Either the docs were wrong or the values have changed since the old days
before we had wheels.

Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

It's possible that the CCK clock could run at a different rate than the
DDR clock, so use the same method to get CCK as the GMBUS code does when
calculating the new CDclk divider in the VLV display code.

Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On VLV/BYT, we can adjust the CDclk frequency up or down based on the
max pixel clock we need to drive.  Lowering it can save power, while
raising it is necessary to support high resolution.

Add a new callback in modeset_affected_pipes and a
modeset_global_resources function to perform this adjustment as
necessary.

v2: use punit interface for 320 and 266 MHz CDclk adjustments (Ville)
v3: reset GMBUS dividers too, since we changed CDclk (Ville)
v4: jump to highest voltage when going to 400MHz CDclk (Jesse)
v5: drop duplicate define (Ville)
    use shifts by 1 for fixed point (Ville)
    drop new callback (Daniel)
v6: fixup adjusted_mode.clock -> adjusted_mode.crtc_clock again (Ville)
    document Bunit reg access better (Ville)
v7: pass modeset_pipes and pipe_config to global_pipes so we get the right
    clock data (Ville)

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We don't want it delayed with the RPS work.

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

For modifying self-refresh exit latency.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

With the change in the modeset sequence this shouldn't be required
any more since the ->mode_set callback now gets called when the dvo
port is fully up and running.

Also limit the retry loop to 10 tries to avoid hanging the machine
while holding important modeset locks.

Cc: Thomas Richter <thor@math.tu-berlin.de>
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

The ns2501 controller seems to need the dpll and dvo port to accept
the timing update commands. Quick testing on my x30 here seems to
indicate that other dvo controllers don't mind. So let's move the
->mode_set callback to a place where we have the port up and running
already.

Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Thomas Richter <thor@math.tu-berlin.de>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.

We'll propably have some fun because Linus will come up with a
slightly different merge solution.

Conflicts:
	drivers/gpu/drm/i915/i915_dma.c
	drivers/gpu/drm/i915/i915_drv.c
	drivers/gpu/drm/i915/intel_crt.c
	drivers/gpu/drm/i915/intel_ddi.c
	drivers/gpu/drm/i915/intel_display.c
	drivers/gpu/drm/i915/intel_dp.c
	drivers/gpu/drm/i915/intel_drv.h

All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.

Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.

v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Pull MIPS fixes from Ralf Baechle:
 "Three fixes across arch/mips with the most complex one being the GIC
  interrupt fix - at nine lines still not monster.  I'm confident this
  are the final MIPS patches even if there should go for an rc8"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: fix return value check in rt_timer_probe()
  MIPS: malta: Fix GIC interrupt offsets
  MIPS: Perf: Fix 74K cache map

Negative message lengths make no sense -- so don't do negative queue
lenghts or identifier counts. Prevent them from getting negative.

Also change the underlying data types to be unsigned to avoid hairy
surprises with sign extensions in cases where those variables get
evaluated in unsigned expressions with bigger data types, e.g size_t.

In case a user still wants to have "unlimited" sizes she could just use
INT_MAX instead.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ARM kallsyms fix from Rusty Russell:
 "Last minute perf unbreakage for ARM modules; spent a day in
  linux-next"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
  scripts/kallsyms: filter symbols not in kernel address space

A vmalloc fault needs to sync up PGD/PTE entry from init_mm to current
task's "active_mm".  ARC vmalloc fault handler however was using mm.

A vmalloc fault for non user task context (actually pre-userland, from
init thread's open for /dev/console) caused the handler to deref NULL mm
(for mm->pgd)

The reasons it worked so far is amazing:

1. By default (!SMP), vmalloc fault handler uses a cached value of PGD.
   In SMP that MMU register is repurposed hence need for mm pointer deref.

2. In pre-3.12 SMP kernel, the problem triggering vmalloc didn't exist in
   pre-userland code path - it was introduced with commit 20bafb3d
   "n_tty: Move buffers into n_tty_data"

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: stable@vger.kernel.org    #3.10 and 3.11
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch uses CONFIG_PAGE_OFFSET to filter symbols which
are not in kernel address space because these symbols are
generally for generating code purpose and can't be run at
kernel mode, so we needn't keep them in /proc/kallsyms.

For example, on ARM there are some symbols which may be
linked in relocatable code section, then perf can't parse
symbols any more from /proc/kallsyms, this patch fixes the
problem (introduced b9b32bf7)

Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Michal Marek <mmarek@suse.cz>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@vger.kernel.org

Pull perf fixes from Ingo Molnar:
 "Two fixes:

   - Fix 'NMI handler took too long to run' false positives

     [ Genuine NMI overhead speedups will come for v3.13, this commit
       only fixes a measurement bug ]

   - Fix perf ring-buffer missed barrier causing (rare) ring-buffer data
     corruption on ppc64"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86: Fix NMI measurements
  perf: Fix perf ring buffer memory ordering

Pull USB fixes from Greg KH:
 "Here is a set of patches that revert all of the changes done to the
  pl2303 USB serial driver in the 3.12-rc timeframe, as it turns out
  they break some devices that work just fine on 3.11.  As it's not a
  good idea to break working systems, drop them all and they will be
  reworked for future kernel versions such that there is no breakage.

  I've also included a MAINTAINERS update for the USB serial subsystem
  and a new device id for the ftdi_sio driver as well"

* tag 'usb-3.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: serial: ftdi_sio: add id for Z3X Box device
  USB: Maintainers change for usb serial drivers
  Revert "USB: pl2303: restrict the divisor based baud rate encoding method to the "HX" chip type"
  Revert "usb: pl2303: fix+improve the divsor based baud rate encoding method"
  Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"
  Revert "usb: pl2303: remove 500000 baud from the list of standard baud rates"
  Revert "usb: pl2303: move the two baud rate encoding methods to separate functions"
  Revert "usb: pl2303: increase the allowed baud rate range for the divisor based encoding method"
  Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"
  Revert "usb: pl2303: add two comments concerning the supported baud rates with HX chips"
  Revert "pl2303: simplify the else-if contruct for type_1 chips in pl2303_startup()"
  Revert "pl2303: improve the chip type information output on startup"
  Revert "pl2303: improve the chip type detection/distinction"
  Revert "USB: pl2303: distinguish between original and cloned HX chips"

Pull more sound fixes from Takashi Iwai:
 "The fixes for random bugs that have been reported lately in the game:
  a few fixes in ASoC dpam and wm_hubs bugs spotted by Coverity, a
  one-liner HD-audio fixup, and a fix for Oops with DPCM.

  They are not so critically urgent bugs, but all small and safe"

* tag 'sound-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: fix oops in snd_pcm_info() caused by ASoC DPCM
  ASoC: wm_hubs: Add missing break in hp_supply_event()
  ALSA: hda - Add a fixup for ASUS N76VZ
  ASoC: dapm: Return -ENOMEM in snd_soc_dapm_new_dai_widgets()
  ASoC: dapm: Fix source list debugfs outputs

Pull clock subsystem fixes from Mike Turquette.

* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mturquette/linux:
  clk: fixup argument order when setting VCO parameters
  clk: socfpga: Fix incorrect sdmmc clock name
  clk: armada-370: fix tclk frequencies
  clk: nomadik: set all timers to use 2.4 MHz TIMCLK

When a memcg is deleted mem_cgroup_reparent_charges() moves charged
memory to the parent memcg.  As of v3.11-9444-g3ea67d0 "memcg: add per
cgroup writeback pages accounting" there's bad pointer read.  The goal
was to check for counter underflow.  The counter is a per cpu counter
and there are two problems with the code:

 (1) per cpu access function isn't used, instead a naked pointer is used
     which easily causes oops.
 (2) the check doesn't sum all cpus

Test:
  $ cd /sys/fs/cgroup/memory
  $ mkdir x
  $ echo 3 > /proc/sys/vm/drop_caches
  $ (echo $BASHPID >> x/tasks && exec cat) &
  [1] 7154
  $ grep ^mapped x/memory.stat
  mapped_file 53248
  $ echo 7154 > tasks
  $ rmdir x
  <OOPS>

The fix is to remove the check.  It's currently dangerous and isn't
worth fixing it to use something expensive, such as
percpu_counter_sum(), for each reparented page.  __this_cpu_read() isn't
enough to fix this because there's no guarantees of the current cpus
count.  The only guarantees is that the sum of all per-cpu counter is >=
nr_pages.

Fixes: 3ea67d06 ("memcg: add per cgroup writeback pages accounting")
Reported-and-tested-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Greg Thelen <gthelen@google.com>
Reviewed-by: Sha Zhengju <handai.szj@taobao.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Even though we only check for unclaimed registers while we're writing
registers, if we read a bad register we'll still trigger a CPU error
interrupt, and we'll print an "Unclaimed register" DRM_ERROR due to
that. To avoid this error, just avoid touching power domains that are
not enabled.

Use kzalloc so we're sure all the disabled domains will be zeroed on
the error state file. We already print the information that is enough
to discover if the power well is enabled on the error state file, so
this should not be a problem.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=69747


Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Now that DP port CRCs are stable, we can use it for generic CRC tests.
Yay, the auto CRC source should now work everywhere!

Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

They've moved the DC balance reset bit around. Again I don't think we
need it, but better safe than sorry and maybe HDMI port CRC will prove
useful for checking infoframes or hdmi audio.

v2: Apply the suggestions from Damien's review.

Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

We need to reset the DP scrambler on every vsync to get stable CRCs.
And since we can't use the normal pipe CRC on DP ports on g4x we
really need them to be able to test modesetting issues on (e)DP
outputs.

Note that the DC balance reset is for SDVO port CRCs so we don't
strictly need it. But better safe than sorry (and it's a nice template
in case we ever want to grab port CRCs for e.g. audio checking).

v2: Apply the suggestions from Damien's review.

Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

On gmch platforms the normal pipe source CRC registers don't work for
DP and TV encoders. And on newer platforms the single pipe CRC has
been replaced by a set of CRC at different stages in the platform.

Now most of our userspace tests don't care one bit about the exact
CRC, they simply want something that reflects any changes on the
screen. Hence add a new auto target for platform agnostic tests to
use.

v2: Pass back the adjusted source so that it can be shown in debugfs.

v3: I seem to be unable to get a stable CRC for DP ports. So let's
just disable them for now when using the auto mode. Note that
testcases need to be restructured so that they can dynamically skip
connectors. They also first need to set up the desired mode
configuration, since otherwise the auto mode won't do the right thing.

v4: Don't leak the modeset mutex on error paths.

v5: Spelling fix for the i9xx auto_source function.

Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Custom VID/PID for Z3X Box device, popular tool for cellphone flashing.

Signed-off-by: Alexey E. Kramarenko <alexeyk13@yandex.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Johan has been conned^Wgracious in accepting the maintainership of the
USB serial drivers, especially as he's been doing all of the real work
for the past few years.

At the same time, remove a bunch of old entries for USB serial drivers
that don't make sense anymore, given that the developers are no longer
around, and individual driver maintainerships for tiny things like this
is pretty pointless.

Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b8bdad60.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 57ce61aa.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: do not round to the next nearest standard baud rate for the divisor based baud rate encoding method"

This reverts commit 75417d9f.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b9208c72.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e917ba01.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit b5c16c6a.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "usb: pl2303: also use the divisor based baud rate encoding method for baud rates < 115200 with HX chips"

This reverts commit 61fa8d69.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit c23bda36.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 73b583af.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit a77a8c23.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 034d1527.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 7d26a78f.

Revert all of the pl2303 changes that went into 3.12-rc1 and -rc2 as
they cause regressions on some versions of the chip.  This will all be
revisited for later kernel versions when we can figure out how to handle
this in a way that does not break working devices.

Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge four more fixes from Andrew Morton.

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  lib/scatterlist.c: don't flush_kernel_dcache_page on slab page
  mm: memcg: fix test for child groups
  mm: memcg: lockdep annotation for memcg OOM lock
  mm: memcg: use proper memcg in limit bypass

Commit b1adaf65 ("[SCSI] block: add sg buffer copy helper
functions") introduces two sg buffer copy helpers, and calls
flush_kernel_dcache_page() on pages in SG list after these pages are
written to.

Unfortunately, the commit may introduce a potential bug:

 - Before sending some SCSI commands, kmalloc() buffer may be passed to
   block layper, so flush_kernel_dcache_page() can see a slab page
   finally

 - According to cachetlb.txt, flush_kernel_dcache_page() is only called
   on "a user page", which surely can't be a slab page.

 - ARCH's implementation of flush_kernel_dcache_page() may use page
   mapping information to do optimization so page_mapping() will see the
   slab page, then VM_BUG_ON() is triggered.

Aaro Koskinen reported the bug on ARM/kirkwood when DEBUG_VM is enabled,
and this patch fixes the bug by adding test of '!PageSlab(miter->page)'
before calling flush_kernel_dcache_page().

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tejun Heo <tj@kernel.org>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>	[3.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>