Add Chris Boot's i2c driver

i2c-bcm2708: fixed baudrate

Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock).
In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits.
This resulted in incorrect setting of CDIV and higher baudrate than intended.
Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz
After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz
The correct baudrate is shown in the log after the cdiv > 0xffff correction.

Perform I2C combined transactions when possible

Perform I2C combined transactions whenever possible, within the
restrictions of the Broadcomm Serial Controller.

Disable DONE interrupt during TA poll

Prevent interrupt from being triggered if poll is missed and transfer
starts and finishes.

i2c: Make combined transactions optional and disabled by default

i2c: bcm2708: add device tree support

Add DT support to driver and add to .dtsi file.
Setup pins in .dts file.
i2c is disabled by default.

Signed-off-by: Noralf Tronnes <notro@tronnes.org>

bcm2708: don't register i2c controllers when using DT

The devices for the i2c controllers are in the Device Tree.
Only register devices when not using DT.

Signed-off-by: Noralf Tronnes <notro@tronnes.org>

I2C: Only register the I2C device for the current board revision

i2c_bcm2708: Fix clock reference counting

Fix grabbing lock from atomic context in i2c driver

2 main changes:
- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment:
      /* poll for transfer start bit (should only take 1-20 polls) */
  This implies that the setup function can now fail so account for this everywhere it's called
- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock.

i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl

i2c-bcm2708: Increase timeouts to allow larger transfers

Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting
for completion. The default timeout is 1 second.

See: https://github.com/raspberrypi/linux/issues/260



i2c-bcm2708/BCM270X_DT: Add support for I2C2

The third I2C bus (I2C2) is normally reserved for HDMI use. Careless
use of this bus can break an attached display - use with caution.

It is recommended to disable accesses by VideoCore by setting
hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt.

The interface is disabled by default - enable using the
i2c2_iknowwhatimdoing DT parameter.

bcm2708-spi: Don't use static pin configuration with DT

Also remove superfluous error checking - the SPI framework ensures the
validity of the chip_select value.

i2c-bcm2708: Remove non-DT support

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs.

Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574)

* i2c: fix i2c_bcm2708: Clear FIFO before sending data

Make sure FIFO gets cleared before trying to send
data in case of a repeated start (COMBINED=Y).

* i2c: fix i2c_bcm2708: Only write to FIFO when not full

Check if FIFO can accept data before writing.
To avoid a peripheral read on the last iteration of a loop,
both bcm2708_bsc_fifo_fill and ~drain are changed as well.