it to work a compatible sdio driver is necessary, an out
of tree driver is available here:
https://github.com/jwrdegoede/rtl8189ES_linux/



Binding the driver is not done through device tree, but through sdio
vendor- and device-id, so it can safely be enabled in devicetree
without having a driver upstream yet.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the ir receiver found on the orangepi plus board.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the 2 USB host controllers used on the Orange Pi Plus
and add the necessary regulators.

Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add nodes describing the H3's usbphy and usb host controller nodes.

Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the usb-clks found on the H3.

Signed-off-by: Reinder de Haan <patchesrdh@mveas.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a pinctrl node for mmc2 in 8 bits mode on H3 SoCs.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Dserve DSRV9703C is a 9.7" A10 tablet with a 1024x768 ips LCD,
1G RAM, 4GB flash, a Focaltech FT5406EE8 touchscreen and rtl8188ctv wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Polaroid MID2809PXE4 is a 9" tablet which is clearly marked
Polaroid MID2809PXE4 on the back. It features a 9" 16:9 800x480 LCD,
A23 Soc, 1GB RAM, 8GB NAND, gsl3670 touchscreen and esp8089 wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Address the FIXME comment in sun8i-a23-gt90h-v4.dts now that we've
proper regulator support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

As the dts file name already implies sun8i-a23-gt90h-v4.dts is for
an a23 equipped tablet. I don't know how the "Quad Core" or a33
comaptible got in there, likely a copy and paste error.

Regardless this commit fixes this, note this is almost
purely a cosmetical fix, for all things that matter at the
machine compatible level the a23 and a33 are compatible.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the backlight / pwm found on a23-gt90h-v4 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add nodes for the axp223 pmic and its regulators as found on
a23-gt90h-v4 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The colorfly e708 q1 is a 7" tablet which is clearly marked as colorfly
e708 q1 on the back. It features a 9:16 800x1280 IPS LCD, A31s SoC,
1GB RAM, 8G NAND, ilitek 2139qt004 touchscreen on i2c-1 addr 0x41,
stk8313 accelerometer on i2c-2 addr 0x22 and a rtl8188etv wifi chip.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>