This is BCM53573 WiSoC based access point with an extra BCM43217 chipset
used for 2.4 GHz.

Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This is BCM47094 (AKA BCM4709C0) based router with rear-facing ports
board design.

Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This is BCM47094 (AKA BCM4709C0) based router with ports-on-the-front
board design.

Signed-off-by: Dan Haab <dhaab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This info can be used by operating system to setup LED behavior.

Reported-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM43438 (bluetooth) as a slave device of uart0 (pl011/ttyAMA0).
This allows to automatically insert the bcm43438 to the bluetooth
subsystem instead of relying on userspace helpers (hciattach).

Overwrite chosen/stdout-path to use 8250 aux uart as console.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>

Contrary to other RPi devices, RPi3 uses uart0 to communicate with
the BCM43438 bluetooth controller. uart1 is then used for the console.
Today, the console configuration is inherited from the bcm283x dtsi
(bootargs) which is not the correct one for the RPi3. This leads to
routing issue and confuses the Bluetooth controller with unexpected
data.

This patch introduces chosen/stdout path to configure console to uart0
on bcm283x family and overwrite it to uart1 in the RPi3 dts.

Create serial0/1 aliases referring to uart0 and uart1 paths.
Remove unneeded earlyprintk.

Fixes: 4188ea2a

 ("ARM: bcm283x: Define UART pinmuxing on board level")
Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>

This is connected up to the backlight on 911360_entphn, which we'll
need for a panel driver. For now, leave the node disabled in the
shared dtsi.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This doesn't yet enable it on any particular platform, as we still
need a panel driver for bcm911360_entphn.

Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes msi-parent to refer to all
MSI controller dts nodes.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

"1" should be replaced by "l". This is a typo.
The patch is to fix it.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

AT91SAM9G45 has an AC97 controller, but it is not described in the dts
file.
This patch adds AC97 node in device tree.

Signed-off-by: Dmitry Rezvanov <dmitry.rezvanov@yandex.ru>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add pinctrl groups of ethenet phy mode, such as "ether_rgmii", "ether_rmii",
and "ether_mii".

Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

All registers are located within 0x400 size from the base address.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Add UniPhier AIDET (ARM Interrupt Detector) nodes to support
active low interrupts.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

Since the discussion is not settled yet for the EMAC, and that the release
in getting really close, let's revert the changes for now, and we'll
reintroduce them later.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This reverts commit ddb56254

. The EMAC
bindings have not stabilized yet, so we can't commit to keeping them
stable.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This patch solves the following error:
arch/arm/boot/dts/rk3228-evb.dtb: ERROR (phandle_references): Reference to non-existent node or label "phy0"

Fixess db40f15b

 ("ARM: dts: rk3228-evb: Enable the integrated PHY for gmac")
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the as3645a flash controller to the DT source.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>

CEC support was added for Exynos5 in 4.13, but for the Odroids we need to set
'needs-hpd' as well since CEC is disabled when there is no HDMI hotplug signal,
just as for the exynos4 Odroid-U3.

This is due to the level-shifter that is disabled when there is no HPD, thus
blocking the CEC signal as well. Same close-but-no-cigar board design as the
Odroid-U3.

Tested with my Odroid XU4.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Rockchip's rv1108-evb board has one usb otg controller and one usb
host controller, each usb controller connect with one usb-phy port
through UTMI+ interface. This patch enables them to support usb on
rv1108-evb board.

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch adds usb otg/host controllers and phys nodes for RV1108 SoCs.

Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The window of the Aspeed AST2400 SMC Controllers to map chips on the
AHB Bus has a 256MB size. The full window range is

    [ 0x20000000 - 0x2FFFFFFF ] for the FMC controller
    [ 0x30000000 - 0x3FFFFFFF ] for the SPI controller

This change requires CONFIG_VMSPLIT_2G to be set.

Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>

The cpu is powered by regulator vdd_core on RV1108 evalution
board. Add it to the cpu dt node.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add cpu opp table for rv1108 to support frequency
from 408MHZ to 1008MHZ.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds the operating points to the Ux500 device tree and
deletes the old special-purpose cpufreq node, as we can now
use the generic DT cpufreq driver.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add VPU/VDEC/VOP/IEP iommu nodes

Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Earlyconsole is used for early kernel debugging that's why this option
shouldn't be enabled by default.
Earlyconsole is partially copying the part of the bootlog after
"bootconsole [uart0] disabled".

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all Zynq device trees inline
with each other.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This will simplify dt overlay structure for the whole PL.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.

Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Describe adv7511 on i2c bus.

Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

This adds a new node for the LEGO MINDSTORMS EV3 LCD display.

Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add dt node of bosch accelerometer bma250e on rv1108 evb.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

RK805 is used as the voltage regulator on rv1108 evaluation
board. Add device tree node for it.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

To prevent unintended modifications to the kernel text (malicious or
otherwise) while running the EFI stub, describe the kernel image as
two separate sections: a .text section with read-execute permissions,
covering .text, .rodata, .piggytext and the GOT sections (which the
stub does not care about anyway), and a .data section with read-write
permissions, covering .data and .bss.

This relies on the firmware to actually take the section permission
flags into account, but this is something that is currently being
implemented in EDK2, which means we will likely start seeing it in
the wild between one and two years from now.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170818194947.19347-12-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Replace the various open coded constants in the EFI PE/COFF header with
definitions from pe.h, or expressions based on local symbols.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170818194947.19347-11-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The kernel's EFI PE/COFF header contains a dummy .reloc section, and
an explanatory comment that claims that this is required for the EFI
application loader to accept the Image as a relocatable image (i.e.,
one that can be loaded at any offset and fixed up in place)

This was inherited from the x86 implementation, which has elaborate host
tooling to mangle the PE/COFF header post-link time, and which populates
the .reloc section with a single dummy base relocation. On ARM, no such
tooling exists, and the .reloc section remains empty, and is never even
exposed via the BaseRelocationTable directory entry, which is where the
PE/COFF loader looks for it.

The PE/COFF spec is unclear about relocatable images that do not require
any fixups, but the EDK2 implementation, which is the de facto reference
for PE/COFF in the UEFI space, clearly does not care, and explicitly
mentions (in a comment) that relocatable images with no base relocations
are perfectly fine, as long as they don't have the RELOCS_STRIPPED
attribute set (which is not the case for our PE/COFF image)

So simply remove the .reloc section altogether.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170818194947.19347-10-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

Bring the PE/COFF header in line with the PE/COFF spec, by setting
NumberOfSymbols to 0, and removing the section alignment flags.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170818194947.19347-9-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>

The BPI-M3 is an Allwinner A83T based SBC in the Bananapi/Bpi family.
It is roughly the same form factor as the BPI-M1+, with roughly the
same peripherals and connectors:

  - 2GB LPDDR3 DRAM
  - 8GB eMMC
  - Micro-SD card slot
  - HDMI output
  - Headset (stereo + mic) jack
  - Onboard mic
  - Gigabit Ethernet with RTL8211E transceiver
  - Ampak AP6212 WiFi + BT
  - USB OTG connector
  - USB-to-SATA bridge connected through a USB 2.0 hub
  - Consumer IR receiver
  - MIPI DSI LCD panel connector
  - Camera interface (parallel and MIPI CSI) connector
  - 3 LEDs (Red, Green, Blue), of which 2 are controllable (GB)
  - Raspberry Pi 2 compatible GPIO header

Signed-off-by: Chen-Yu Tsai <wens@csie.org>

RV1108 EVB uses pwm0 modulate the backlight, add dt
node to enable it.

Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>