The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.

Also linewrap like other entries have been lately.

Signed-off-by: Olof Johansson <olof@lixom.net>

for now it is wary basic SoC description with most important IPs needed
to make this device work

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

According to v4l2 dt document, we add:
  a camera host: ISI port.
  a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.

The ov2640 node defines the pinctrls, clocks and refer to isi port.
The ISI node also has a reference to the ov2640 port.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.

We change its name to: pinctrl_pck1_as_isi_mck.

As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.

This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The mck is decided by the board design, move it to mb related
dtsi file.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ISI has 12 data lines, add the missing two data lines.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

As the ISI has 12 data lines, however we only use 8 data lines with
sensor module. So, split the data line into two groups which make
it can be choosed depends on the hardware design.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add ISI peripheral clock in sama5d3.dtsi.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ethernut5 is actually based on an at91sam9xe, use the correct dts include.

Cc: Martin Reimann <martin.reimann@egnite.de>
Cc: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

at91sam9xe is slightly different from at91sam9260, in particular it has a
different SRAM size and location.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.

Also remove leftover TODOs in the sam9g45 file

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable the RTC on the at91rm9200ek.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add a node for the RTC available on at91rm9200.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add node for the RTC available on the at91sam9n12.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The sama4d4 has Special Function Registers that allow to manage DDR, OHCI, EBI
and AIC interrupt redirection.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The sama5d3 has Special Function Registers that allow to manage OHCI, EBI and
the UTMI clock.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

That clock should be called ac97_clk.

Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This D2 led is available for all sama5d3x-ek board. So make it a
heartbeat LED.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

CSR atlas7 uses Network on Chip(NoC) bus architecture, there are dozens
of MARCOs, in each MARCO, there are dozens of hardware modules.

Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

A number of arches (EXYNOS/IMX/TEGRA) are separated out into finer grained
definitions whether it be sub ARCH or SOC definitions. The device tree blobs
should only be built if the specific option is enabled that supports that
device or it might be that there's an expectation that the device is supported
when in actual fact it's not. This ensures only the relevant bits are built.

Also standardised the line break between the arch/soc definitions and the
dtbs to be on separate lines for better consistency as per feedback.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
[olof: Fixed stray \ in one of the IMX rules]
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch enables uart port for the Aquaris5 mobile phone.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

This patch adds the uart ports to the device tree of Mediatek mt6589 SoC.

Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

MARCO will not be supported any more. it has been replaced by CSR
atlas7.

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>

The A388-GP is a board produced by Marvell that holds

- 1 PCIe slot
- 2 mini PCIe slot (one of them is multiplexed with the PCIe slot,
  muxing is selected through the GPIO expander)
- 1 16MB SPI-NOR
- 2 Gigabit Ethernet ports
- 4 SATA ports (2 of them are multiplexed with the mini PCIe slots,
  muxing is selected through the GPIO expander)
- 1 SDIO slot
- 1 USB3 port
- 2 USB2 port
- 2 GPIO/interrupts expander on I2C

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

This SoC belongs to the Armada 38x family. The main difference with
the Armada 385 is that the 388 can handle two more SATA
ports. Currently the consequence is the use of a different compatible
string for the pinctrl node, in order to be able to use the pins
associated to this 2 new SATA ports. The second SATA controller has
also been moved from the armada38x.dtsi as it it specific to the
Armada388 version.

In the same time the Armada385 DB and Armada 385 RD board have been
renamed in the 388 one and now include the armada-388.dtsi file. AS
both of them have 4 SATA ports the SoC used on them were wrongly
described.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

The pintcrl label was missing. Adding it allowed referring it from the
root of the device tree. Also add the uart0 label used by the
bootloader.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

With the Armada 385 GP board more pinctrl functions depending of the
SoC are needed. Add them to the DTSI to avoid duplication.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB
SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage.

[gregory.clement@free-electrons.com: switch the license to the dual
X11/GPL with the agreement of the author]

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Some pinctrl functions can be shared with all DTS out there, since they are
generic, SoC-wide muxing options. Add a number of these to the DTSI to avoid
duplication.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

The compatible set in the armada-38x DTSI is always overridden, and the reg
defined in there is duplicated in the armada-380 and armada-385 DTSIs.

Remove these useless items.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Some nodes in the DTs have a reg property but no unit name in their node name.

This contradicts the way the ePAPR defines the node names. Fix this.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Add sysirq node to mt6592.dtsi and also correct timer interrupt flag.
The old setting works because boot loader already set it.
With a sysirq device node, the timer interrupt can use a correct value.

Signed-off-by: Howard Chen <howard.chen@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

This patch enable UART for MT8127 moose board and MT8135 evalution board.
Adding the dts, these two boards can show log and shell prompts.

Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

According to the gic binding document, "bits[15:8] PPI interrupt cpu
mask.  Each bit corresponds to each of the 8 possible cpus attached to
the GIC.  A bit set to '1' indicated the interrupt is wired to that
CPU." This patch wants to add the PPI cpu mask for completeness.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch adds the pmu node, enabling the PMU unit on Marvell BG2Q and
BG2CD SoCs.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

This patch adds support for Seagate BlackArmor NAS220.

The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has
32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two
USB 2.0 ports, two buttons and three LEDs. There is a serial port available on
the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).

The only functionality still not implemented is the bi-color led on the front
panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and
mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high
results in blue color.

The third led is wired to show the SATA activity on the two drives.

Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

This add dts support for mt8127 and mt8135 SOC UART

Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add sysirq settings for mt6589/mt8135/mt8127
This also correct timer interrupt flag. The old setting works
because boot loader already set polarity for timer interrupt.
Without intpol support, the setting was not changed so gic
can get the irq correctly.

Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add MLB+ clock to R8A7791 device tree.

Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
[Sergei: rebased, renamed, added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>