In thunderbolt mode the PHY is owned by the thunderbolt controller.
We are not supposed to touch it. So skip the vswing programming
as well (we already skipped the other steps not applicable to TBT).

Touching this stuff could supposedly interfere with the PHY
programming done by the thunderbolt controller.

Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128155948.13678-1-ville.syrjala@linux.intel.com


Reviewed-by: Imre Deak <imre.deak@intel.com>

Atm, the driver programs explicitly the default transparent link
training mode (0x55) to DP_PHY_REPEATER_MODE even if no LTTPRs are
detected.

This conforms to the spec (3.6.6.1):
"DP upstream devices that do not enable the Non-transparent mode of
 LTTPRs shall program the PHY_REPEATER_MODE register (DPCD Address
 F0003h) to 55h (default) prior to link training"

however writing the default value to this DPCD register seems to cause
occasional link training errors at least for a DELL WD19TB TBT dock, when
no LTTPRs are detected.

Writing to DP_PHY_REPEATER_MODE will also cause an unnecessary timeout
on systems without any LTTPR.

To fix the above two issues let's assume that setting the default mode
is redundant when no LTTPRs are detected. Keep the existing behavior and
program the default mode if more than 8 LTTPRs are detected or in case
the read from DP_PHY_REPEATER_CNT returns an invalid value.

References: https://gitlab.freedesktop.org/drm/intel/-/issues/2801


Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210118183143.1145707-1-imre.deak@intel.com

Add support for async flips on vlv/chv. Unlike all the other
platforms vlv/chv do not use the async flip bit in DSPCNTR and
instead we select between async vs. sync flips based on the
surface address register. The normal DSPSURF generates sync
flips DSPADDR_VLV generates async flips. And as usual the
interrupt bits are different from the other platforms.

Cc: Karthik B S <karthik.b.s@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111163711.12913-12-ville.syrjala@linux.intel.com


Reviewed-by: Karthik B S <karthik.b.s@intel.com>

Add support for async flips on ivb/hsw. Again no need for any
workarounds and just have to deal with the interrupt bits being
shuffled around a bit.

Cc: Karthik B S <karthik.b.s@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111163711.12913-11-ville.syrjala@linux.intel.com


Reviewed-by: Karthik B S <karthik.b.s@intel.com>

Add support for async flips on ivb/hsw. Unlike bdw+ we don't need
any workarounds to disable async flips. Apart from that the only
real difference from the bdw implementation is the location of the
flip_done interrupt bits.

Cc: Karthik B S <karthik.b.s@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111163711.12913-10-ville.syrjala@linux.intel.com


Reviewed-by: Karthik B S <karthik.b.s@intel.com>

Implement async flip support for BDW. The implementation is
similar to the skl+ code. And just like skl/bxt/glk bdw also
needs the disable w/a, thus we need to plumb the desired state
of the async flip all the way down to i9xx_plane_ctl_crtc().

According to the spec we do need to bump the surface alignment
to 256KiB for this. Async flips require an X-tiled buffer so
we don't have to worry about linear.

Cc: Karthik B S <karthik.b.s@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111163711.12913-9-ville.syrjala@linux.intel.com


Reviewed-by: Karthik B S <karthik.b.s@intel.com>

Limit pre-skl plane stride to below 4k or 8k pixels (depending on
the platform). We do this in order guarantee that TILEOFF/OFFSET.x
does not get too big.

Currently this is not a problem as we align SURF to 4k, and so
TILEOFF/OFFSET only have to deal with a single tile's worth of
pixels. But for async flips we're going to have to bump SURF
alignment to 256k, and thus we can no longer guarantee
TILEOFF/OFFSET.x will stay within acceptable bounds. We can avoid
this by borrowing a trick from the skl+ code and limit the max
plane stride to whatever value we can fit into TILEOFF/OFFSET.x.

The slight downside is that we may end up doing GTT remapping in
a few more cases where previously we did not have to. But since
that will only happen with huge buffers I'm not really concerned
about it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111163711.12913-3-ville.syrjala@linux.intel.com


Reviewed-by: Karthik B S <karthik.b.s@intel.com>

As it now it is always required for GEN12+ the is_16gb_dimm name
do not make sense for GEN12+.

v2:
- Updated comment on top of "dram_info->wm_lv_0_adjust_needed =
!IS_GEN9_LP(i915);"

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128164312.91160-3-jose.souza@intel.com

Up to now we were reading some DRAM information from MCHBAR register
and from pcode what is already not good but some GEN12(TGL-H and ADL-S)
platforms have MCHBAR DRAM information in different offsets.

This was notified to HW team that decided that the best alternative is
always apply the 16gb_dimm watermark adjustment for GEN12+ platforms
and read the remaning DRAM information needed to other display
programming from pcode.

So here moving the DRAM pcode function to intel_dram.c, removing
the duplicated fields from intel_qgv_info, setting and using
information from dram_info.

v2:
- bring back num_points to intel_qgv_info as num_qgv_point can be
overwritten in icl_get_qgv_points()
- add gen12_get_dram_info() and simplify gen11_get_dram_info()

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128164312.91160-2-jose.souza@intel.com

Valid, ranks and bandwidth_kbps are set into dram_info but are not
used anywhere else so nuking it.

Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210128164312.91160-1-jose.souza@intel.com

Atm the driver will calculate a wrong MST timeslots/MTP (aka time unit)
value for MST streams if the link parameters (link rate or lane count)
are limited in a way independent of the sink capabilities (reported by
DPCD).

One example of such a limitation is when a MUX between the sink and
source connects only a limited number of lanes to the display and
connects the rest of the lanes to other peripherals (USB).

Another issue is that atm MST core calculates the divider based on the
backwards compatible DPCD (at address 0x0000) vs. the extended
capability info (at address 0x2200). This can result in leaving some
part of the MST BW unused (For instance in case of the WD19TB dock).

Fix the above two issues by calculating the PBN divider value based on
the rate and lane count link parameters that the driver uses for all
other computation.

Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/2977


Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjala <ville.syrjala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125173636.1733812-2-imre.deak@intel.com

This function will be needed by the next patch where the driver
calculates the BW based on driver specific parameters, so export it.

At the same time sanitize the function params, passing the more natural
link rate instead of the encoding of the same rate.

v2:
- Fix function documentation. (Lyude)

Cc: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjala <ville.syrjala@intel.com>
Cc: <stable@vger.kernel.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210125173636.1733812-1-imre.deak@intel.com

The HDCP 1.4 spec does not require the QUERY_STREAM_ENCRYPTION_STATUS
check, it was always a nice-to-have. After deploying this across various
devices, we've determined that some MST bridge chips do not properly
support this call for HDCP 1.4 (namely Synaptics and Realtek).

I had considered creating a quirk for this, but I think it's more
prudent to just disable the check entirely since I don't have an idea
how widespread support is.

Changes in v2:
-Rebased on -tip

Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210106223909.34476-1-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20210121172620.33066-1-sean@poorly.run

Prevent the ICL HDR plane pipeline from performing YUV color range
correction twice when the input is in limited range. This is done by
removing the limited-range code from icl_program_input_csc().

Before this patch the following could happen: user space gives us a YUV
buffer in limited range; per the pipeline in [1], the plane would first
go through a "YUV Range correct" stage that expands the range; the plane
would then go through the "Input CSC" stage which would also expand the
range because icl_program_input_csc() would use a matrix and an offset
that assume limited-range input; this would ultimately cause dark and
light colors to appear darker and lighter than they should respectively.

This is an issue because if a buffer switches between being scanned out
and being composited with the GPU, the user will see a color difference.
If this switching happens quickly and frequently, the user will perceive
this as a flickering.

[1] https://01.org/sites/default/files/documentation/intel-gfx-prm-osrc-icllp-vol12-displayengine_0.pdf#page=281



Cc: stable@vger.kernel.org
Signed-off-by: Andres Calderon Jaramillo <andrescj@chromium.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215224219.3896256-1-andrescj@google.com

Inform us if we're buggy and are about to exceed the size of the
bitfields in the plane TILEOFF/OFFSET registers.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111163711.12913-2-ville.syrjala@linux.intel.com


Reviewed-by: Karthik B S <karthik.b.s@intel.com>

DSI transcoder does not support VRR and hence skip the HW state
readout if its a DSI transcoder.

Fixes: c7f0f437

 ("drm/i915/display: Add HW state readout for VRR")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210126185224.32340-1-manasi.d.navare@intel.com

Readout the dbuf related stuff during driver init/resume and
stick it into our dbuf state.

v2: Keep crtc_state->wm.skl.ddb

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-9-ville.syrjala@linux.intel.com

In order to make the dbuf state computation less fragile
let's make it stand on its own feet by not requiring someone
to peek into a crystall ball ahead of time to figure out
which pipes need to be added to the state under which potential
future conditions. Instead we compute each piece of the state
as we go along, and if any fallout occurs that affects more than
the current set of pipes we add the affected pipes to the state
naturally.

That requires that we track a few extra thigns in the global
dbuf state: dbuf slices for each pipe, and the weight each
pipe has when distributing the same set of slice(s) between
multiple pipes. Easy enough.

We do need to follow a somewhat careful sequence of computations
though as there are several steps involved in cooking up the dbuf
state. Thoguh we could avoid some of that by computing more things
on demand instead of relying on earlier step of the algorithm to
have filled it out. I think the end result is still reasonable
as the entire sequence is pretty much consolidated into a single
function instead of being spread around all over.

The rough sequence is this:
1. calculate active_pipes
2. calculate dbuf slices for every pipe
3. calculate total enabled slices
4. calculate new dbuf weights for any crtc in the state
5. calculate new ddb entry for every pipe based on the sets of
   slices and weights, and add any affected crtc to the state
6. calculate new plane ddb entries for all crtcs in the state,
   and add any affected plane to the state so that we'll perform
   the requisite hw reprogramming

And as a nice bonus we get to throw dev_priv->wm.distrust_bios_wm
out the window.

v2: Keep crtc_state->wm.skl.ddb

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-8-ville.syrjala@linux.intel.com

Extract the code to calculate the weights used to chunk up the dbuf
between pipes. There's still extra stuff in there that shouldn't be
there and must be moved out, but that requires a bit more state to
be tracked in the dbuf state.

v2: Keep crtc_state->wm.skl.ddb

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-7-ville.syrjala@linux.intel.com

The dbuf state will be where we collect all the inter-pipe dbuf
allocation stuff. Start by adding the actual per-pipe ddb entries
there.

Originally the plan was to move them there outright, but that no longer
works as we're no longer guaranteed to have a dbuf state when it comes
time to sanity check the ddb overlaps in skl_commit_modeset_enables().
I think when I wrote this originally we did the watermark/ddb
calculation last, and so we couldn't have any crtcs in the state w/o
also having the dbuf state. But that has since changed and we do the
watermark/ddb calculation much earlier, and thus it is now possible
to commit crtcs w/o a dbuf state. So we keep another copy of the
information in the crtc state.

v2: Rebase
v3: Duplicate the entries instead of moving

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-6-ville.syrjala@linux.intel.com

Generalize icl_get_first_dbuf_slice_offset() into something that
just gives us the start+end of the dbuf chunk covered by the
specified slices as a standard ddb entry. Initial idea was to use
it during readout as well, but we shall see.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-5-ville.syrjala@linux.intel.com

Put the code into a function with a descriptive name. Also relocate
the code a bit help future work.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-4-ville.syrjala@linux.intel.com

skl_compute_dbuf_slices() has no use for the crtc state, so
just pass the crtc itself.

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-3-ville.syrjala@linux.intel.com

skl_ddb_get_pipe_allocation_limits() doesn't care how the weights
for distributing the ddb are caclculated for each pipe. Put that
calculation into a separate function so that such mundane details
are hidden from view.

v2: s/adjusted_mode/pipe_mode/

Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122205633.18492-2-ville.syrjala@linux.intel.com

With vrr enabled the hardware no longer latches the registers
automagically at vblank start. The point at which it will do the
latching even when no push has been sent is the vmax decision
boundary. That is the thing we need to evade to avoid our
register latching to get split between two frames.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-18-manasi.d.navare@intel.com

To get sensible vblank timestamping behaviour we need to feed
the vmax based timings to the vblank code, otherwise it'll chop
off the scanline counter when it exceeds the minumum vtotal.

Additionally with VRR we have three cases to consider when we
generate the vblank timestamp:
1) we are in vertical active
  -> nothing special needs to be done, just return the current
     scanout position and the core will calculate the timestamp
     corresponding to the past time when the current vertical
     active started
2) we are in vertical blank and no push has been sent
  -> the hardware will keep extending the vblank presumably
     to its maximum length, so we make the timestmap match the
     expected time when the max length vblank will end. Since
     the timings used for this are now based on vmax nothing
     special actually needs to be done
3) we are in vblank and a push has been sent so the vblank is
   about to terminate
  -> presumably we want the timestmap to accurately reflect
     when the vblank will terminate, so we use the sampled
     frame timestamp vs. current timestamp to guesstimate
     how far along the vblank exit we are, and then we
     adjust the reported scanout position accordingly so
     that the core will see that the vblank is close to
     ending.

v2:
* Fix the else if (use_scanline_Counter) (Manasi)

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-17-manasi.d.navare@intel.com

Dump vrr state alongside everything else.

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-16-manasi.d.navare@intel.com

With VRR the earliest the registers can get latched are at
flipline decision boundary, calculate that as vrr_vmin_vblank_start()
and the latest the regsiters can get latched are vmax decision boundary
calculate that as vrr_vmax_vblank_start()

v2:
* Remove TODO and adjust extra scanline const (Manasi)

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-15-manasi.d.navare@intel.com

This functions gets the VRR config from the VRR registers
to match the crtc state variables for VRR.

v2:
* Rebase (Manasi)
* Use HAS_VRR (Jani N)

v3:
* Get pipeline_full, flipline (Ville)

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-14-manasi.d.navare@intel.com

If VRR is enabled, the sink should ignore MSA parameters
and regenerate incoming video stream without depending
on these parameters. Hence set the MSA_TIMING_PAR_IGNORE_EN
bit if VRR is enabled.
Reset this bit on VRR disable.

v2:
* ACtually set the dpcd msa ignore bit (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-13-manasi.d.navare@intel.com

This patch disables the VRR enable and VRR PUSH
bits in the HW during commit modeset disable sequence.

Thsi disable will happen when the port is disabled
or when the userspace sets VRR prop to false and
requests to disable VRR.

v2:
* Use intel_de_rmw (Jani N)

v3:
* Remove rmw (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-12-manasi.d.navare@intel.com

VRR achieves vblank stretching using the HW PUSH functionality.
So once the VRR is enabled during modeset then for each flip
request from userspace, in the atomic tail pipe_update_end()
we need to set the VRR push bit in HW for it to terminate
the vblank at configured flipline or anytime after flipline
or latest at the Vmax.

The HW clears the PUSH bit after the double buffer updates
are completed.

v2:
* Move send push to after irq en (Manasi)
* Call send push unconditionally (Jani N)

v3:
* Stall w.r.t Vrr vmax (Manasi, Gary Smith)

v4:
* Remove the rmw (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gary Smith <gary.k.smith@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-11-manasi.d.navare@intel.com

This patch computes the VRR parameters from VRR crtc states
and configures them in VRR registers during CRTC enable in
the modeset enable sequence.

v2:
* Remove initialization to 0 (Jani N)
* Use correct pipe %c (Jani N)

v3:
* Remove debug prints (Ville)
* Use cpu_trans instead of pipe for TRANS_VRR regs (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-10-manasi.d.navare@intel.com

Give the pipeline full line count bits more descriptive names

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-9-manasi.d.navare@intel.com

If VRR is enabled, DRRS cannot be enabled, so make this check
in atomic check.

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-8-manasi.d.navare@intel.com

Even though our HW supports PSR + VRR, the available panels
do not work reliably with PSR and VRR together. So if user
requested VRR and is supported by HW enable that and do not
enable PSR in that case.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-7-manasi.d.navare@intel.com

This forces a complete modeset if vrr drm crtc state goes
from enabled to disabled and vice versa.
This patch also computes vrr state variables from the mode timings
and based on the vrr property set by userspace as well as hardware's
vrr capability.

v2:
*Rebase
v3:
* Vmin = max (vtotal, vmin) (Manasi)
v4:
* set crtc_state->vrr.enable = 0 for disable request
v5:
* drm_dbg_kms, squash crtc states def patch (Jani N)
v6:
* Move vrr modeset check to separate function (Jani N)
v7:
* Ville's fixes - vmin, vmax rename, fix rounding dir
* Add pipeline full, flipline to crtc state
* Pass conn state to vrr_compute_config (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-6-manasi.d.navare@intel.com

Extract intel_crtc_scanlines_since_frame_timestamp() from
__intel_get_crtc_scanline_from_timestamp(). We'll reuse this
for VRR vblank timestamps.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-5-manasi.d.navare@intel.com

We want to calculate the vblank_start for vblank evasion
differently for vrr. To make that nicer lets first extract
the current non-vrr case to a helper.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-4-manasi.d.navare@intel.com

The vrr calculations will need to know the framestart delay value
we use. Currently we program it always to zero, but should that change
we probably want to stash it somewhere.

Could stick it into the crtc_state I suppose, but since we never
change it let's just stuff it into dev_priv for now.

v2:
* Rebase on drm-tip (Manasi)

v3:
* Framestart_delay as 1 - 4 to align with HW

Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210122232647.22688-3-manasi.d.navare@intel.com