* marvell/dt: (41 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Now that we have I2C support in DT, describe the LM63 in
the DT file for the iConnect.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>

Now that the GPIO controllers have been converted over to DT,
described the gpio-keys in DT.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>

Move description of GPIO keys on both the DNS320 and DNS325 into DT.

Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

A lot of device setup is shared between DNS-320 and DNS-325, move the
definitions into a common include.

Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Replace code in board-dnskw with the equivalent devicetree bindings.

Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Now that we have I2C support in DT, describe the LM75 in
the DT file for the DNS325.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>

Convert boards using DT, but the old way of configuring SATA to now
use properties in there DT file.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>

Use the device tree for the SPI driver and partition layout.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Add support for Buffalo Linkstation LS-XHL and LS-CHLv2 using the device
tree where possible.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

This patch supplies the necessary DTS and supporting files to boot up
a Seagate GoFlex Net with 3.5.0-rc3.

Signed-off-by: Joshua Coombs <josh.coombs@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

The two different variants of QNAP TS devices, varying by SoC, put the
GPIO keys on different GPIO lines. Hence we need two different DT
board descriptions, which share the same board-ts219.c file.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>

Add support for instantiating this driver from device tree, and add
the necassary DT information to the kirkwood.dtsi file.

This is based on previous work by Michael Walle and Jason Cooper.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Josh Coombs <josh.coombs@gmail.com>

Add device tree support to the Orion watchdog timer, and enable its
use in the kirkwood devices using device tree.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>

The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Conflicts:
	arch/arm/mach-kirkwood/common.c

Populate the devices with auxdata to set the device names which are used by
clkdev to lookup the clocks.

Signed-off-by: Michael Walle <micheal@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
---
v2: Add interrupts properties, although not used.

Both IRQ and GPIO controllers can now be represented in DT.  The IRQ
controllers are setup first, and then the GPIO controllers. Interrupts
for GPIO lines are placed directly after the main interrupts in the
interrupt space.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Josh Coombs <josh.coombs@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>

Merge in branch already pulled. Fulfils dependancies needed by
this patchset.

spi: Updates for 3.6

Since Grant is even more specacularly busy than usual for the time being
I've been collecting SPI patches for him for this release - probably
things will revert back to Grant before the next release.  There's
nothing too exciting here, mostly it's simple driver specific stuff:

- Add spi: to the modaliases of SPI devices to provide namespacing.
- A driver for AD-FMCOMMS1-EBZ.
- DT binding for Orion.
- Fixes and cleanups for i.MX, PL0022, OMAP and bitbang drivers.

There may be a few more fixes I've missed, people keep sending me new
things.

It has been decided to use marvell, not mrvl, in the compatibility
property. Search & replace.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

The clk patches added code to get and enable clocks in the
respective driver probe functions.  If the probe function failed
for some reason after enabling the clock, the clock was not
disabled again in many cases.

Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lumm <andrew@lunn.ch>

The last argument of orion_ge00_init() is actually the error
interrupt, so we should be using the correct value here.

Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Commit 98d9986c

 (ARM: Kirkwood: Replace clock gating) and the fix 5fb2ce
(ARM: Kirkwood: clk_register_gate_fn: add fn assignment) introduced a custom
variant of clock gating which allows to define a function to be called
before gating the clock off.

This is used to disable the SATA and PCIe PHYs if the respective clocks
are unused after initialization.

However, of these two drivers, the SATA driver may be compiled as a module.
The driver re-enables the clocks at module init but the PHYs stay disabled.

Since the custom clock gating disabled the PHYs when gating the clock off,
it should also re-enable them when enabling the clock gate.  This is done by
adding a second function that may be used to enable the PHYs.

Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>

Marvell engineers tell us:

	It seems that many units use the RUNIT clock.
	SPI, UART, NAND, TWSI, ...
	So it's not possible to clock gate it.

Currently the SPI, NAND and TWSI driver will clk_prepaure_enable()
this clk, but since we have no idea what ... is, and turning this clk
off results in a hard lock, unconditionally enable runit.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>

This was formerly used to store the tclk value. This is now discovered
using the clk API, rather than pass it as platform data.

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We are currently using an inferior or equal operator for comparing
the transfer frequency with the clock frequency table. Because of
this, we always end up selecting 20Mhz as a frequency, due to the
inequality transfer hz <= 20 Mhz being always true. Fix this by
reversing the inequality, which is how the comparison should be done.

Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This warning recently appeared with omap2plus_defconfig:

WARNING: drivers/spi/built-in.o(.devinit.text+0x3c4): Section mismatch in reference from the function omap2_mcspi_probe() to the function .init.text:omap2_mcspi_master_setup()
The function __devinit omap2_mcspi_probe() references
a function __init omap2_mcspi_master_setup().
If omap2_mcspi_master_setup is only used by omap2_mcspi_probe then
annotate omap2_mcspi_master_setup with a matching annotation.

The fix is obviously to mark the omap2_mcspi_master_setup function as
__devinit, rather than __init.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The SYSTEM_SUSPEND_DISK system state is never used, so drop it.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge emailed kgdb dmesg fixups patches from Anton Vorontsov:
 "The dmesg command appears to be broken after the printk rework.  The
  old logic in the kdb code makes no sense in terms of current
  printk/logging storage format, and KDB simply hangs forever upon
  entering 'dmesg' command.

  The first patch revives the command by switching to kmsg_dumper
  iterator.  As a side-effect, the code is now much more simpler.

  A few changes were needed in the printk.c: we needed unlocked variant
  of the kmsg_dumper iterator, but these can surely wait for 3.6.

  It's probably too late even for the first patch to go to 3.5, but I'll
  try to convince otherwise.  :-) Here we go:

   - The current code is broken for sure, and has no hope to work at
     all.  It is a regression
   - The new code works for me, and probably works for everyone else;
   - If it compiles (and I urge everyone to compile-test it on your
     setup), it hardly can make things worse."

* Merge emailed patches from Anton Vorontsov: (4 commits)
  kdb: Switch to nolock variants of kmsg_dump functions
  printk: Implement some unlocked kmsg_dump functions
  printk: Remove kdb_syslog_data
  kdb: Revive dmesg command

The locked variants are prone to deadlocks (suppose we got to the
debugger w/ the logbuf lock held), so let's switch to nolock variants.

Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If used from KDB, the locked variants are prone to deadlocks (suppose we
got to the debugger w/ the logbuf lock held).

So, we have to implement a few routines that grab no logbuf lock.

Yet we don't need these functions in modules, so we don't export them.

Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The function is no longer needed, so remove it.

Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The kgdb dmesg command is broken after the printk rework.  The old logic
in kdb code makes no sense in terms of current printk/logging storage
format, and KDB simply hangs forever.

This patch revives the command by switching to kmsg_dumper iterator.

The code is now much more simpler and shorter.

Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>