MMC: added alternative MMC driver

mmc: Disable CMD23 transfers on all cards

Pending wire-level investigation of these types of transfers
and associated errors on bcm2835-mmc, disable for now. Fallback of
CMD18/CMD25 transfers will be used automatically by the MMC layer.

Reported/Tested-by: Gellert Weisz <gellert@raspberrypi.org>

mmc: bcm2835-mmc: enable DT support for all architectures

Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now.
Enable Device Tree support for all architectures.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

mmc: bcm2835-mmc: fix probe error handling

Probe error handling is broken in several places.
Simplify error handling by using device managed functions.
Replace pr_{err,info} with dev_{err,info}.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

bcm2835-mmc: Add locks when accessing sdhost registers

bcm2835-mmc: Add range of debug options for slowing things down

bcm2835-mmc: Add option to disable some delays

bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23

bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23

bcm2835-mmc: Adding overclocking option

Allow a different clock speed to be substitued for a requested 50MHz.
This option is exposed using the "overclock_50" DT parameter.
Note that the mmc interface is restricted to EVEN integer divisions of
250MHz, and the highest sensible option is 63 (250/4 = 62.5), the
next being 125 (250/2) which is much too high.

Use at your own risk.

bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz

Also only warn once for each overclock setting.

mmc: bcm2835-mmc: Make available on ARCH_BCM2835

Make the bcm2835-mmc driver available for use on ARCH_BCM2835.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

BCM270x_DT: add bcm2835-mmc entry

Add Device Tree entry for bcm2835-mmc.
In non-DT mode, don't add the device in the board file.

Signed-off-by: Noralf Trønnes <noralf@tronnes.org>

bcm2835-mmc: Don't overwrite MMC capabilities from DT

bcm2835-mmc: Don't override bus width capabilities from devicetree

Take out the force setting of the MMC_CAP_4_BIT_DATA host capability
so that the result read from devicetree via mmc_of_parse() is
preserved.

bcm2835-mmc: Only claim one DMA channel

With both MMC controllers enabled there are few DMA channels left. The
bcm2835-mmc driver only uses DMA in one direction at a time, so it
doesn't need to claim two channels.

See: https://github.com/raspberrypi/linux/issues/1327



Signed-off-by: Phil Elwell <phil@raspberrypi.org>

bcm2835-mmc: New timer API

mmc: bcm2835-mmc: Support underclocking

Support underclocking of the SD bus using the max-frequency DT property
(which currently has no DT parameter). The sd_overclock parameter
already provides another way to achieve the same thing which should be
equivalent in end result, but it is a bug not to support max-frequency
as well.

See: https://github.com/raspberrypi/linux/issues/2350



Signed-off-by: Phil Elwell <phil@raspberrypi.org>

mmc/bcm2835: Recover from MMC_SEND_EXT_CSD

If the user issues an "mmc extcsd read", the SD controller receives
what it thinks is a SEND_IF_COND command with an unexpected data block.
The resulting operations leave the FSM stuck in READWAIT, a state which
persists until the MMC framework resets the controller, by which point
the root filesystem is likely to have been unmounted.

A less heavyweight solution is to detect the condition and nudge the
FSM by asserting the (self-clearing) FORCE_DATA_MODE bit.

N.B. This workaround was essentially discovered by accident and without
a full understanding the inner workings of the controller, so it is
fortunate that the "fix" only modifies error paths.

See: https://github.com/raspberrypi/linux/issues/2728



Signed-off-by: Phil Elwell <phil@raspberrypi.org>

bcm2835-mmc: Fix DMA channel leak

The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path and on driver unbind.

I'm seeing this happen on every boot of the Compute Module 3: On first
driver probe, DMA channel 2 is allocated and then leaked with a "could
not get clk, deferring probe" message. On second driver probe, channel 4
is allocated.

Fix it.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>

bcm2835-mmc: Fix struct mmc_host leak on probe

The BCM2835 MMC host driver requests the bus address of the host's
register map on probe.  If that fails, the driver leaks the struct
mmc_host allocated earlier.

Fix it.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>

bcm2835-mmc: Fix duplicate free_irq() on remove

The BCM2835 MMC host driver requests its interrupt as a device-managed
resource, so the interrupt is automatically freed after the driver is
unbound.

However on driver unbind, bcm2835_mmc_remove() frees the interrupt
explicitly to avoid invocation of the interrupt handler after driver
structures have been torn down.

The interrupt is thus freed twice, leading to a WARN splat in
__free_irq().  Fix by not requesting the interrupt as a device-managed
resource.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>

bcm2835-mmc: Handle mmc_add_host() errors

The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its
return value.  Errors occurring in that function are therefore not
handled.  Fix it.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>

bcm2835-mmc: Deduplicate reset of driver data on remove

The BCM2835 MMC host driver sets the device's driver data pointer to
NULL on ->remove() even though the driver core subsequently does the
same in __device_release_driver().  Drop the duplicate assignment.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>

bcm2835_mmc: Remove vestigial threaded IRQ

With SDIO processing now managed by the MMC framework with a
workqueue, the bcm2835_mmc driver no longer needs a threaded
IRQ.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>

Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers.
This prevents DMA leaks.

Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>

Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing.

Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>