Commit 915fbe59

 ("ARM: dts: imx: Add missing #phy-cells to
usb-nop-xceiv") missed to update imx51-zii-rdu1.dts probably due to a
merge timing issue, so add #phy-cells here too.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the leading zero from unit address to fix the following build
warning with W=1:

arch/arm/boot/dts/imx6dl-hummingboard2.dtb: Warning (unit_address_format): Node /soc/aips-bus@2100000/i2c@21a0000/codec@0a unit name should not have leading 0s

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Moxa UC-8410A open platform

The UC-8410A computing platform is designed
for embedded communication-centric industrial applications

The features of UC-8410A are:
* QSPI flash
* SD slot
* 3x LAN
* 8x RS-232/422/485 ports, software-selectable
* Mini PCIe form factor with PCIe/USB signal
* 2x USB host
* TPM
* Watchdog
* RTC
* User LEDs
* Beeper
* Push button

Signed-off-by: Jimmy Chen <jimmy.chen@moxa.com>
Signed-off-by: Harry YJ Jhou <harryyj.jhou@moxa.com>
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

On imx51-babbage there is a 26MHz oscillator that is gated by GPIO3_1.

The output of this clock feeds audio codec clock and USB PHY clocks,
which are gated by GPIO4_26 and GPIO2_1 respectively.

Fix the clock representation by properly using gpio-gate-clock.

The clock nodes can be moved out of the 'clocks' node.

Based on a commit from Lucas Stach for imx51-zii-rdu1 board.

This also fixes the following build warning with W=1:

arch/arm/boot/dts/imx51-babbage.dtb: Warning (unit_address_vs_reg): Node /clocks/codec_clock has a reg or ranges property, but no unit name

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Switch 2 has an 88e1545 PHY behind it, which is a quad PHY.  Only the
first three PHYs are used, the remaining PHY is unused.  When we wire
up the SFF sockets in a later commit, the omission of this causes the
fourth PHY to be used for port 3.  Specifying the PHYs in DT avoids
the auto-probing of the bus, and discovery of this PHY.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The interrupt specification for the GPIO expander is wrong - the
expander is wired to PTB28, which is GPIO98.  GPIO98 is on gpio chip
3, not 2.

In addition, the device is missing a required property.  Interrupt
controllers must have the "interrupt-controller" property specified.
Add this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

EDMA1 is required for the SPI controller used on the ZII boards to be
functional.  Enable EDMA1.

Fixes: 14c41633

 ("ARM: dts: vfxxx: Enable DMA for DSPI on Vybrid")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is an extraneous '1' cell in the clock phandle, which causes
the following build warning:

arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])

Remove the unneeded extra cell.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

There is an extraneous '1' cell in the clock phandle, which causes
the following build warning:

arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])

Remove the unneeded extra cell.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

rtc-mxc_v2 driver will add support for the i.MX53 SRTC

Note: we keep the 'srtc' label to avoid duplicate with imx53-m53.dtsi

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

In the provided example the unit address does not match the 'reg' value,
as IMX7_POWER_DOMAIN_PCIE_PHY is defined as 1.

Fix the unit address and avoid using defines in reg as per Rob
Herring's recommendation.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Improve the DTS files using lower case to fix the following dtc warnings:

Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"

Converted using the following command:

find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C

For simplicity, two sed expressions were used to solve each warnings separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This is a follow up to commit 4c9847b7

 ("dt-bindings: Remove leading 0x from bindings notation")

Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The uSDHC controller directly provides a VSELECT signal that can be
muxed to the external voltage select. Mux the VSELECT directly to avoid
using a GPIO.

Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Previously PCI support was working because the bootloader has previously
powered up the PCI power domain.

Represent the PCI power domain, so that PCI is functional without
relying on the PCI support from the bootloader.

Tested on a imx6sx-sdb board with no PCI support in the bootloader.

Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The third cell of the PCI non-prefetchable memory range should be
0x08000000, so change it accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make the regulators match the schematic - name the regulators after
one of their schematic supply names, and arrange them into their
heirarchy.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the v1.5 SOM with TI Wi-Fi and eMMC.  As the pinmux
settings are different for the microsom, we need to use a separate
board-level dts for this as there is no support for overlays.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the v1.5 SOM with TI Wi-Fi but without eMMC.  As the
pinmux settings are different for the microsom, we need to use a
separate board-level dts for this as there is no support for overlays.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

eMMC is optional on HB2 boards, and may be implemented by the SOM.  Move
it out of the base HB2 include file.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Name the regulators according to the voltage rails they are feeding in
the schematic. The USB 2-4 regulators are fixed regulators and are always
on, as they are not a VBUS supply for a single USB host port on the i.MX6,
but supply VBUS to ports behind a USB hub and there is currently no way
to model this in mainline.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The PWM nodes are already disabled in the imx6qdl.dtsi, so there
is no need to disable them again in the board DTS.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The driver always uses active-low, but better describe reality in the DT.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It's disabled by default and the data mapping is supposed to be
retrieved from the attached panel driver in mainline.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

VDDD is supplied by VCC_1P8 on HB2.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Trivial formatting change.

Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Use proper gpio flag definitions for GPIOs rather than using opaque
uninformative numbers.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Fix the SD card detect signal, which was missing the polarity
specification, and the pull-up necessary for proper signalling.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Broadcom Wi-Fi was moved out to a separate include file.  Add the
include.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Move the microsom includes into the .dts files.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Rename microsom include to imx6qdl-sr-som.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Remove the AR8035 include, the file is now gone.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds support for the Hummingboard Gate and Edge devices from
SolidRun.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These device trees add support for the TS-4600 by Technologic Systems.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4600



Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the documentation for the TS-4600 by Technologic Systems.

Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

These device trees add support for TS-7970 by Technologic Systems.

More details here:
   https://wiki.embeddedarm.com/wiki/TS-7970



Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This adds the documentation for the TS-7970 by Technologic Systems.

Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for the Computer on Module Colibri iMX7D 1GB along
with the Colibri Evaluation Board device trees. Follow the usual
hierarchic include model, maintaining shared configuration in
imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>