Skip to content
  1. Aug 28, 2014
  3. Aug 27, 2014
  5. Aug 24, 2014
  7. Aug 22, 2014
  9. Aug 20, 2014
  11. Aug 19, 2014
  13. Aug 18, 2014
    • Imre Deak's avatar
      drm/i915: don't try to retrain a DP link on an inactive CRTC · 1a125d8a
      Imre Deak authored 
      Atm we may retrain the DP link even if the CRTC is inactive through
HPD work->intel_dp_check_link_status(). This in turn can lock up the PHY
(at least on BYT), since the DP port is disabled.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=81948


Signed-off-by: default avatarImre Deak <imre.deak@intel.com>
Reviewed-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      1a125d8a
    • Imre Deak's avatar
      drm/i915: make sure VDD is turned off during system suspend · 07f9cd0b
      Imre Deak authored 
      

Atm we may leave eDP VDD enabled during system suspend after the CRTCs
are disabled through an HPD->DPCD read event. So disable VDD during
suspend at a point when no HPDs can occur.

Note that runtime suspend doesn't have the same problem, since there the
RPM ref held by VDD provides already the needed serialization.

v2:
- add note to commit message about the runtime suspend path (Ville)
- use edp_panel_vdd_off_sync(), so we can keep the WARN in
  edp_panel_vdd_off() (Ville)
v3:
- rebased on -fixes (for_each_intel_encoder()->list_for_each_entry())
  (Imre)

Signed-off-by: default avatarImre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
[Jani: fix sparse warning reported by Fengguang Wu]
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      07f9cd0b
    • Imre Deak's avatar
      drm/i915: cancel hotplug and dig_port work during suspend and unload · 1d0d343a
      Imre Deak authored 
      

Make sure these work handlers don't run after we system suspend or
unload the driver. Note that we don't cancel the handlers during runtime
suspend. That could lead to a lockup, since we take a runtime PM ref
from the handlers themselves. Fortunaltely canceling there is not needed
since the RPM ref itself provides for the needed serialization.

v2:
- fix the order of canceling dig_port_work wrt. hotplug_work (Ville)
- zero out {long,short}_hpd_port_mask and hpd_event_bits for speed
  (Ville)

Signed-off-by: default avatarImre Deak <imre.deak@intel.com>
Reviewed-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      1d0d343a
    • Imre Deak's avatar
      drm/i915: fix HPD IRQ reenable work cancelation · 6323751d
      Imre Deak authored 
      

Atm, the HPD IRQ reenable timer can get rearmed right after it's
canceled. Also to access the HPD IRQ mask registers we need to wake up
the HW.

Solve both issues by converting the reenable timer to a delayed work and
grabbing a runtime PM reference in the work. By this we can also forgo
canceling the timer during runtime suspend, since the only important
thing there is that the HW is awake when we write the registers and
that's ensured by the RPM ref. So do the cancelation only during driver
unload time; this is also a requirement for an upcoming patch where we
want to cancel all HPD related works only during system suspend and
driver unload time, but not during runtime suspend.

Note that there is still a race between the HPD IRQ reenable work and
drm_irq_uninstall() during driver unload, where the work can reenable
the HPD IRQs disabled by drm_irq_uninstall(). This isn't a problem since
the HPD IRQs will still be effectively masked by the first level
interrupt mask.

v2-3:
- unchanged
v4:
- use proper API for changing the expiration time for an already pending
  delayed work (Jani)

Signed-off-by: default avatarImre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v2)
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      6323751d
    • Imre Deak's avatar
      drm/i915: take display port power domain in DP HPD handler · 1c767b33
      Imre Deak authored 
      

Ville noticed that we can call ibx_digital_port_connected() which accesses
the HW without holding any power well/runtime pm reference. Fix this by
holding a display port power domain reference around the whole hpd_pulse
handler.

Signed-off-by: default avatarImre Deak <imre.deak@intel.com>
Reviewed-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: default avatarDave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org (3.16+)
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      1c767b33
    • Dave Airlie's avatar
      Merge branch 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux · c39502c5
      Dave Airlie authored 
      radeon fixes for 3.17, kind of all over the place (dpm, GPUVM, etc.)
* 'drm-fixes-3.17' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: Remove duplicate include from Makefile
  drm/radeon/dpm: select the appropriate vce power state for KV/KB/ML
  drm/radeon: Add ability to get and change dpm state when radeon PX card is turned off
  drm/radeon: Add missing lines to ci_set_thermal_temperature_range
  drm/radeon: Always flush VM again on < CIK
  drm/radeon: add a check for allocation failure (v2)
  drm/radeon: use pfp for all vm_flush related updates
  drm/radeon: add bapm module parameter
      c39502c5
    • Ville Syrjälä's avatar
      drm/i915: Don't try to enable cursor from setplane when crtc is disabled · 1add143c
      Ville Syrjälä authored 
      

Make sure the cursor gets fully clipped when enabling it on a disabled
crtc via setplane. This will prevent the lower level code from
attempting to enable the cursor in hardware.

Cc: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: default avatarChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      1add143c
    • Ville Syrjälä's avatar
      drm/i915: Skip load detect when intel_crtc->new_enable==true · a459249c
      Ville Syrjälä authored 
      

During suspend we turn off the crtcs, but leave the staged config in
place so that we can restore the display(s) to their previous state on
resume.

During resume when we attempt to apply the force pipe A quirk we use the
load detect mechanism. That doesn't check whether there was an already
staged configuration for the crtc since that's not even possible during
normal runtime load detection. But during resume it is possible, and if
we just blindly go and overwrite the staged crtc configuration for the
load detection we can no longer restore the display to the correct
state.

Even worse, we don't even clear all the staged connector->encoder->crtc
links so we may end up using a cloned setup for the load detection, and
after we're done we just clear the links related to the VGA output
leaving the links for the other outputs in place. This will eventually
result in calling intel_set_mode() with mode==NULL but with valid
connector->encoder->crtc links which will result in dereferencing the
NULL mode since the code thinks it will have to a modeset.

To avoid these problems don't use any crtc with new_enabled==true for
load detection.

Signed-off-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org (for 3.16)
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      a459249c
    • Ville Syrjälä's avatar
      drm/i915: Fix locking for intel_enable_pipe_a() · 208bf9fd
      Ville Syrjälä authored 
      

intel_enable_pipe_a() gets called with all the modeset locks already
held (by drm_modeset_lock_all()), so trying to grab the same
locks using another drm_modeset_acquire_ctx is going to fail miserably.

Move most of the drm_modeset_acquire_ctx handling (init/drop/fini)
out from intel_{get,release}_load_detect_pipe() into the callers
(intel_{crt,tv}_detect()). Only the actual locking and backoff
handling is left in intel_get_load_detect_pipe(). And in
intel_enable_pipe_a() we just share the mode_config.acquire_ctx from
drm_modeset_lock_all() which is already holding all the relevant locks.

It's perfectly legal to lock the same ww_mutex multiple times using the
same ww_acquire_ctx. drm_modeset_lock() will convert the returned
-EALREADY into 0, so the caller doesn't need to do antyhing special.

Fixes a hang on resume on my 830.

Signed-off-by: default avatarVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: default avatarDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarJani Nikula <jani.nikula@intel.com>
      208bf9fd
  15. Aug 17, 2014
  17. Aug 16, 2014