As per internal decision, Joao Pinto will be maintainer for DWC UFS
driver.

Signed-off-by: Prabu Thangamuthu <prabut@synopsys.com>
Acked-by: Joao Pinto <Joao.Pinto@synopsys.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

gcc points out a theorerical string overflow:

drivers/message/fusion/mptbase.c: In function 'mpt_detach':
drivers/message/fusion/mptbase.c:2103:17: error: '%s' directive writing up to 31 bytes into a region of size 28 [-Werror=format-overflow=]
sprintf(pname, MPT_PROCFS_MPTBASEDIR "/%s/summary", ioc->name);
               ^~~~~
drivers/message/fusion/mptbase.c:2103:2: note: 'sprintf' output between 13 and 44 bytes into a destination of size 32

We can simply double the size of the local buffer here to be on the
safe side, and using snprintf() instead of sprintf() protects us
if ioc->name was not terminated properly.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We print a 256 byte event string into a buffer that is only 161
bytes long, this is clearly wrong:

drivers/scsi/gdth_proc.c: In function 'gdth_show_info':
drivers/scsi/gdth.c:3660:41: error: '%s' directive writing up to 255 bytes into a region of size between 141 and 150 [-Werror=format-overflow=]
             sprintf(buffer,"Adapter %d: %s\n",
                                         ^~
/git/arm-soc/drivers/scsi/gdth.c:3660:13: note: 'sprintf' output between 13 and 277 bytes into a destination of size 161
             sprintf(buffer,"Adapter %d: %s\n",
             ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
                 dvr->eu.async.ionode,dvr->event_string);
                 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

gcc calculates that the worst case buffer size would be 277 bytes,
so we can use that.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The MSI interrupt name can require 11 bytes in addition to the device name,
for a total of 23 bytes:

drivers/scsi/fnic/fnic_isr.c: In function 'fnic_request_intr':
drivers/scsi/fnic/fnic_isr.c:192:4: error: '-fcs-rq' directive writing 7 bytes into a region of size between 5 and 16 [-Werror=format-overflow=]
    "%.11s-fcs-rq", fnic->name);
drivers/scsi/fnic/fnic_isr.c:206:3: note: 'sprintf' output between 12 and 23 bytes into a destination of size 16
   sprintf(fnic->msix[FNIC_MSIX_ERR_NOTIFY].devname,
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    "%.11s-err-notify", fnic->name);

This extends the buffer to fit any possible value.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

gcc notices that we would overflow the buffer for the
inquiry of the product name if we have too many adapters:

drivers/scsi/gdth.c: In function 'gdth_next':
drivers/scsi/gdth.c:2357:29: warning: 'sprintf' may write a terminating nul past the end of the destination [-Wformat-overflow=]
         sprintf(inq.product,"Host Drive  #%02d",t);
                             ^~~~~~~~~~~~~~~~~~~
drivers/scsi/gdth.c:2357:9: note: 'sprintf' output between 16 and 17 bytes into a destination of size 16
         sprintf(inq.product,"Host Drive  #%02d",t);

This won't happen in practice, so just use snprintf to
truncate the string.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

We print the driver name into one string and then add and ID
and copy it into a second string of the same length, at which
point gcc complains about a possible overflow:

drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function '_scsih_probe':
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: error: '_cm' directive writing 3 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
printf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id);
                  ^~~~~~~~~
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:21: note: directive argument in the range [0, 255]
drivers/scsi/mpt3sas/mpt3sas_scsih.c:8884:2: note: 'sprintf' output between 5 and 38 bytes into a destination of size 32
  sprintf(ioc->name, "%s_cm%d", ioc->driver_name, ioc->id);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Making the first string shorter is sufficient to avoid the
warning here, as we know it can only contain either "mpt2sas"
or "mpt3sas".

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

gcc-7 complains that the firmware version strings might overflow
for some values:

drivers/scsi/megaraid.c: In function 'megaraid_probe_one':
drivers/scsi/megaraid.c:314:33: error: '%d' directive writing between 1 and 2 bytes into a region of size between 1 and 2 [-Werror=format-overflow=]
drivers/scsi/megaraid.c:314:33: note: directive argument in the range [0, 15]
drivers/scsi/megaraid.c:314:3: note: 'sprintf' output between 7 and 9 bytes into a destination of size 7
drivers/scsi/megaraid.c:320:35: error: '%d' directive writing between 1 and 2 bytes into a region of size between 1 and 2 [-Werror=format-overflow=]
drivers/scsi/megaraid.c:320:35: note: directive argument in the range [0, 15]
drivers/scsi/megaraid.c:320:3: note: 'sprintf' output between 7 and 9 bytes into a destination of size 7

This makes the code use a truncating snprintf() instead, which shuts
up that warning.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
some comments, accordingly.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API. It also updates
the name of some variables and the content of comments, accordingly.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The PCI pool API is deprecated. This commit replaces the PCI pool old
API by the appropriate function with the DMA pool API.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Peter Senna Tschudin <peter.senna@collabora.com>
Tested-by: Peter Senna Tschudin <peter.senna@collabora.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Limit PDMA send to 512 B to avoid data corruption on DTC3181E. The
corruption is always the same: one byte missing at the beginning of a
128 B block. It happens only with slow Quantum LPS 240 drive, not with
faster IBM DORS-32160. It's not clear what causes this. Documentation
for the DTC436 chip has not been made available.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The polling loops in pread() and pwrite() can easily become infinite
loops and hang the machine.

Merge the IRQ check into host buffer wait loop and add polling limit.

Also place a limit on polling for 53C80 registers accessibility.

[Use NCR5380_poll_politely2() for register polling. Rely on polling for
gated IRQ rather than polling for phase error, like the algorithm in the
53c400 datasheet. Move DTC436 workarounds into a separate patch.
Factor-out common code as wait_for_53c80_access(). Rework the residual
calculations. -- F.T.]

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The word "read" may be used to mean "DMA read operation" or "SCSI READ
command", though a READ command implies writing to memory.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When an IRQ arrives during PDMA transfer, pread() and pwrite() return
without waiting for the 53C80 registers to be ready and this ends up
messing up the chip state. This was observed with SONY CDU-55S which is
slow enough to disconnect during 4096-byte reads.

IRQ during PDMA is not an error so don't return -1. Instead, store the
remaining byte count for use by NCR5380_dma_residual().

[Poll for the BASR_END_DMA_TRANSFER condition rather than remove the
error message -- F.T.]

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

generic_NCR5380_dma_xfer_len() incorrectly uses cmd->transfersize which
causes rescan-scsi-bus and CD-ROM access to hang the system.  Use
cmd->SCp.this_residual instead, like other NCR5380 drivers.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When issuing a bus reset we should complete all commands, not
just the command triggering the reset.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

To correctly identify which fib has a scsi command callback this
patch implements a flag FIB_CONTEXT_FLAG_SCSI_CMD.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

aac_hba_send() will return FAILED for any non-SCSI command requests,
failing any TMFs. This patch updates the check to allow TMFs.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When sending a reset fib we shouldn't rely on the scsi command,
but rather set the TMF status in the map_info->reset_state variable.
That allows us to send a TMF independent on a scsi command.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Split off device, target, and bus reset functionality into
individual functions.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Split off the host reset parts of aac_eh_reset() into a separate
host reset function.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Split off reset FIB generation into separate functions.

Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull x86 platform driver fix from Darren Hart:
 "Fix loop preventing some platforms from waking up via the power button
  in s2idle:

   - intel-vbtn: match power button on press rather than release"

* tag 'platform-drivers-x86-v4.13-4' of git://git.infradead.org/linux-platform-drivers-x86:
  platform/x86: intel-vbtn: match power button on press rather than release

Pull ext4 fixes from Ted Ts'o:
 "A large number of ext4 bug fixes and cleanups for v4.13"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix copy paste error in ext4_swap_extents()
  ext4: fix overflow caused by missing cast in ext4_resize_fs()
  ext4, project: expand inode extra size if possible
  ext4: cleanup ext4_expand_extra_isize_ea()
  ext4: restructure ext4_expand_extra_isize
  ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
  ext4: make xattr inode reads faster
  ext4: inplace xattr block update fails to deduplicate blocks
  ext4: remove unused mode parameter
  ext4: fix warning about stack corruption
  ext4: fix dir_nlink behaviour
  ext4: silence array overflow warning
  ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
  ext4: release discard bio after sending discard commands
  ext4: convert swap_inode_data() over to use swap() on most of the fields
  ext4: error should be cleared if ea_inode isn't added to the cache
  ext4: Don't clear SGID when inheriting ACLs
  ext4: preserve i_mode if __ext4_set_acl() fails
  ext4: remove unused metadata accounting variables
  ext4: correct comment references to ext4_ext_direct_IO()

Pull MIPS fixes from Ralf Baechle:
 "This fixes two build issues for ralink platforms, both due to missing
  #includes which used to be included indirectly via other headers"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: mt7620: Add missing header
  MIPS: ralink: Fix build error due to missing header

The latest change of compat_sys_sigpending in commit 8f13621a


("sigpending(): move compat to native") has broken it in two ways.

First, it tries to write 4 bytes more than userspace expects:
sizeof(old_sigset_t) == sizeof(long) == 8 instead of
sizeof(compat_old_sigset_t) == sizeof(u32) == 4.

Second, on big endian architectures these bytes are being written in the
wrong order.

This bug was found by strace test suite.

Reported-by: Anatoly Pugachev <matorola@gmail.com>
Inspired-by: Eugene Syromyatnikov <evgsyr@gmail.com>
Fixes: 8f13621a

 ("sigpending(): move compat to native")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This bug was found by a static code checker tool for copy paste
problems.

Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

On a 32-bit platform, the value of n_blcoks_count may be wrong during
the file system is resized to size larger than 2^32 blocks.  This may
caused the superblock being corrupted with zero blocks count.

Fixes: 1c6bd717


Signed-off-by: Jerry Lee <jerrylee@qnap.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # 3.7+

When upgrading from old format, try to set project id
to old file first time, it will return EOVERFLOW, but if
that file is dirtied(touch etc), changing project id will
be allowed, this might be confusing for users, we could
try to expand @i_extra_isize here too.

Reported-by: Zhang Yi <yi.zhang@huawei.com>
Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Wang Shilong <wshilong@ddn.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Clean up some goto statement, make ext4_expand_extra_isize_ea() clearer.

Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>

Current ext4_expand_extra_isize just tries to expand extra isize, if
someone is holding xattr lock or some check fails, it will give up.
So rename its name to ext4_try_to_expand_extra_isize.

Besides that, we clean up unnecessary check and move some relative checks
into it.

Signed-off-by: Miao Xie <miaoxie@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Wang Shilong <wshilong@ddn.com>

We should avoid the contention between the i_extra_isize update and
the inline data insertion, so move the xattr trylock in front of
i_extra_isize update.

Signed-off-by: Miao Xie <miaoxie@huawei.com>
Reviewed-by: Wang Shilong <wshilong@ddn.com>

ext4_xattr_inode_read() currently reads each block sequentially while
waiting for io operation to complete before moving on to the next
block. This prevents request merging in block layer.

Add a ext4_bread_batch() function that starts reads for all blocks
then optionally waits for them to complete. A similar logic is used
in ext4_find_entry(), so update that code to use the new function.

Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

When an xattr block has a single reference, block is updated inplace
and it is reinserted to the cache. Later, a cache lookup is performed
to see whether an existing block has the same contents. This cache
lookup will most of the time return the just inserted entry so
deduplication is not achieved.

Running the following test script will produce two xattr blocks which
can be observed in "File ACL: " line of debugfs output:

  mke2fs -b 1024 -I 128 -F -O extent /dev/sdb 1G
  mount /dev/sdb /mnt/sdb

  touch /mnt/sdb/{x,y}

  setfattr -n user.1 -v aaa /mnt/sdb/x
  setfattr -n user.2 -v bbb /mnt/sdb/x

  setfattr -n user.1 -v aaa /mnt/sdb/y
  setfattr -n user.2 -v bbb /mnt/sdb/y

  debugfs -R 'stat x' /dev/sdb | cat
  debugfs -R 'stat y' /dev/sdb | cat

This patch defers the reinsertion to the cache so that we can locate
other blocks with the same contents.

Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>