The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.

Tested on OMAP4 SDP board and Pandaboard ES2.

Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Following commit ff5c9059

 and therefore other omap platforms using
the gpio-omap driver correct the #interrupt-cells property on am33xx
too. The omap gpio binding documentaion also states that
the #interrupt-cells property should be 2.

Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

ARM Performance Monitor Units are available on the am33xx,
add the support in the dtsi.

Tested with perf and oprofile on a regular beaglebone.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEP COM MOdule has a GPIO LED connected to OMAP
pins. Configure this pin as output GPIO.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

The IGEPv2 has a number of GPIO LED connected to OMAP
pins. Configure these pins as output GPIO.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

IGEP boards have a number of LED connected to OMAP or TWL GPIO
lines. The actual wiring is different on each board so each board
DT has need to configure the mux correctly.

Even though it works with the current DT, the kernel complains with:

[2.305023] leds-gpio leds.18: pins are not configured from the driver

Add an empty pinmux_leds_pins pinctrl child node so boards can
override with the correct mux configuration and not depend on
default values for the GPIO LEDs to work.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This adds device tree with necessary support to boot with functional
video (on both emulator and real N900 device).

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Turn on SDHCI for i.MX support so machines can boot with local rootfs
on SD. Tested on a Wandboard Quad.

Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>

When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4

.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.

The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.

Also introduced is a minor clean up of a checkpatch error in old code.

Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Balaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

On the TC2 testchip, when all CPUs in a cluster enter standbywfi
and commit a power down request, the power controller will wait
for standbywfil2 coming from L2 cache controller to shut the
cluster down.
By the time all CPUs in a cluster commit a power down request
and enter wfi, the power controller cannot backtrack, or put it
another way, a CPU must not be allowed to complete execution
independently of the power controller, the only way for it to
resume properly must be upon wake-up IRQ pending and subsequent
reset triggered from the power controller.

Current MCPM back-end for TC2 disables the GIC CPU IF only when
power down is committed through the tc2_pm_suspend() method, that
makes sense since a suspended CPU is still online and can receive
interrupts whereas a hotplugged CPU, since it is offline,
migrated all IRQs and shutdown the per-CPU peripherals, hence
their PPIs.

The flaw with this reasoning is the following. If all CPUs in
a clusters are entering a power down state either through CPU
idle or CPU hotplug, when the last man successfully completes
the MCPM power down sequence (and executes wfi), power controller
waits for L2 wfi signal to quiesce the cluster and shut it down.
If, when all CPUs are sitting in wfi, an online CPU hotplugs back
in one of the CPUs in the cluster being shutdown, that CPU
receives an IPI that causes wfi to complete (since tc2_pm_down()
method does not disable the GIC CPU IF in that case - CPU being
hotplugged out, not idle) and the power controller will never see
the stanbywfil2 signal coming from L2 that is required for
shutdown to happen and the system deadlocks.

Further to this issue, kexec hotplugs secondary CPUs out during
kernel reload/restart.
Because kexec may (deliberately) trash the old kernel text, it is
not OK for CPUs to follow the MCPM soft reboot path, since
instructions after the WFI may have been replaced by kexec.

If tc2_pm_down() does not disable the GIC cpu interface, there is a
race between CPU powerdown in the old kernel and the IPI from the
new kernel that triggers secondary boot, particularly if the
powerdown is slow (due to L2 cache cleaning for example).  If the
new kernel wins the race, the affected CPU(s) will not really be
reset and may execute garbage after the WFI.

The only solution to this problem consists in disabling the GIC
CPU IF on a CPU committed to power down regardless of the power
down entry method (CPU hotplug or CPU idle). This way, CPU wake-up
is under power controller control, which prevents unexpected wfi
exit caused by a pending IRQ.

This patch moves the GIC CPU IF disable call in the TC2 MCPM
implementation from the tc2_pm_suspend() method to the
tc2_pm_down() method to fix the mentioned race condition(s).

Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec)
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.

Signed-off-by: Renwei Wu <Renwei.Wu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.

Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

ad65782f

 (context_tracking: Optimize main APIs off case
with static key) converted context tracking main APIs to inline
function and left ARM asm callers behind.

This can be easily fixed by making ARM calling the post static
keys context tracking function. We just need to replicate the
static key checks there. We'll remove these later when ARM will
support the context tracking static keys.

Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Anil Kumar <anilk4.v@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@linaro.org>

This fixes a compile error where CONFIG_PCI is disabled:

  LD      init/built-in.o
arch/arm/mach-integrator/built-in.o: In function `ap_map_io':
integrator_cp.c:(.init.text+0x570): undefined reference to `pci_v3_early_init'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2

Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

cpu_reset is already #defined in <asm/proc-fns.h> as processor.reset,
so it expands here and causes problems.

Cc: <stable@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

This property is no longer required by the GPIO binding. Remove it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

e5c9b4cd

 ("sh_eth: get R8A7740 support
out of #ifdef") exchanged sh-eth driver name to r8a7740-gether, but,
eva_pinctrl_map[] didn't follow it. Fixes it.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Patch 638591cd

 enabled building the AES assembler code in Thumb2 mode.
However, this code used arithmetic involving PC rather than adr{l}
instructions to generate PC-relative references to the lookup tables,
and this needs to take into account the different PC offset when
running in Thumb mode.

Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

This prevents the linker erroring with:

arm-linux-ld: error: arch/arm/lib/xor-neon.o uses VFP instructions, whereas arch/arm/lib/built-in.o does not
arm-linux-ld: failed to merge target specific data of file arch/arm/lib/xor-neon.o

This is due to the non-neon files being marked as containing FPA data/
instructions (even though they do not) being mixed with files which
contain VFP, which is an incompatible floating point format.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 377747c4

 ("ARM: entry: allow ARM-private syscalls to be
restarted") reworked the low-level syscall dispatcher to allow
restarting of ARM-private syscalls. Unfortunately, this relocated the
label used to dispatch a private syscall from the trace path, so that
the invocation would be bypassed altogether!

This causes applications to fail under strace as soon as they rely on
a private syscall (e.g. set_tls):

  set_tls(0xb6fad4c0, 0xb6fadb98, 0xb6fb1050, 0xb6fad4c0, 0xb6fb1050)
      = -1 ENOSYS (Function not implemented)

This patch fixes the label so that we correctly dispatch private
syscalls from the trace path.

Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Currently on the Lager board NFS timeouts/delays are seen when booting.  That
turned out to happen because the SoC's ETH_LINK signal turns on and off after
each packet.  It is connected to Micrel KSZ8041 PHY's LED0 signal. Ether LEDs
on the Lager board are named LINK and ACTIVE which corresponds to non-default
01 setting of the PHY control register 1 bits 14-15. The 'sh_eth' driver resets
the PHY when opening the network device, so we have to set the mentioned bits
back to 01 from the default 00 value which causes bouncing of ETH_LINK.  That
can be achieved using the PHY platform fixup mechanism if we also modify the
driver to use it..

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

There appears to be an error in the second address of the second XOR
engine in the Kirkwood SoC device tree, which is specified as 0xd0b00
but should be 0x60b00.

For confirmation of address see table 581 page 658 of:

http://www.marvell.com/embedded-processors/kirkwood/assets/FS_88F6180_9x_6281_OpenSource.pdf



Also see definition of XOR1_HIGH_PHYS_BASE in
arch/arm/mach-kirkwood/include/mach/kirkwood.h

Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This flag is a NOOP since 2.6.36 and can be removed.

This is an update for 3.11 of a patch already sent for 3.10

Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Replace pinctrl_usart2_rts and pinctrl_usart2_cts istead of pinctrl_uart2_*.

Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>