The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.

Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The imx6q-cm-fx6 iomuxc container node is not required. Remove it.

Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the following dtc warning by removing the unnecessary unit:

Warning (unit_address_vs_reg): Node /matrix-keypad@0 has a unit name,
but no reg property

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This fixes the following dtc warning by removing the unnecessary unit:

Warning (unit_address_vs_reg): Node /onewire@0 has a unit name,
but no reg property

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the missing reg properties for the regulator nodes
in order to fix the dtc warnings.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the missing reg properties for the MXS GPIO banks
in order to fix the dtc warnings.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add the DT property to all boards that have the hardware workaround
for erratum ERR006687 present. This allows the CPUidle driver to use
the deep idle states, even if the FEC is active.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This node describes the DI1 port of IPU, fix the node name to reflect this.
There's currently no user of this node in mainline, so this change should
not break any supported platforms.

Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the LCD8000-43T display and for the backlight
controlled via PWM1.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As of commit 1006ed7e

 ("serial: imx: Use generic uart-has-rtscts
DT property"), the Freescale IMX UART driver recognizes the generic
"uart-has-rtscts" DT property, deprecating the vendor-specific
"fsl,uart-has-rtscts" DT property. Hence replace the latter by the
former in all DTS files.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

As of commit 182cdcb8

 ("serial: mxs-auart: Use generic
uart-has-rtscts DT property"), the Freescale MXS AUART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "fsl,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add 2-pin pinmux settings for AUART2.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add pinmux configuration for SSP2 port in SD mode, both for
the 4-bit and 8-bit case.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This enables support for the CAN controller located in the FPGA.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enable FPGA's IRQ controller. It is in charge of dispatching interrupts
generated by IPs in the FPGA. The SoC is notified that an interrupt
occurred through a GPIO.

Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add input mux for UART2 RX in DTE mode. This allows to use the pad
UART2_TX_DATA_ALT0 as UART2 RX. This particular input select seems
to be missing in current reference manuals (Rev. B), but when looking
at the tables and other UART input select registers (e.g. UART3) it
seems naturally that this input mux register also has a fourth pad
option for UART2_TX_DATA_ALT0. It has also been proven to be required
to use UART2 in DTE mode and the particular pads on the Colibri iMX7
platform.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass "fsl,sai-mclk-direction-output" to the sai2 node, so that the
SAI2_MCLK can be an output.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add SAI alias entries, which makes it possibe for the SAI driver
to retrieve the port instance.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Building with W=1 option leads to several warnings like:

Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property

Fix them by removing the unneeded unit-addresses.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add clocks property for ocotp node.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add clocks property for ocotp node.

Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.

This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3

 ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The device driver was added in v4.5 by commit dca536c4


("watchdog: add support for Sigma Designs SMP86xx/SMP87xx")

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This platform will use the new generic platdev driver.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit fefe0535

 ("clk: tango4: improve clkgen driver") added
support for USB and SDIO clocks.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Define the CPU temperature sensor, and critical trip point.

Commit 799d71da471c ("add temperature sensor support for tango SoC")
added the device driver.

Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

An error in documentation of the NAND Flash Controller (NFC) led to choose
another compatibility string for sama5d2 with an impact on the NAND flash
ready/busy information. It was producing the error message:

atmel_nand 80000000.nand: Time out to wait for interrupt: 0x08000000

and had an impact on performance.

So, switch back to the classical "atmel,sama5d3-nfc" compatibility string for
this SoC which gives the proper ready/busy bit information. The NAND flash
driver will be updated to remove the support for this different
implementation.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Romain Izard <romain.izard.pro@gmail.com>
[nicolas.ferre@atmel.com: change commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.

Signed-off-by: Joel Stanley <joel@jms.id.au>

A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.

Signed-off-by: Joel Stanley <joel@jms.id.au>

Enable pll3 and pll7 clocks that are needed by display clocks.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

There are 3 kinds of OLinuXino Lime2 boards.
One without any on board storage, one with NAND storage and one with
eMMC storage. This patch adds the eMMC variant of boards.

eMMC storage is different from a regular SD card in that it is soldered
on the board and cannot be changed. Additionally, it shares pins with
the NAND module and with the second SPI port.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[Maxime: Removed the change log from the commit log]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

MAX8997 PMIC requires interrupt and fails probing without it.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: d105f0b1

 ("ARM: dts: Add basic dts file for Samsung Trats board")
Cc: <stable@vger.kernel.org>
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The usage of slash character causes failure when creating regulator
debugfs entry.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.kozlowski: Write commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The MFC nodes with the memory regions reserved for memory allocations
are missing in the Exynos5420 Peach Pit and Exynos5800 Peach Pi DTS.

This causes the s5p-mfc driver probe to fail with the following error:

[    4.140647] s5p_mfc_alloc_memdevs:1072: Failed to declare coherent memory for MFC device
[    4.216163] s5p-mfc: probe of 11000000.codec failed with error -12

Add the missing nodes so the driver probes and the {en,de}coder video
nodes are registered correctly:

[    4.096277] s5p-mfc 11000000.codec: decoder registered as /dev/video4
[    4.102282] s5p-mfc 11000000.codec: encoder registered as /dev/video5

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

Add node to support SAMA5D4 hardware random number generator.

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add node to support SAMA5D3 hardware random number generator.

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>