OSC_SWITCH_STATUS is a volatile register indicating the current state
of the clock switch logic.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-15-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

According to the datasheet the SRC MCLK must be as near as possible to
(125 * sample rate). This means it should be ~6MHz for rates up to 48k
and ~12MHz for rates above that. As per datasheet table 4-21.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-14-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

After enabling the HP or ADC by writing the corresponding PDN=0,
it takes around 20 milliseconds for it to power up and the midrail
supply to be stable. Add this wait into a DAPM widget callback.

If HP and ADC are both powering up in a DAPM sequence, there's no
need to do the wait twice. The widget will perform one wait in the
POST_PMU if there was a PRE_PMU for one or both.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-13-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

It isn't possible to switch MCLK between 12MHz and 24MHz rate groups
on-the-fly - this can only be done when cs42l42 is powered-down.

All "normal" SCLK rates use an MCLK in the 12MHz group, so change the
configs for SCLK > 12.288 MHz to use the PLL to generate an MCLK in
the 12MHz group.

As this means MCLK_DIV is always 0 it can be removed from the pll
configuration setup.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-12-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The driver currently only supports configuring for sample rates <= 96k
and it isn't possible to setup a configuration that will support all
sample rates up to 192k.

For sample rates up to 96k MCLK is in the 12MHz group.
However, although 192k only requires an I2S clock in the 12MHz group,
the cs42l42 audio path is not natively 192k so the audio must be
resampled. But for 192k the SRC requires a 24MHz MCLK.

It is not possible to switch MCLK between 12MHz and 24MHz groups
on-the-fly. The 12MHz group supports all sample rates up to 96k.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-11-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The driver can run without an interrupt so if devm_request_threaded_irq()
failed, the probe() just carried on. But if this was EPROBE_DEFER the
driver would continue without an interrupt instead of deferring to wait
for the interrupt to become available.

Fixes: 2c394ca7 ("ASoC: Add support for CS42L42 codec")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-6-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Volatile registers don't need a default value.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca7 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211015133619.4698-5-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Some registers had wrong default values in cs42l42_reg_defaults[].

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2c394ca7 ("ASoC: Add support for CS42L42 codec")
Link: https://lore.kernel.org/r/20211015133619.4698-4-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

An I2S frame always has two slots (left and right) even when sending
mono. The right channel (channel 2) of ASP TX will always have the
same bit width as the left channel and will always be on the high
phase of LRCLK.

The previous implementation always passed the field masks for both
channels to snd_soc_component_update_bits() but for mono the written value
only contained the settings for channel 1. The result was that for mono
channel 2 was set to 8-bit (which is an invalid configuration) with both
channels on the low phase of LRCLK.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 585e7079 ("ASoC: cs42l42: Add Capture Support")
Link: https://lore.kernel.org/r/20211015133619.4698-3-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

When capture and playback substreams are both running at the same time,
cs42l42_pcm_hw_params() would be called for each direction. The first
call will configure the PLL. The second call must not write the PLL
configuration registers again if the first substream is already running,
as this could destabilize the PLL.

The DAI is marked symmetric sample bits and sample rate, so the two
directions will always have the same SCLK (I2S always has 2 channel slots
so the DAI does not need to require symmetric channels to guarantee the
same SCLK). However, since cs42l42_pll_config() is checking for an active
stream it may as well test that the requested SCLK is the same as the
currently active configuration.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211015133619.4698-2-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

There is a noise issue for 8kHz sample rate on slave mode.
Compared with master mode, the difference is the DACDIV
setting, after correcting the DACDIV, the noise is gone.

There is no noise issue for 48kHz sample rate, because
the default value of DACDIV is correct for 48kHz.

So wm8960_configure_clocking() should be functional for
ADC and DAC function even if it is slave mode.

In order to be compatible for old use case, just add
condition for checking that sysclk is zero with
slave mode.

Fixes: 0e50b51a ("ASoC: wm8960: Let wm8960 driver configure its bit clock and frame clock")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/1634102224-3922-1-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Ensure the default 0dB playback path is always used.

The code that set FULL_SCALE_VOL based on LOAD_DET_RCSTAT was
spurious, and resulted in a -6dB attenuation being accidentally
inserted into the playback path.

Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211011144903.28915-1-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

'component' is allocated in snd_soc_register_component(), but component->list
is not initalized, this may cause snd_soc_del_component_unlocked() deref null
ptr in the error handing case.

KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:__list_del_entry_valid+0x81/0xf0
Call Trace:
 snd_soc_del_component_unlocked+0x69/0x1b0 [snd_soc_core]
 snd_soc_add_component.cold+0x54/0x6c [snd_soc_core]
 snd_soc_register_component+0x70/0x90 [snd_soc_core]
 devm_snd_soc_register_component+0x5e/0xd0 [snd_soc_core]
 tas2552_probe+0x265/0x320 [snd_soc_tas2552]
 ? tas2552_component_probe+0x1e0/0x1e0 [snd_soc_tas2552]
 i2c_device_probe+0xa31/0xbe0

Fix by adding INIT_LIST_HEAD() to snd_soc_component_initialize().

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211009065840.3196239-1-yangyingliang@huawei.com


Signed-off-by: Mark Brown <broonie@kernel.org>

This patch fixes compilation error in wcd98x codec driver.

Fixes: 04544222 ("ASoC: codecs: wcd938x: add audio routing and Kconfig")

Signed-off-by: Venkata Prasad Potturu <potturu@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1633614675-27122-1-git-send-email-srivasam@codeaurora.org


Signed-off-by: Mark Brown <broonie@kernel.org>

The put callback of a kcontrol is supposed to return 1 when the value
is changed, and this will be notified to user-space.  However, some
DAPM kcontrols always return 0 (except for errors), hence the
user-space misses the update of a control value.

This patch corrects the behavior by properly returning 1 when the
value gets updated.

Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211006141712.2439-1-tiwai@suse.de


Signed-off-by: Mark Brown <broonie@kernel.org>

dev_err_probe() avoids printing into log when the deferred probe is invoked.
This is possible when clock provider is pending to appear.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211006150428.16434-4-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

First of all, replace indexed API by plain one since we have index 0.
Second, switch to optional variant and drop duplicated code.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211006150428.16434-3-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211006150428.16434-2-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Access to platform data via dev_get_platdata() getter to make code cleaner.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.com>
Link: https://lore.kernel.org/r/20211006150428.16434-1-andriy.shevchenko@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

This patch is to fix audio 3.5mm jack detection failure
on wcd938x codec based target.

Fixes: bcee7ed0 (ASoC: codecs: wcd938x: add Multi Button Headset Control support)

Signed-off-by: Venkata Prasad Potturu <potturu@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/1633614619-27026-1-git-send-email-srivasam@codeaurora.org


Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 1d25684e ("ASoC: nau8824: Fix open coded prefix handling")
replaced the nau8824_dapm_enable_pin() helper with direct calls to
snd_soc_dapm_enable_pin(), but the helper was using
snd_soc_dapm_force_enable_pin() and not forcing the MICBIAS + SAR
supplies on breaks headphone vs headset and button-press detection.

Replace the snd_soc_dapm_enable_pin() calls with
snd_soc_dapm_force_enable_pin() to fix this.

Cc: stable@vger.kernel.org
Fixes: 1d25684e ("ASoC: nau8824: Fix open coded prefix handling")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210929201512.460360-1-hdegoede@redhat.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding SPI IDs for parts that
only have a compatible listed.

Fixes: 96c8395e ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: patches@opensource.cirrus.com
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210924194844.45974-1-broonie@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding SPI IDs for parts that
only have a compatible listed.

Fixes: 96c8395e ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210924194956.46079-1-broonie@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

With pause and resume test for ARC, there is occasionally
channel swap issue. The reason is that currently driver set
the DPATH out of reset first, then start the DMA, the first
data got from FIFO may not be the Left channel.

Moving DPATH out of reset operation after the dma enablement
to fix this issue.

Fixes: 28564486 ("ASoC: fsl_xcvr: Add XCVR ASoC CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1631265510-27384-1-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Commit 25d27c4f ("ASoC: pcm512x: Add support for more data formats")
breaks the TSE-850 device, which is using a pcm5142 in I2S and
CBM_CFS mode (maybe not relevant). Without this fix, the result
is:

pcm512x 0-004c: Failed to set data format: -16

And after that, no sound.

This fix is not 100% correct. The datasheet of at least the pcm5142
states that four bits (0xcc) in the I2S_1 register are "RSV"
("Reserved. Do not access.") and no hint is given as to what the
initial values are supposed to be. So, specifying defaults for
these bits is wrong. But perhaps better than a broken driver?

Fixes: 25d27c4f ("ASoC: pcm512x: Add support for more data formats")
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Kirill Marinushkin <kmarinushkin@birdec.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: alsa-devel@alsa-project.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/2d221984-7a2e-7006-0f8a-ffb5f64ee885@axentia.se


Signed-off-by: Mark Brown <broonie@kernel.org>

Do not print error message from snd_sof_trace_notify_for_error() when
possible sleeping trace work is woken up to flush the remaining debug
information.

This action by itself is not an error, it is just an action we take when
an error occurs to make sure that all information have been fed to the
userspace (if we have trace in use).

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210917085108.25532-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

S24_LE params fixup is only required for DPTX.
Remove fixup ops assignment for HDMITX.

Fixes: 40d605df ("ASoC: mediatek: mt8195: add machine driver with mt6359, rt1019 and rt5682")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210917082805.30898-1-trevor.wu@mediatek.com


Signed-off-by: Mark Brown <broonie@kernel.org>

In case the firmware is missing we will have the following in the kernel
log:

1 | Direct firmware load for intel/sof/sof-tgl-h.ri failed with error -2
2 | error: request firmware intel/sof/sof-tgl-h.ri failed err: -2
3 | you may need to download the firmware from https://github.com/thesofproject/sof-bin/
4 | error: failed to load DSP firmware -2
5 | error: sof_probe_work failed err: -2

The first line is the standard, request_firmware() warning.
The second and third line is printed in snd_sof_load_firmware_raw()
Note that the first and second line is mostly identical.

With this patch the log will be changed to:
1 | Direct firmware load for intel/sof/sof-tgl-h.ri failed with error -2
2 | error: sof firmware file is missing, you might need to
3 |        download it from https://github.com/thesofproject/sof-bin/


4 | error: failed to load DSP firmware -2
5 | error: sof_probe_work failed err: -2

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20210916085342.29993-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Invoke release_firmware() when the firmware fails to boot in
sof_probe_continue().

The request_firmware() framework must be informed of failures in
sof_probe_continue() otherwise its internal "batching"
feature (different from caching) cached the firmware image
forever. Attempts to correct the file in /lib/firmware/ were then
silently and confusingly ignored until the next reboot. Unloading the
drivers did not help because from their disconnected perspective the
firmware had failed so there was nothing to release.

Also leverage the new snd_sof_fw_unload() function to simplify the
snd_sof_device_remove() function.

Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210916085008.28929-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

i.MX8 only uses SOF_FW_BLK_TYPE_IRAM (1) and SOF_FW_BLK_TYPE_SRAM (3)
bars, everything else is left as 0 in sdev->bar[] array.

If a broken or purposefully crafted firmware image is loaded with other
types of FW_BLK_TYPE then a kernel crash can be triggered.

Make sure that only IRAM/SRAM type is converted to bar index.

Fixes: afb93d71 ("ASoC: SOF: imx: Add i.MX8M HW support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210915122116.18317-6-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

i.MX8 only uses SOF_FW_BLK_TYPE_IRAM (1) and SOF_FW_BLK_TYPE_SRAM (3)
bars, everything else is left as 0 in sdev->bar[] array.

If a broken or purposefully crafted firmware image is loaded with other
types of FW_BLK_TYPE then a kernel crash can be triggered.

Make sure that only IRAM/SRAM type is converted to bar index.

Fixes: 202acc56 ("ASoC: SOF: imx: Add i.MX8 HW support")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210915122116.18317-5-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Fix @buf arg given to hex_dump_to_buffer() and stack address used
in dump error output.

Fixes: e657c18a ('ASoC: SOF: Add xtensa support')
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20210915063230.29711-1-peter.ujfalusi@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series "ASoC: fsl: register platform component before registering cpu dai" from Shengjiu Wang <shengjiu.wang@nxp.com>:

There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()

snd_soc_register_card()
  -> snd_soc_bind_card()
    -> snd_soc_add_pcm_runtime()
      -> adding cpu dai
      -> adding codec dai
      -> adding platform component.

So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.

As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.

This patch set is to fix this issue for SAI, ESAI, MICFIL, SPDIF,
XCVR drivers.

Shengjiu Wang (5):
  ASoC: fsl_sai: register platform component before registering cpu dai
  ASoC: fsl_esai: register platform component before registering cpu dai
  ASoC: fsl_micfil: register platform component before registering cpu
    dai
  ASoC: fsl_spdif: register platform component before registering cpu
    dai
  ASoC: fsl_xcvr: register platform component before registering cpu dai

 sound/soc/fsl/fsl_esai.c   | 16 ++++++++++------
 sound/soc/fsl/fsl_micfil.c | 15 ++++++++++-----
 sound/soc/fsl/fsl_sai.c    | 14 +++++++++-----
 sound/soc/fsl/fsl_spdif.c  | 14 +++++++++-----
 sound/soc/fsl/fsl_xcvr.c   | 15 ++++++++++-----
 5 files changed, 48 insertions(+), 26 deletions(-)

--
2.17.1

When memory allocation for afe->reg_back_up fails, reg_back_up can't
be used.
Keep the suspend/resume flow but skip register backup when
afe->reg_back_up is NULL, in case illegal memory access happens.

Fixes: 283b6124 ("ASoC: mediatek: implement mediatek common structure")
Signed-off-by: Trevor Wu <trevor.wu@mediatek.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20210910092613.30188-1-trevor.wu@mediatek.com


Signed-off-by: Mark Brown <broonie@kernel.org>

There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()

snd_soc_register_card()
  -> snd_soc_bind_card()
    -> snd_soc_add_pcm_runtime()
      -> adding cpu dai
      -> adding codec dai
      -> adding platform component.

So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.

As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.

Fixes: 28564486 ("ASoC: fsl_xcvr: Add XCVR ASoC CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-6-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()

snd_soc_register_card()
  -> snd_soc_bind_card()
    -> snd_soc_add_pcm_runtime()
      -> adding cpu dai
      -> adding codec dai
      -> adding platform component.

So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.

As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.

Fixes: a2388a49 ("ASoC: fsl: Add S/PDIF CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-5-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()

snd_soc_register_card()
  -> snd_soc_bind_card()
    -> snd_soc_add_pcm_runtime()
      -> adding cpu dai
      -> adding codec dai
      -> adding platform component.

So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.

As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.

Fixes: 47a70e6f ("ASoC: Add MICFIL SoC Digital Audio Interface driver.")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-4-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()

snd_soc_register_card()
  -> snd_soc_bind_card()
    -> snd_soc_add_pcm_runtime()
      -> adding cpu dai
      -> adding codec dai
      -> adding platform component.

So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.

As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.

Fixes: 43d24e76 ("ASoC: fsl_esai: Add ESAI CPU DAI driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-3-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

There is no defer probe when adding platform component to
snd_soc_pcm_runtime(rtd), the code is in snd_soc_add_pcm_runtime()

snd_soc_register_card()
  -> snd_soc_bind_card()
    -> snd_soc_add_pcm_runtime()
      -> adding cpu dai
      -> adding codec dai
      -> adding platform component.

So if the platform component is not ready at that time, then the
sound card still registered successfully, but platform component
is empty, the sound card can't be used.

As there is defer probe checking for cpu dai component, then register
platform component before cpu dai to avoid such issue.

Fixes: 43550821 ("ASoC: Add SAI SoC Digital Audio Interface driver")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1630665006-31437-2-git-send-email-shengjiu.wang@nxp.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The 00d38fd8d2524 ("MAINTAINERS: update references to stm32 audio bindings")
commit update the bindings reference, by
removing bindings/sound/st,stm32-adfsdm.txt, to set the
new reference to bindings/iio/adc/st,stm32-*.yaml.

This leads to "get_maintainer finds" the match for the
Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml,
but also to the IIO bindings
Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml

And The commit fixes only a part of the problem:
Documentation/devicetree/bindings/sound/st,stm32-*.txt file have been
also moved to yaml.

Update references to include all stm32 audio bindings file and
exclude the st,stm32-adc.yaml bindings file.

cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fixes: 0d38fd8d ("MAINTAINERS: update references to stm32 audio bindings")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20210909145449.24388-1-arnaud.pouliquen@foss.st.com


Signed-off-by: Mark Brown <broonie@kernel.org>