The module 0 clock compatibles were changed between the time the patch was sent
and it was merged. Update the compatibles.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A20-Olinuxino-micro has two SPI bus exposed on its UEXT connectors, enable
them.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A13 has 3 SPI controllers compatible with the one found in the A10. Add
them in the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A10s has 3 SPI controllers compatible with the one found in the A10. Add
them in the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A10 has 4 SPI controllers that are now supported. Add them in the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A20 has 4 SPI controllers compatible with the one found in the A10. Add
them in the DT.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

According to Documentation/devicetree/bindings/regulator/regulator.txt
regulator nodes should not be placed under 'simple-bus'.

Mark Rutland also explains about it at:
http://www.spinics.net/lists/linux-usb/msg101497.html



Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Switch the device tree to the new compatibles introduced in the clock drivers
to have a common pattern accross all Allwinner SoCs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A20 SoC is built around a pair of Cortex-A7 cores,
which have the usual generic timers. Report this in the DT.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

All Allwinner A20 boards we support can only use either EMAC or GMAC,
as they share the same pins. As we have switched all supported to
GMAC, we should alias GMAC (the active controller) as ethernet0,
so u-boot will insert the MAC address for the correct controller.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CubieTruck uses the GMAC with an RGMII phy.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A20 has EMAC and GMAC muxed on the same pins.
Add pin sets with gmac function for MII and RGMII mode to the DTSI.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A31 has 4 SPI controllers. Add them in the DTSI.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The module clocks in the A31 are still compatible with the A10 one. Add the SPI
module clocks and the PLL6 in the device tree to allow their use by the SPI
controllers.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

UART2 is used on CubieTruck to connect to the Bluetooth module.
Add the pin set used in this case.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch will add a basic board support DT for the
LinkSprite pcDuino board.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Pull parisc updates from Helge Deller:
 "The three major changes in this patchset is a implementation for
  flexible userspace memory maps, cache-flushing fixes (again), and a
  long-discussed ABI change to make EWOULDBLOCK the same value as
  EAGAIN.

  parisc has been the only platform where we had EWOULDBLOCK != EAGAIN
  to keep HP-UX compatibility.  Since we will probably never implement
  full HP-UX support, we prefer to drop this compatibility to make it
  easier for us with Linux userspace programs which mostly never checked
  for both values.  We don't expect major fall-outs because of this
  change, and if we face some, we will simply rebuild the necessary
  applications in the debian archives"

* 'parisc-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: add flexible mmap memory layout support
  parisc: Make EWOULDBLOCK be equal to EAGAIN on parisc
  parisc: convert uapi/asm/stat.h to use native types only
  parisc: wire up sched_setattr and sched_getattr
  parisc: fix cache-flushing
  parisc/sti_console: prefer Linux fonts over built-in ROM fonts

HPFS needs to load 4 consecutive 512-byte sectors when accessing the
directory nodes or bitmaps.  We can't switch to 2048-byte block size
because files are allocated in the units of 512-byte sectors.

Previously, the driver would allocate a 2048-byte area using kmalloc,
copy the data from four buffers to this area and eventually copy them
back if they were modified.

In the current implementation of the buffer cache, buffers are allocated
in the pagecache.  That means that 4 consecutive 512-byte buffers are
stored in consecutive areas in the kernel address space.  So, we don't
need to allocate extra memory and copy the content of the buffers there.

This patch optimizes the code to avoid copying the buffers.  It checks
if the four buffers are stored in contiguous memory - if they are not,
it falls back to allocating a 2048-byte area and copying data there.

Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Previously, hpfs scanned all bitmaps each time the user asked for free
space using statfs.  This patch changes it so that hpfs scans the
bitmaps only once, remembes the free space and on next invocation of
statfs it returns the value instantly.

New versions of wine are hammering on the statfs syscall very heavily,
making some games unplayable when they're stored on hpfs, with load
times in minutes.

This should be backported to the stable kernels because it fixes
user-visible problem (excessive level load times in wine).

Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add support for the flexible mmap memory layout (as described in
http://lwn.net/Articles/91829

). This is especially very interesting on
parisc since we currently only support 32bit userspace (even with a
64bit Linux kernel).

Signed-off-by: Helge Deller <deller@gmx.de>

On Linux, only parisc uses a different value for EWOULDBLOCK which
causes a lot of troubles for applications not checking for both values.
Since the hpux compat is long dead, make EWOULDBLOCK behave the same as
all other architectures.

Signed-off-by: Guy Martin <gmsoft@tuxicoman.be>
Signed-off-by: Helge Deller <deller@gmx.de>

The stat.h header file is exported to userspace. Some userspace
applications failed to compile due to missing/unknown types, so we
better convert it to use native types only (like it's done on other
architectures too).

Signed-off-by: Helge Deller <deller@gmx.de>