Merge tag 'wireless-drivers-next-2021-04-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next



Kalle Valo says:

====================
wireless-drivers-next patches for v5.13

Third, and final, set of patches for v5.13. We got one more week
before the merge window and this includes from that extra week.
Smaller features to rtw88 and mt76, but mostly this contains fixes.

rtw88

* 8822c: Add gap-k calibration to improve long range performance

mt76

* parse rate power limits from DT

* debugfs file to test firmware crash

* debugfs to disable NAPI threaded mode
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: adjust REALTEK_USB_DEVICE

Modify REALTEK_USB_DEVICE macro.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Redefine REALTEK_USB_DEVICE macro with USB_DEVICE_INTERFACE_CLASS and
USB_DEVICE_AND_INTERFACE_INFO to simply the code.

Although checkpatch.pl shows the following error, it is more readable.

	ERROR: Macros with complex values should be enclosed in parentheses

Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The RTL8156 support CDC NCM mode. And users could set the configuration
of the USB device between vendor and NCM mode dynamically by themselves.
That is, the driver doesn't need to set vendor mode from NCM mode.

Fixes: 195aae32

 ("r8152: support new chips")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The previous patch to support PTP Sync packet one-step timestamping
described one-step timestamping packet handling logic as below in
commit message:

- Trasmit packet immediately if no other one in transfer, or queue to
  skb queue if there is already one in transfer.
  The test_and_set_bit_lock() is used here to lock and check state.
- Start a work when complete transfer on hardware, to release the bit
  lock and to send one skb in skb queue if has.

There was not problem of the description, but there was a mistake in
implementation. The locking/test_and_set_bit_lock() should be put in
enetc_start_xmit() which may be called by worker, rather than in
enetc_xmit(). Otherwise, the worker calling enetc_start_xmit() after
bit lock released is not able to lock again for transfer.

Fixes: 7294380c

 ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2021-04-23

1) The SPI flow key in struct flowi has no consumers,
   so remove it. From Florian Westphal.

2) Remove stray synchronize_rcu from xfrm_init.
   From Florian Westphal.

3) Use the new exit_pre hook to reset the netlink socket
   on net namespace destruction. From Florian Westphal.

4) Remove an unnecessary get_cpu() in ipcomp, that
   code is always called with BHs off.
   From Sabrina Dubroca.

Please pull or let me know if there are problems.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Ilya Lipnitskiy says:

====================
mtk_eth_soc: fixes and performance improvements

Most of these changes come from OpenWrt where they have been present and
tested for months.

First three patches are bug fixes. The rest are performance
improvements. The last patch is a cleanup to use the iopoll.h macro for
busy-waiting instead of a custom loop.

v2:
 - Reverse christmas tree in "use iopoll.h macro for DMA init"
 - Use cond_resched() instead of iopoll.h macro in "reduce MDIO bus
   access latency"
 - Use napi_complete_done and rework NAPI callbacks in a new patch
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Replace a tight busy-wait loop without a pause with a standard
readx_poll_timeout_atomic routine with a 5 us poll period.

Tested by booting a MT7621 device to ensure the driver initializes
properly.

Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This improves GRO performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: Use MTK_RXD4_FOE_ENTRY instead of GENMASK(13, 0)]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use napi_complete_done to communicate total TX and RX work done to NAPI.
Count total RX work up instead of remaining work down for clarity.
Remove unneeded local variables for clarity. Use do {} while instead of
goto for clarity.

Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid rearming interrupt if napi_complete returns false

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Uncached memory access is expensive, and there is no need to access all
descriptor words if we can't process them anyway

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The value is only updated by the CPU, so it is cheaper to access from the
ring data structure than from a hardware register.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduces the number of interrupts under load

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: add documentation for new struct fields]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

256 descriptors is not enough for multi-gigabit traffic under load on
MT7622. Bump it to 512 to improve performance.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improves tx performance

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running short on descriptors, only stop the queue for the netdev that
tx was attempted for. By the time something tries to send on the other
netdev, the ring might have some more room already.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

usleep_range often ends up sleeping much longer than the 10-20us provided
as a range here. This causes significant latency in mdio bus acceses,
which easily adds multiple seconds to the boot time on MT7621 when polling
DSA slave ports.
Use cond_resched instead of usleep_range, since the MDIO access does not
take much time

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Should improve performance, since it can use bulk free

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case build_skb fails, call skb_free_frag on the correct pointer. Also
update the DMA structures with the new mapping before exiting, because
the mapping was successful

Suggested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since build_skb accesses the data area (for initializing shinfo), dma unmap
needs to happen before that call

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: split build_skb cleanup fix into a separate commit]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mana_gd_poll_cq() may return -1 if an overflow error is detected (this
should never happen unless there is a bug in the driver or the hardware).

Fix the type of the variable "comp_read" by using int rather than u32.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: ca9c54d2

 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When "headroom" > 0, the actual allocated memory space is the entire
page, so the address of the page should be used when passing it to
build_skb().

BUG: KASAN: use-after-free in skb_gro_receive (net/core/skbuff.c:4260)
Write of size 16 at addr ffff88811619fffc by task kworker/u9:0/534
CPU: 2 PID: 534 Comm: kworker/u9:0 Not tainted 5.12.0-rc7-custom-16372-gb150be05b806 #3382
Hardware name: QEMU MSN2700, BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Workqueue: xprtiod xs_stream_data_receive_workfn [sunrpc]
Call Trace:
 <IRQ>
dump_stack (lib/dump_stack.c:122)
print_address_description.constprop.0 (mm/kasan/report.c:233)
kasan_report.cold (mm/kasan/report.c:400 mm/kasan/report.c:416)
skb_gro_receive (net/core/skbuff.c:4260)
tcp_gro_receive (net/ipv4/tcp_offload.c:266 (discriminator 1))
tcp4_gro_receive (net/ipv4/tcp_offload.c:316)
inet_gro_receive (net/ipv4/af_inet.c:1545 (discriminator 2))
dev_gro_receive (net/core/dev.c:6075)
napi_gro_receive (net/core/dev.c:6168 net/core/dev.c:6198)
receive_buf (drivers/net/virtio_net.c:1151) virtio_net
virtnet_poll (drivers/net/virtio_net.c:1415 drivers/net/virtio_net.c:1519) virtio_net
__napi_poll (net/core/dev.c:6964)
net_rx_action (net/core/dev.c:7033 net/core/dev.c:7118)
__do_softirq (./arch/x86/include/asm/jump_label.h:25 ./include/linux/jump_label.h:200 ./include/trace/events/irq.h:142 kernel/softirq.c:346)
irq_exit_rcu (kernel/softirq.c:221 kernel/softirq.c:422 kernel/softirq.c:434)
common_interrupt (arch/x86/kernel/irq.c:240 (discriminator 14))
</IRQ>

Fixes: fb32856b

 ("virtio-net: page_to_skb() use build_skb when there's sufficient tailroom")
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Reported-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tw_prot_cleanup will check the twsk_prot.

Fixes: 0f5907af

 ("net: Fix potential memory leak in proto_register()")
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Mohammad Athari Bin Ismail says:

====================
Enable DWMAC HW descriptor prefetch

This patch series to add setting for HW descriptor prefetch for DWMAC
version 5.20 onwards. For Intel platform, enable the capability by
default.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Enable HW descriptor prefetch by default by setting plat->dma_cfg->dche =
true in intel_mgbe_common_data(). Need to be noted that this capability
only be supported in DWMAC core version 5.20 onwards. In stmmac, there is
a checking to check the core version. If the core version is below 5.20,
this capability wouldn`t be configured.

Below is the iperf result comparison between HW descriptor prefetch
disabled(DCHE=0b) and enabled(DCHE=1b). Tested on Intel Elkhartlake
platform with DWMAC Core 5.20. Observed line rate performance
improvement with HW descriptor prefetch enabled.

DCHE = 0b
[  5] local 169.254.1.162 port 42123 connected to 169.254.244.142 port 5201
[ ID] Interval           Transfer     Bitrate         Total Datagrams
[  5]   0.00-1.00   sec  96.7 MBytes   811 Mbits/sec  70050
[  5]   1.00-2.00   sec  96.5 MBytes   809 Mbits/sec  69850
[  5]   2.00-3.00   sec  96.3 MBytes   808 Mbits/sec  69720
[  5]   3.00-4.00   sec  95.9 MBytes   804 Mbits/sec  69450
[  5]   4.00-5.00   sec  96.0 MBytes   806 Mbits/sec  69530
[  5]   5.00-6.00   sec  96.8 MBytes   812 Mbits/sec  70080
[  5]   6.00-7.00   sec  96.9 MBytes   813 Mbits/sec  70140
[  5]   7.00-8.00   sec  96.8 MBytes   812 Mbits/sec  70080
[  5]   8.00-9.00   sec  97.0 MBytes   814 Mbits/sec  70230
[  5]   9.00-10.00  sec  96.9 MBytes   813 Mbits/sec  70170
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
[  5]   0.00-10.00  sec   966 MBytes   810 Mbits/sec  0.000 ms  0/699300 (0%)  sender
[  5]   0.00-10.00  sec   966 MBytes   810 Mbits/sec  0.011 ms  0/699265 (0%)  receiver

DCHE = 1b
[  5] local 169.254.1.162 port 49740 connected to 169.254.244.142 port 5201
[ ID] Interval           Transfer     Bitrate         Total Datagrams
[  5]   0.00-1.00   sec  97.9 MBytes   821 Mbits/sec  70880
[  5]   1.00-2.00   sec  98.1 MBytes   823 Mbits/sec  71060
[  5]   2.00-3.00   sec  98.2 MBytes   824 Mbits/sec  71140
[  5]   3.00-4.00   sec  98.2 MBytes   824 Mbits/sec  71090
[  5]   4.00-5.00   sec  98.1 MBytes   823 Mbits/sec  71050
[  5]   5.00-6.00   sec  98.1 MBytes   823 Mbits/sec  71040
[  5]   6.00-7.00   sec  98.1 MBytes   823 Mbits/sec  71050
[  5]   7.00-8.00   sec  98.2 MBytes   824 Mbits/sec  71140
[  5]   8.00-9.00   sec  98.2 MBytes   824 Mbits/sec  71120
[  5]   9.00-10.00  sec  98.3 MBytes   824 Mbits/sec  71150
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval           Transfer     Bitrate         Jitter    Lost/Total Datagrams
[  5]   0.00-10.00  sec   981 MBytes   823 Mbits/sec  0.000 ms  0/710720 (0%)  sender
[  5]   0.00-10.00  sec   981 MBytes   823 Mbits/sec  0.041 ms  0/710650 (0%) receiver

Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).

So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured

Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Handling comm_channel_event in mlx4_master_comm_channel uses a double
loop to determine which slaves have requested work. The search is
always started at lowest slave. This leads to unfairness; lower VFs
tends to be prioritized over higher VFs.

The patch uses find_next_bit to determine which slaves to handle.
Fairness is implemented by always starting at the next to the last
start.

An MPI program has been used to measure improvements. It runs 500
ibv_reg_mr, synchronizes with all other instances and then runs 500
ibv_dereg_mr.

The results running 500 processes, time reported is for running 500
calls:

ibv_reg_mr:
             Mod.   Org.
mlx4_1    403.356ms 424.674ms
mlx4_2    403.355ms 424.674ms
mlx4_3    403.354ms 424.674ms
mlx4_4    403.355ms 424.674ms
mlx4_5    403.357ms 424.677ms
mlx4_6    403.354ms 424.676ms
mlx4_7    403.357ms 424.675ms
mlx4_8    403.355ms 424.675ms

ibv_dereg_mr:
             Mod.   Org.
mlx4_1    116.408ms 142.818ms
mlx4_2    116.434ms 142.793ms
mlx4_3    116.488ms 143.247ms
mlx4_4    116.679ms 143.230ms
mlx4_5    112.017ms 107.204ms
mlx4_6    112.032ms 107.516ms
mlx4_7    112.083ms 184.195ms
mlx4_8    115.089ms 190.618ms

Suggested-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the timeout occurs, we still have to run the following process
for releasing patch request. Otherwise, the PHY would keep no link.
Therefore, use break to stop the loop of loading firmware and
release the patch request rather than return the function directly.

Fixes: 4a51b0e8

 ("r8152: support PHY firmware for RTL8156 series")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2021-04-22

This series contains updates to virtchnl header file, ice, and iavf
drivers.

Vignesh adds support to warn about potentially malicious VFs; those that
are overflowing the mailbox for the ice driver.

Michal adds support for an allowlist/denylist of VF commands based on
supported capabilities for the ice driver.

Brett adds support for iavf UDP segmentation offload by adding the
capability bit to virtchnl, advertising support in the ice driver, and
enabling it in the iavf driver. He also adds a helper function for
getting the VF VSI for ice.

Colin Ian King removes an unneeded pointer assignment.

Qi enables support in the ice driver to support virtchnl requests from
the iavf to configure its own RSS input set. This includes adding new
capability bits, structures, and commands to virtchnl header file.

Haiyue enables configuring RSS flow hash via ethtool to support TCP, UDP
and SCTP protocols in iavf.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

There are a few warnings about empty debug macros in this driver:

drivers/net/ethernet/neterion/vxge/vxge-main.c: In function 'vxge_probe':
drivers/net/ethernet/neterion/vxge/vxge-main.c:4480:76: error: suggest braces around empty body in an 'if' statement [-Werror=empty-body]
 4480 |                                 "Failed in enabling SRIOV mode: %d\n", ret);

Change them to proper 'do { } while (0)' expressions to make the
code a little more robust and avoid the warnings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensure that the poll system call returns proper error flags when port
is removed (nullified port ops), allowing user side to properly fail,
without further read or write.

Fixes: 9a44c1cc

 ("net: Add a WWAN subsystem")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the sampling truncation length is invalid (zero), pass the length
of the packet. Without the fix, no payload is reported to user space
when the truncation length is zero.

Fixes: a8700c3d

 ("netdevsim: Add dummy psample implementation")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

A link time bug that I had fixed before has come back now that
another sub-module was added to the enetc driver:

ERROR: modpost: "enetc_ierb_register_pf" [drivers/net/ethernet/freescale/enetc/fsl-enetc.ko] undefined!

The problem is that the enetc Makefile is not actually used for
the ierb module if that is the only built-in driver in there
and everything else is a loadable module.

Fix it by always entering the directory this time, regardless
of which symbols are configured. This should reliably fix the
problem and prevent it from coming back another time.

Fixes: 112463dd ("net: dsa: felix: fix link error")
Fixes: e7d48e5f

 ("net: enetc: add a mini driver for the Integrated Endpoint Register Block")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MANA driver causes a build failure in some configurations when
it selects an unavailable symbol:

WARNING: unmet direct dependencies detected for PCI_HYPERV
  Depends on [n]: PCI [=y] && X86_64 [=y] && HYPERV [=n] && PCI_MSI [=y] && PCI_MSI_IRQ_DOMAIN [=y] && SYSFS [=y]
  Selected by [y]:
  - MICROSOFT_MANA [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROSOFT [=y] && PCI_MSI [=y] && X86_64 [=y]
drivers/pci/controller/pci-hyperv.c: In function 'hv_irq_unmask':
drivers/pci/controller/pci-hyperv.c:1217:9: error: implicit declaration of function 'hv_set_msi_entry_from_desc' [-Werror=implicit-function-declaration]
 1217 |         hv_set_msi_entry_from_desc(&params->int_entry.msi_entry, msi_desc);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~

A PCI driver should never depend on a particular host bridge
implementation in the first place, but if we have this dependency
it's better to express it as a 'depends on' rather than 'select'.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide the ability to enable SCTP RSS hashing by ethtool.

It gives users option of generating RSS hash based on the SCTP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Provides the ability to enable UDP RSS hashing by ethtool.

It gives users option of generating RSS hash based on the UDP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Provides the ability to enable TCP RSS hashing by ethtool.

It gives users option of generating RSS hash based on the TCP source
and destination ports numbers, IPv4 or IPv6 source and destination
addresses.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Add the virtchnl message interface to VF, so that VF can request RSS
input set(s) based on PF's capability.

This framework allows ethtool RSS config support on the VF driver.

Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>