This describe the new bindings for the added IRQ support in the
pinctrl-microchip-sgpio driver.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201209142753.683208-3-lars.povlsen@microchip.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds 'interrupt-controller' features for the signals available on
the Microchip SGPIO controller, however only for controller versions
on the Sparx5 platform (or later).

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201209142753.683208-2-lars.povlsen@microchip.com


[Select GPIOLIB_IRQCHIP in Kconfig]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add initial pinctrl driver to support pin configuration for
LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8250.

This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:

TLMM GPIO[146 - 159] --> LPASS LPI GPIO [0 - 13]

This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201202163443.26499-3-srinivas.kandagatla@linaro.org


[Add some dependencies]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add device tree binding Documentation details for Qualcomm SM8250
LPASS(Low Power Audio Sub System) LPI(Low Power Island) pinctrl driver.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201202163443.26499-2-srinivas.kandagatla@linaro.org


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

PM55 pmic support gpio controller so add compatible and comment for gpio
holes

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201126092151.1082697-2-vkoul@kernel.org


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for the PMX55 GPIO support to the Qualcomm PMIC GPIO
binding.

Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201126092151.1082697-1-vkoul@kernel.org


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix the following sparse warnings:

drivers/pinctrl/pinctrl-microchip-sgpio.c:63:31: warning: symbol 'properties_luton' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:68:31: warning: symbol 'properties_ocelot' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:73:31: warning: symbol 'properties_sparx5' was not declared. Should it be static?

Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1606218173-3722-1-git-send-email-zou_wei@huawei.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

If CONFIG_HAS_IOMEM is not set, devm_platform_ioremap_resource() will
be not built in drivers/base/platform.c and then there exists a build
error about undefined reference to "devm_platform_ioremap_resource"
in pinctrl-at91-pio4.c under COMPILE_TEST and CONFIG_PINCTRL_AT91PIO4,
make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix it.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1606209423-4742-1-git-send-email-yangtiezhu@loongson.cn


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch is used to fix low level output voltage issue.
A pin is changed from input pull-up to output high.
The Dout value of the pin is default as 0.
If we change the direction of the pin before the dout value of the pin,
It maybe produce a low level output voltage between "input pull-up" and
"output high".

Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20201120093058.7248-2-zhiyong.tao@mediatek.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

if of_find_device_by_node() succeed, pinctrl_falcon_probe() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.

Fixes: e316cb2b

 ("OF: pinctrl: MIPS: lantiq: adds support for FALCON SoC")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20201119011219.2248232-1-yukuai3@huawei.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

s500_padinfo[] is never modified and should be made 'const' to allow
the compiler to optimize code generation, i.e. put it in the text
section instead of the data section.

Before:
   text    data     bss     dec     hex filename
  12503    5088       0   17591    44b7 drivers/pinctrl/actions/pinctrl-s500.o

After:
   text    data     bss     dec     hex filename
  14435    3156       0   17591    44b7 drivers/pinctrl/actions/pinctrl-s500.o

Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Link: https://lore.kernel.org/r/24505deb08d050eb4ce38f186f4037d7541ea217.1605722628.git.cristian.ciocaltea@gmail.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinctrl-microchip-sgpio driver needs OF support, so add that to
Kconfig.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20201125122014.11237-1-lars.povlsen@microchip.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
(SGPIO) device used in various SoC's.

The driver is added as a pinctrl driver, albeit only having just GPIO
support currently. The hardware supports other functions that will be
added following.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201113145151.68900-3-lars.povlsen@microchip.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds DT bindings for the Microsemi/Microchip SGPIO controller,
bindings microchip,sparx5-sgpio, mscc,ocelot-sgpio and
mscc,luton-sgpio.

Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201113145151.68900-2-lars.povlsen@microchip.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'samsung-pinctrl-5.11' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel

Samsung pinctrl drivers changes for v5.11

Only a cleanup of unneeded breaks.

Merge tag 'renesas-pinctrl-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: renesas: Updates for v5.11 (take two)

  - Add QSPI pin groups on R-Car E3, H3, M3-W/W+, and M3-N,
  - A small fix for a Clang warning.

Some products, like sama7g5, do not have a full last bank of PIO lines.
In this case for example, sama7g5 only has 8 lines for the PE bank.
PA0-31, PB0-31, PC0-31, PD0-31, PE0-7, in total 136 lines.
To cope with this situation, added a data attribute that is product dependent,
to specify the number of lines of the last bank.
In case this number is different from the macro ATMEL_PIO_NPINS_PER_BANK,
adjust the total number of lines accordingly.
This will avoid advertising 160 lines instead of the actual 136, as this
product supports, and to avoid reading/writing to invalid register addresses.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201113132429.420940-1-eugen.hristev@microchip.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'intel-pinctrl-v5.11-1' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into devel

intel-pinctrl for v5.11-1

 * Add Intel Alder Lake-S pin controller support
 * Add Intel Elkhart Lake pin controller support
 * Add Intel Lakefield driver pin controller support
 * Miscellaneous fixes for Intel Lynxpoint driver

The following is an automated git shortlog grouped by driver:

intel:
 -  Add Intel Alder Lake-S pin controller support
 -  Add Intel Elkhart Lake pin controller support
 -  Add blank line before endif in Kconfig
 -  Add Intel Lakefield pin controller support

lynxpoint:
 -  Enable pin configuration setting for GPIO chip
 -  Use defined constant for disabled bias explicitly
 -  Unify initcall location in the code

It is found on many allwinner soc that there is a low probability that
the interrupt status cannot be read in sunxi_pinctrl_irq_handler. This
will cause the interrupt status of a gpio bank to always be active on
gic, preventing gic from responding to other spi interrupts correctly.

So we should call the chained_irq_* each time enter sunxi_pinctrl_irq_handler().

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/85263ce8b058e80cea25c6ad6383eb256ce96cc8.1604988979.git.frank@allwinnertech.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The interrupt descriptor cannot be found in the interrupt processing
function, and this situation cannot happen when the system is running
normally. It doesn't seem right to return directly to the status of not
handling gic. In this case, it must be a bug, let's mark it with
WARN_ON.

Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/470ebae22fc5434ad5409c4f6e29255467b3cef6.1604988979.git.frank@allwinnertech.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

A100's pin starts with PB, so it should start with 1.

Fixes: 473436e7

 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/9db51667bf9065be55beafd56e5c319e3bbe8310.1604988979.git.frank@allwinnertech.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add initial pinctrl driver to support pin configuration with
pinctrl framework for SC7280 SoC

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1604570192-15057-2-git-send-email-rnayak@codeaurora.org


[Change select PINCTRL_MSM to depends on PINCTRL_MSM]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add device tree binding Documentation details for Qualcomm SC7280
TLMM block.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1604570192-15057-1-git-send-email-rnayak@codeaurora.org


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

One fixup following my patch commit be117ca3

 ("pinctrl:
qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then
a selected config") being queued in LinusW's tree, as a new
config entry was added for the msm8953 that also needs the
change.

Applies to LinusW's pinctrl devel tree.

Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Prasad Sodagudi <psodagud@codeaurora.org>
Cc: Vladimir Lypak <junak.pub@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201110215619.86076-1-john.stultz@linaro.org


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This reverts commit d0511b54

.

After some time it was noticed that the Tegra186 among others
were experiencing problems when making this into a module.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.

Link: https://github.com/KSPP/linux/issues/115


Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/da20103af0c22424c5d08a12f7107771bf4c01c5.1605896059.git.gustavoars@kernel.org


Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add pins, groups and functions for QSPIO[01].

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201119130926.25692-5-prabhakar.mahadev-lad.rj@bp.renesas.com


Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add pins, groups and functions for QSPIO[01].

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201119130926.25692-4-prabhakar.mahadev-lad.rj@bp.renesas.com


Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add pins, groups and functions for QSPIO[01].

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201119130926.25692-3-prabhakar.mahadev-lad.rj@bp.renesas.com


Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Add pins, groups and functions for QSPIO[01].

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201119130926.25692-2-prabhakar.mahadev-lad.rj@bp.renesas.com


Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

Since commit 4b563a06

 ("ARM: imx: Remove imx21 support") the imx21
SoC is no longer supported.

Get rid of its pinctrl driver too, which is now unused.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20201110190210.29376-1-festevam@gmail.com


Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'renesas-pinctrl-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: renesas: Updates for v5.11

  - Add remaining video-in (VIN) pin groups on R-Car H2 and RZ/G1H,
  - Image size optimizations and code consolidations,
  - Minor fixes and improvements.

Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.

Fixes: 658b476c ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a09 ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579

 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The only usage of sh73a0_vccq_mc0_ops is to assign its address to the
ops field in the regulator_desc struct, which is a const pointer. Make
it const to allow the compiler to put it in read-only memory.

Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201109221012.177478-1-rikard.falkeborn@gmail.com


Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>

On SuperH and ARM SH/R-Mobile SoCs, the pin control driver handles
GPIOs, too.  To reduce code size when compiling a kernel supporting only
modern SoCs, most, but not all, of the GPIO functionality is protected
by checks for CONFIG_PINCTRL_SH_FUNC_GPIO.

Factor out the remaining parts when not needed:
  1. sh_pfc_soc_info.{in,out}put describe GPIO pins that have input
     resp. output capabilities (SuperH and SH/R-Mobile).
  2. sh_pfc_soc_info.gpio_irq{,_size} describe the mapping from GPIO
     pins to interrupt numbers (SH/R-Mobile).
  3. sh_pfc_gpio_set_direction() configures GPIO direction, called from
     the GPIO driver through pinctrl_gpio_direction_{in,out}put()
     (SH/R-Mobile).  Unfortunately this function cannot just be moved to
     drivers/pinctrl/renesas/gpio.c, as it relies on knowledge of
     sh_pfc_pinctrl, which is internal to
     drivers/pinctrl/renesas/pinctrl.c.

While code size reduction is minimal, this does help in documenting
depencies.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-9-geert+renesas@glider.be

Currently, the rcar_pinmux_[gs]et_bias() helpers handle only SoCs that
have separate LSI Pin Pull-Enable (PUEN) and Pull-Up/Down Control (PUD)
registers, like R-Car Gen3 and RZ/G2.  Update the function to handle
SoCs that have only LSI Pin Pull-Up Control Register (PUPR), like R-Car
Gen1/Gen2 and RZ/G1.

Reduce code duplication by converting the R-Car M1A pin control driver
to use the common handler.

Note that this changes behavior in case the (invalid!) option
"bias-pull-down" is used in an R-Car M1A DTS: before, it was ignored
silently; after this change, it is considered the same as
"bias-pull-up".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-8-geert+renesas@glider.be

The handling of the LSI Pin Pull-Up Control Registers (PUPR) on R-Car
M1A uses register offsets instead of register physical addresses.
This is different from the handling on other R-Car parts.

Convert the bias handling from register offsets to physical addresses.
This increases uniformity, and prepares for consolidation of the bias
handling.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-7-geert+renesas@glider.be

All pin control drivers for R-Car Gen3 SoCs contain identical bias
handling.  Reduce code duplication by moving it to the common pinctrl.c
code.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-6-geert+renesas@glider.be

Shrink sh_pfc_pin_config from 8 to 2 bytes:
  - The mux_set flag can be removed, as a non-zero mark value means the
    same (zero = PINMUX_RESERVED is an invalid mark value),
  - The gpio_enabled flag needs only a single bit,
  - Mark values are small integers, and can easily fit in a 15-bit
    bitfield.

This saves 6 bytes per pin when allocating the sh_pfc_pinctrl.configs
array, i.e. it reduces run-time memory consumption by ca. 1.5 KiB.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-5-geert+renesas@glider.be

On arm64, pointer size and alignment is 64-bit, hence a 4-byte hole is
present in between the enum_id and name members of the sh_pfc_pin
structure.  Get rid of this hole by sorting the structure's members by
decreasing size.

This saves up to 1.5 KiB per enabled SoC, and reduces the size of a
kernel including support for all R-Car Gen3 SoCs by more than 10 KiB.

This has no size impact on SH and arm32.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-4-geert+renesas@glider.be