On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.

Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.

The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error

Fixes: 269f399d

 ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add compatible for RK3128's S/PDIF.

Signed-off-by: Alex Bee <knaerzche@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230829171647.187787-4-knaerzche@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

While browsing/grepping in the sound core, I found that
snd_dmaengine_set_config_from_dai_data() did not exist, in favor of
snd_dmaengine_pcm_set_config_from_dai_data(). Fix the typo.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20230922161547.594484-1-miquel.raynal@bootlin.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:

Adding Es83x6 codec entry and HDMI-in capture support in MTL match table.

asoc_simple_probe() is used for both "DT probe" (A) and "platform probe"
(B). It uses "goto err" when error case, but it is not needed for
"platform probe" case (B). Thus it is using "return" directly there.

	static int asoc_simple_probe(...)
	{
 ^		if (...) {
 |			...
(A)			if (ret < 0)
 |				goto err;
 v		} else {
 ^			...
 |			if (ret < 0)
(B)				return -Exxx;
 v		}

		...
 ^		if (ret < 0)
(C)			goto err;
 v		...

	err:
(D)		simple_util_clean_reference(card);

		return ret;
	}

Both case are using (C) part, and it calls (D) when err case.
But (D) will do nothing for (B) case.
Because of these behavior, current code itself is not wrong,
but is confusable, and more, static analyzing tool will warning on
(B) part (should use goto err).

To avoid static analyzing tool warning, this patch uses "goto err"
on (B) part.

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7hy7mlh.wl-kuninori.morimoto.gx@renesas.com


Signed-off-by: Mark Brown <broonie@kernel.org>

It should use "goto" instead of "return"

Fixes: 5ca2ab45

 ("ASoC: simple-card-utils: Add new system-clock-fixed flag")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/202309141205.ITZeDJxV-lkp@intel.com/
Closes: https://lore.kernel.org/all/202309151840.au9Aa2W4-lkp@intel.com/


Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8c76jnz.wl-kuninori.morimoto.gx@renesas.com


Signed-off-by: Mark Brown <broonie@kernel.org>

One more missing SKU in the list.

Closes: https://github.com/thesofproject/linux/issues/4543


Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919092125.1922468-1-yung-chuan.liao@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The rule for the SoundWire tables is that the platforms with more
devices need to be added first. We broke that rule with the Dell SKU
0B34, and caused the second amplifier for SKU 0AF3 to be ignored.

The fix is simple, we need to move the single-amplifier entry after
the two-amplifier one.

Fixes: b62a1a83 ("ASoC: Intel: soc-acpi: add tables for Dell SKU 0B34")
Closes: https://github.com/thesofproject/linux/issues/4559


Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919083606.1920202-1-yung-chuan.liao@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Adding HDMI-In capture via I2S feature support in MTL platform.

Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-3-yung-chuan.liao@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Adding support for ES83x6 codec in MTL match table.

Signed-off-by: Balamurugan C <balamurugan.c@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20230919091136.1922253-2-yung-chuan.liao@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

All the fail paths during probe will free up the ops, on remove we should
only free it if the probe was successful.

Fixes: bc433fd7

 ("ASoC: SOF: Add ops_free")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Link: https://lore.kernel.org/r/20230915124015.19637-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

20s seems unnecessarily large for the DSP init timeout. This coupled with
multiple FW boot attempts causes an excessive delay in the error path when
booting in recovery mode. Reduce it to 0.5s and use the existing
HDA_DSP_INIT_TIMEOUT_US.

Link: https://github.com/thesofproject/linux/issues/4565


Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230915134153.9688-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The microphone and speaker shutters on cs42l43 can be configured to
trigger from the same GPIO, in this case the current code returns an
error as we attempt to request two IRQ handlers for the same IRQ. Fix
this by always requesting the shutter IRQs with the IRQF_SHARED flag.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230915144300.120100-1-ckeepax@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The devm_clk_get() can return -EPROBE_DEFER error,
modify the error code to be -EINVAL is not correct, which
cause the -EPROBE_DEFER error is not correctly handled.

This patch is to fix the return error code.

Fixes: b86ef536

 ("ASoC: fsl: Add Audio Mixer machine driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/1694757731-18308-1-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Because of the potential failure of the devm_kstrdup(), the
dl[i].codecs->name could be NULL.
Therefore, we need to check it and return -ENOMEM in order to transfer
the error.

Fixes: 97030a43

 ("ASoC: Intel: avs: Add HDAudio machine board")
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230915021344.3078-1-nichen@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

In case the widget setup fails we should only decrement the core usage
count if the sof_widget_free_unlocked() has not been called as part of
the error handling.
sof_widget_free_unlocked() calls snd_sof_dsp_core_put() and the additional
core_put will cause imbalance in core usage count.
Use the existing use_count_decremented to handle this issue.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230914124725.17397-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

available_fmt is a pointer.

Fixes: 4fdef47a

 ("ASoC: SOF: ipc4-topology: Add new tokens for input/output pin format count")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230914132504.18463-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

i.MX rpmsg sound cards work on codec slave mode. MCLK will be disabled
by CPU DAI driver in hw_free(). Some codec requires MCLK present at
power up/down sequence. So need to set ignore_pmdown_time to power down
codec immediately before MCLK is turned off.

Take WM8962 as an example, if MCLK is disabled before DAPM power down
playback stream, FIFO error will arise in WM8962 which will have bad
impact on playback next.

Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230913102656.2966757-1-chancel.liu@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:

These patches fix 3 problems with hard reset:
1. Ensure a minimum reset pulse width
2. Deal with ACPI overriding the requested default GPIO state
3. Avoid a race condition when hard-resetting a SoundWire peripheral
   that is already enumerated

wm_adsp_read_ctl() and wm_adsp_write_ctl() must hold the cs_dsp pwr_lock
mutex when calling cs_dsp_coeff_read_ctrl() and cs_dsp_coeff_write_ctrl().

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160250.3700346-1-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Change the logging of each algorithm from info level to debug level.

On the original devices supported by this code there were typically only
one or two algorithms in a firmware and one or two DSPs so this logging
only used a small number of log lines.

However, for the latest devices there could be 30-40 algorithms in a
firmware and 8 DSPs being loaded in parallel, so using 300+ lines of log
for information that isn't particularly important to have logged.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160523.3701189-1-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

In SoundWire mode leave hard RESET asserted when exiting probe,
and wait for an UNATTACHED notification before deasserting RESET.

If the boot state of the reset GPIO was deasserted it is possible
that the SoundWire core had already enumerated the CS42L42 before
cs42l42_sdw_probe() is called. When cs42l42_common_probe() hard
resets the CS42L42 it triggers a race condition:

1) After cs42l42_sdw_probe() returns the thread that called it
   will call cs42l42_sdw_update_status() to report the last
   status recorded by the SoundWire core.

2) The SoundWire bus master will see a PING with the CS42L42
   now reporting as unenumerated and will trigger the core
   SoundWire code to start enumerating CS42L42.

These two threads are racing against each other. If (1)
happens before (2) a stale ATTACHED notification will be
reported to the cs42l42 driver when in fact the status of
cs42l42 is now unattached.

To avoid this race condition:

- Leave RESET asserted on exit from cs42l42_sdw_probe().
  This ensures that an UNATTACHED notification must be
  sent to the cs42l42 driver. If cs42l42 was already
  enumerated it will be seen to drop off the bus, causing
  an UNATTACH notification. If it was never enumerated the
  status is already UNATTACHED and this will be reported
  by thread (1).

- When the UNATTACH notification is received, release RESET.
  This will cause CS42L42 to be enumerated and eventually
  report an ATTACHED notification.

- The ATTACHED notification is now valid.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-4-sbinding@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The ACPI setting for a GPIO default state has higher priority than the
flag passed to devm_gpiod_get_optional() so ACPI can override the
GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting.

Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a
reason to stop passing it to devm_gpiod_get_optional(). So we still pass
it to state our intent, but can deal with it having no effect.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-3-sbinding@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The CS42L42 can accept very short reset pulses of a few microseconds
but there's no reason to force a very short pulse.
Allow a wide range for the usleep_range() so it can be relaxed about
the choice of timing source.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-2-sbinding@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

These error paths should return -EINVAL instead of success.

Fixes: 7f4ec778

 ("ASoC: codecs: Add code for bin parsing compatible with aw88261")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Link: https://lore.kernel.org/r/81476e78-05c2-4656-b754-f314c7ccdb81@moroto.mountain


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Hans de Goede <hdegoede@redhat.com>:

The recent(ish) rt5640 changes to add HDA header jack-detect support
and the related suspend/resume handling fixes have introduced several
issues with IRQ handling on boards not using the HDA header jack-detect
support.

This series fixes these issues, see the individual commit messages
for details.

Do not allow the CS35L56 to be put into its lowest power
"hibernation" mode. This only affects I2C because "hibernation"
is already disabled on SPI and SoundWire.

Recent firmwares need a different wake-up sequence. Until
that sequence has been specified, the chip "hibernation" mode
must be disabled otherwise it can intermittently fail to wake.

THIS WILL NOT APPLY CLEANLY TO 6.5 AND EARLIER:
We will send a separate backport patch to stable.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230912133841.3480466-1-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

If jack-detection is not used; or has already been disabled then
there is no need to call rt5640_cancel_work().

Move the rt5640_cancel_work() inside the "if (rt5640->jack) {}" block,
grouping it together with the disabling of the IRQ which queues the work
in the first place.

This also makes suspend() symetrical with resume() which re-queues the work
in an "if (rt5640->jack) {}" block.

Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-7-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Set "rt5640->irq_requested = true" after a successful request_irq()
in rt5640_enable_hda_jack_detect(), so that rt5640_disable_jack_detect()
properly frees the IRQ.

This fixes the IRQ not being freed on rmmod / driver unbind.

Fixes: 2b9c8d2b

 ("ASoC: rt5640: Add the HDA header support")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-6-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The jack-detect IRQ should be enabled *after* the jack-detect related
configuration registers have been programmed.

Move the enable_irq() call for this to after the register setup.

Fixes: 5fabcc90

 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-5-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

When jack-detect was originally added disabling the IRQ during suspend
was done by the sound/soc/intel/boards/bytcr_rt5640.c driver
calling snd_soc_component_set_jack(NULL) on suspend, which calls
rt5640_disable_jack_detect(), which calls free_irq() which also
disables it.

Commit 5fabcc90 ("ASoC: rt5640: Fix Jack work after system suspend")
added disable_irq() / enable_irq() calls on suspend/resume for machine
drivers which do not call snd_soc_component_set_jack(NULL) on suspend.

The new disable_irq() / enable_irq() are made conditional by
"if (rt5640->irq)" statements, but this is true for the machine drivers
which do call snd_soc_component_set_jack(NULL) on suspend too, causing
a disable_irq() call there on the already free-ed IRQ.

Change the "if (rt5640->irq)" condition to "if (rt5640->jack)" to fix this,
rt5640->jack is only set if the jack-detect IRQ handler is still active
when rt5640_suspend() runs.

And adjust rt5640_enable_hda_jack_detect()'s request_irq() error handling
to set rt5640->jack to NULL to match (note that the old setting of irq to
-ENOXIO still resulted in disable_irq(-ENOXIO) calls on suspend).

Fixes: 5fabcc90

 ("ASoC: rt5640: Fix Jack work after system suspend")
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-4-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Following prints are observed while testing audio on Jetson AGX Orin which
has onboard RT5640 audio codec:

  BUG: sleeping function called from invalid context at kernel/workqueue.c:3027
  in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/0
  preempt_count: 10001, expected: 0
  RCU nest depth: 0, expected: 0
  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:159 __handle_irq_event_percpu+0x1e0/0x270
  ---[ end trace ad1c64905aac14a6 ]-

The IRQ handler rt5640_irq() runs in interrupt context and can sleep
during cancel_delayed_work_sync().

The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
avoiding the sleep in atomic context.

Fixes: 051dade3

 ("ASoC: rt5640: Fix the wrong state of JD1 and JD2")
Reported-by: Sameer Pujar <spujar@nvidia.com>
Closes: https://lore.kernel.org/r/1688015537-31682-4-git-send-email-spujar@nvidia.com


Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-3-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 70a6404f ("ASoC: rt5640: Fix sleep in atomic context")
not only switched from request_irq() to request_threaded_irq(),
to fix the sleep in atomic context issue, but it also added
devm management of the IRQ by actually switching to
devm_request_threaded_irq() (without any explanation in the commit
message for this change).

This is wrong since the IRQ was already explicitly managed by
the driver. On unbind the ASoC core will call rt5640_set_jack(NULL)
which in turn will call rt5640_disable_jack_detect() which
frees the IRQ already. So now we have a double free.

Besides the unexplained switch to devm being wrong, the actual fix
for the sleep in atomic context issue also is not the best solution.

The only thing which rt5640_irq() does is cancel + (re-)queue
the jack_work delayed_work. This can be done in a single non sleeping
call by replacing queue_delayed_work() with mod_delayed_work(),
which does not sleep. Using mod_delayed_work() is a much better fix
then adding a thread which does nothing other then queuing a work-item.

This patch is a straight revert of the troublesome changes, the switch
to mod_delayed_work() is done in a separate follow-up patch.

Fixes: 70a6404f

 ("ASoC: rt5640: Fix sleep in atomic context")
Cc: Sameer Pujar <spujar@nvidia.com>
Cc: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230912113245.320159-2-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Like the Lenovo 82TL and 82V2, the Lenovo 82QF (Yoga 7 14ARB7) and 82UG
(Legion S7 16ARHA7) both need a quirk entry for the internal microphone to
function. Commit c008323f ("ASoC: amd: yc: Fix a non-functional mic on
Lenovo 82SJ") restricted the quirk that previously matched "82" to "82V2",
breaking microphone functionality on these devices. Fix this by adding
specific quirks for these models, as was done for the Lenovo 82TL.

Fixes: c008323f ("ASoC: amd: yc: Fix a non-functional mic on Lenovo 82SJ")
Closes: https://github.com/tomsom/yoga-linux/issues/51
Link: https://bugzilla.kernel.org/show_bug.cgi?id=208555#c780


Cc: stable@vger.kernel.org
Signed-off-by: August Wikerfors <git@augustwikerfors.se>
Link: https://lore.kernel.org/r/20230911213409.6106-1-git@augustwikerfors.se


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Sameer Pujar <spujar@nvidia.com>:

This small series fixes redundant PLLA updates that happen for
each DAI link in the audio path. This helps to resolve DMIC clock
issue seen on Jetson TX2 platform.

The rpmsg pcm device is a device which should support
double buffering.

Found this issue with pipewire. When there is no
SNDRV_PCM_INFO_BATCH flag in driver, the pipewire will
set headroom to be zero, and because rpmsg pcm device
don't support residue report, when the latency setting
is small, the "delay" always larger than "target" in
alsa-pcm.c, that reading next period data is not
scheduled on time.

With SNDRV_PCM_INFO_BATCH flag in driver, the pipewire
will select a smaller period size for device, then
the task of reading next period data will be scheduled
on time.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1694414287-13291-1-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Walt Holman <waltholman09@gmail.com>
Link: https://lore.kernel.org/r/20230910185433.13677-1-waltholman09@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Commit ac950278

 ("ASoC: add N cpus to M codecs dai link support")
added an additional local params in __soc_pcm_hw_params, for the CPU
side of the DAI. The snd_pcm_hw_params struct is pretty large (604
bytes) and keeping two local copies of it can make the stack frame
really large.

It is worth noting the variables are in separate code blocks so for
some optimisation levels in the compiler these will get automatically
combined keeping the stack frame reasonable. But better to manually
combine them to cover all cases.

Add a single local variable for __soc_pcm_hw_params and use in both
loops to shrink the stack frame.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230908085920.2906359-1-ckeepax@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 422f10ad ("ASoC: wm8960: Add support for the power supplies")
added regulator support to the wm8960 driver, but neglected to update
error handling in the probe function. This results in warning backtraces
if the probe function fails.

Fixes: 422f10ad

 ("ASoC: wm8960: Add support for the power supplies")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Link: https://lore.kernel.org/r/20230909120237.2646275-1-linux@roeck-us.net


Signed-off-by: Mark Brown <broonie@kernel.org>

for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.

This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci

Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20230907095521.14053-11-Julia.Lawall@inria.fr


Signed-off-by: Mark Brown <broonie@kernel.org>