Since 1599069a ("phy: core: Warn when phy_power_on is called before
phy_init") the driver complains. In my case (Amlogic SoC) the warning
is: phy phy-fe03e000.phy.2: phy_power_on was called before phy_init
So change the order of the two calls. The same change has to be done
to the order of phy_exit() and phy_power_off().

Fixes: 09a75e85

 ("usb: dwc2: refactor common low-level hw code to platform.c")
Cc: stable@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/dfcc6b40-2274-4e86-e73c-5c5e6aa3e046@gmail.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For ARM processor, unaligned access to device memory is not allowed.
Method memcpy does not take care of alignment.

USB detection failure with the unaligned address of memory access, with
below kernel crash. To fix the unaligned address the kernel panic issue,
replace memcpy with memcpy_toio method.

Kernel crash:
Unable to handle kernel paging request at virtual address ffff80000c05008a
Mem abort info:
  ESR = 0x96000061
  EC = 0x25: DABT (current EL), IL = 32 bits
  SET = 0, FnV = 0
  EA = 0, S1PTW = 0
  FSC = 0x21: alignment fault
Data abort info:
  ISV = 0, ISS = 0x00000061
  CM = 0, WnR = 1
swapper pgtable: 4k pages, 48-bit VAs, pgdp=000000000143b000
[ffff80000c05008a] pgd=100000087ffff003, p4d=100000087ffff003,
pud=100000087fffe003, pmd=1000000800bcc003, pte=00680000a0010713
Internal error: Oops: 96000061 [#1] SMP
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.15.19-xilinx-v2022.1 #1
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
pstate: 200000c5 (nzCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __memcpy+0x30/0x260
lr : __xudc_ep0_queue+0xf0/0x110
sp : ffff800008003d00
x29: ffff800008003d00 x28: ffff800009474e80 x27: 00000000000000a0
x26: 0000000000000100 x25: 0000000000000012 x24: ffff000800bc8080
x23: 0000000000000001 x22: 0000000000000012 x21: ffff000800bc8080
x20: 0000000000000012 x19: ffff000800bc8080 x18: 0000000000000000
x17: ffff800876482000 x16: ffff800008004000 x15: 0000000000004000
x14: 00001f09785d0400 x13: 0103020101005567 x12: 0781400000000200
x11: 00000000c5672a10 x10: 00000000000008d0 x9 : ffff800009463cf0
x8 : ffff8000094757b0 x7 : 0201010055670781 x6 : 4000000002000112
x5 : ffff80000c05009a x4 : ffff000800a15012 x3 : ffff00080362ad80
x2 : 0000000000000012 x1 : ffff000800a15000 x0 : ffff80000c050088
Call trace:
 __memcpy+0x30/0x260
 xudc_ep0_queue+0x3c/0x60
 usb_ep_queue+0x38/0x44
 composite_ep0_queue.constprop.0+0x2c/0xc0
 composite_setup+0x8d0/0x185c
 configfs_composite_setup+0x74/0xb0
 xudc_irq+0x570/0xa40
 __handle_irq_event_percpu+0x58/0x170
 handle_irq_event+0x60/0x120
 handle_fasteoi_irq+0xc0/0x220
 handle_domain_irq+0x60/0x90
 gic_handle_irq+0x74/0xa0
 call_on_irq_stack+0x2c/0x60
 do_interrupt_handler+0x54/0x60
 el1_interrupt+0x30/0x50
 el1h_64_irq_handler+0x18/0x24
 el1h_64_irq+0x78/0x7c
 arch_cpu_idle+0x18/0x2c
 do_idle+0xdc/0x15c
 cpu_startup_entry+0x28/0x60
 rest_init+0xc8/0xe0
 arch_call_rest_init+0x10/0x1c
 start_kernel+0x694/0x6d4
 __primary_switched+0xa4/0xac

Fixes: 1f7c5166

 ("usb: gadget: Add xilinx usb2 device support")
Cc: stable@vger.kernel.org
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Link: https://lore.kernel.org/r/20220824071253.1261096-1-piyush.mehta@amd.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Retimer device class is left dangling when the typec module
is unloaded. Attempts to reload the module failed with warning:

        "sysfs: cannot create duplicate filename '/class/retimer'"

Fixing the issue by unregistering the class properly.

Fixes: ddaf8d96

 ("usb: typec: Add support for retimers")
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220825140411.10743-1-heikki.krogerus@linux.intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dwc3 driver manages its PHYs itself so the USB core PHY management
needs to be disabled.

Use the struct xhci_plat_priv hack added by commits 46034a99 ("usb:
host: xhci-plat: add platform data support") and f768e718 ("usb:
host: xhci-plat: add priv quirk for skip PHY initialization") to
propagate the setting for now.

Fixes: 4e88d4c0 ("usb: add a flag to skip PHY initialization to struct usb_hcd")
Fixes: 178a0bce

 ("usb: core: hcd: integrate the PHY wrapper into the HCD core")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Cc: stable <stable@kernel.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220825131836.19769-1-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Lenovo OneLink+ Dock contains two VL812 USB3.0 controllers:
17ef:1018 upstream
17ef:1019 downstream

Those two controllers both have problems with some USB3.0 devices,
particularly self-powered ones. Typical error messages include:

  Timeout while waiting for setup device command
  device not accepting address X, error -62
  unable to enumerate USB device

By process of elimination the controllers themselves were identified as
the cause of the problem. Through trial and error the issue was solved
by using USB_QUIRK_RESET_RESUME for both chips.

Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220824191320.17883-1-jflf_kernel@gmx.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit 83810f84.

Turning off port power in shutdown did cause issues such as a laptop not
proprly powering off, and some specific usb devies failing to enumerate the
subsequent boot after a warm reset.

So revert this.

Fixes: 83810f84

 ("xhci: turn off port power in shutdown")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-4-mathias.nyman@linux.intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After xHC controller is started, either in probe or resume, it can take
a while before any of the connected usb devices are visible to the roothub
due to link training.

It's possible xhci driver loads, sees no acivity and suspends the host
before the USB device is visible.

In one testcase with a hotplugged xHC controller the host finally detected
the connected USB device and generated a wake 500ms after host initial
start.

If hosts didn't suspend the device duringe training it probablty wouldn't
take up to 500ms to detect it, but looking at specs reveal USB3 link
training has a couple long timeout values, such as 120ms
RxDetectQuietTimeout, and 360ms PollingLFPSTimeout.

So Add a 500ms grace period that keeps polling the roothub for 500ms after
start, preventing runtime suspend until USB devices are detected.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-3-mathias.nyman@linux.intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The remove path in xhci platform driver tries to remove and put both main
and shared hcds even if only a main hcd exists (one roothub)

This causes a null pointer dereference in reboot for those controllers.

Check that the shared_hcd exists before trying to remove it.

Fixes: e0fe9869

 ("usb: host: xhci-plat: prepare operation w/o shared hcd")
Reported-by: Alexey Sheplyakov <asheplyakov@basealt.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220825150840.132216-2-mathias.nyman@linux.intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The recent commit 87d0e2f4 ("usb: typec: ucsi: add a common
function ucsi_unregister_connectors()") introduced a regression that
caused NULL dereference at reading the power supply sysfs.  It's a
stale sysfs entry that should have been removed but remains with NULL
ops.  The commit changed the error handling to skip the entries after
a NULL con->wq, and this leaves the power device unreleased.

For addressing the regression, the straight revert is applied here.
Further code improvements can be done from the scratch again.

Link: https://bugzilla.suse.com/show_bug.cgi?id=1202386
Link: https://lore.kernel.org/r/87r11cmbx0.wl-tiwai@suse.de
Fixes: 87d0e2f4

 ("usb: typec: ucsi: add a common function ucsi_unregister_connectors()")
Cc: <stable@vger.kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20220823065455.32579-1-tiwai@suse.de


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The dwc3_qcom_read_usb2_speed() helper is now only called when the
controller is acting as host, but the compiler will warn that the hcd
variable is unused in gadget-only W=1 builds.

Fixes: c06795f1

 ("usb: dwc3: qcom: fix gadget-only builds")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220822100550.3039-1-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'thunderbolt-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-linus

Mika writes:
  "thunderbolt: Fixes for v6.0-rc3

  This includes two fixes: one that corrects the buffer usage in
  tb_async_error() and another one that limits the xHCI connect operations
  to Thunderbolt 3 routers.

  Both have been in linux-next with no reported issues."

* tag 'thunderbolt-for-v6.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
  thunderbolt: Check router generation before connecting xHCI
  thunderbolt: Use the actual buffer in tb_async_error()

Add a new compatible for mt8188

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220819081027.32382-1-chunfeng.yun@mediatek.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Supports for ICOM F3400 and ICOM F4400 PMR radios in CDC-ACM driver
enabling the AT serial port.
The Vendor Id is 0x0C26
The Product ID is 0x0020

Output of lsusb :
Bus 001 Device 009: ID 0c26:0020 Prolific Technology Inc. ICOM Radio
Couldn't open device, some information will be missing
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            2 Communications
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x0c26 Prolific Technology Inc.
  idProduct          0x0020
  bcdDevice            0.00
  iManufacturer           1 ICOM Inc.
  iProduct                2 ICOM Radio
  iSerial                 3 *obfuscated*
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength       0x0030
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xc0
      Self Powered
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         2 Communications
      bInterfaceSubClass      2 Abstract (modem)
      bInterfaceProtocol      1 AT-commands (v.25ter)
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x83  EP 3 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval              12
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass        10 CDC Data
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0

Signed-off-by: Thierry GUIBERT <thierry.guibert@croix-rouge.fr>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220819081702.84118-1-thierry.guibert@croix-rouge.fr


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On page 362 of the USB3.2 specification (
https://usb.org/sites/default/files/usb_32_20210125.zip),
The 'SuperSpeed Endpoint Companion Descriptor' shall only be returned
by Enhanced SuperSpeed devices that are operating at Gen X speed.
Each endpoint described in an interface is followed by a 'SuperSpeed
Endpoint Companion Descriptor'.

If users use SuperSpeed UDC, host can't recognize the device if endpoint
doesn't have 'SuperSpeed Endpoint Companion Descriptor' followed.

Currently in the uac2 driver code:
1. ss_epout_desc_comp follows ss_epout_desc;
2. ss_epin_fback_desc_comp follows ss_epin_fback_desc;
3. ss_epin_desc_comp follows ss_epin_desc;
4. Only ss_ep_int_desc endpoint doesn't have 'SuperSpeed Endpoint
Companion Descriptor' followed, so we should add it.

Fixes: eaf6cbe0

 ("usb: gadget: f_uac2: add volume and mute support")
Cc: stable <stable@kernel.org>
Signed-off-by: Jing Leng <jleng@ambarella.com>
Signed-off-by: Jack Pham <quic_jackp@quicinc.com>
Link: https://lore.kernel.org/r/20220721014815.14453-1-quic_jackp@quicinc.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This happens when @udev->reset_resume is set to true, when usb resume,
the flow as below:
  - hub_resume
    - usb_disable_interface
      - usb_disable_endpoint
        - usb_hcd_disable_endpoint
          - xhci_endpoint_disable  // it set @ep->hcpriv to NULL

Then when reset usb device, it will drop allocated endpoints,
the flow as below:
  - usb_reset_and_verify_device
    - usb_hcd_alloc_bandwidth
      - xhci_mtk_drop_ep

but @ep->hcpriv is already set to NULL, the bandwidth will be not
released anymore.

Due to the added endponts are stored in hash table, we can drop the check
of @ep->hcpriv.

Fixes: 4ce18666

 ("usb: xhci-mtk: Do not use xhci's virt_dev in drop_endpoint")
Cc: stable <stable@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20220819080556.32215-2-chunfeng.yun@mediatek.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently uses the worst case byte budgets on FS/LS bus bandwidth,
for example, for an isochronos IN endpoint with 192 bytes budget, it
will consume the whole 5 uframes(188 * 5) while the actual FS bus
budget should be just 192 bytes. It cause that many usb audio headsets
with 3 interfaces (audio input, audio output, and HID) cannot be
configured.
To improve it, changes to use "approximate" best case budget for FS/LS
bandwidth management. For the same endpoint from the above example,
the approximate best case budget is now reduced to (188 * 2) bytes.

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20220819080556.32215-1-chunfeng.yun@mediatek.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.

According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.

For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:

        dp->alt->vdo=0x140045

The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.

This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.

To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.

Fixes: 0e3bb7d6

 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

onboard_hub_power_off() currently has a delay after asserting the
reset of the hub. There is already a delay in onboard_hub_power_on()
before de-asserting the reset, which ensures that the reset is
asserted for the required time, so the delay in _power_off() is not
needed.

Skip the reset GPIO check before calling gpiod_set_value_cansleep(),
the function returns early when the GPIO descriptor is NULL.

Reviewed-By: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220805111836.1.Id5a4dc0a2c046236116693aa55672295513a0f2a@changeid


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Relocate the pullups_connected check until after it is ensured that there
are no runtime PM transitions.  If another context triggered the DWC3
core's runtime resume, it may have already enabled the Run/Stop.  Do not
re-run the entire pullup sequence again, as it may issue a core soft
reset while Run/Stop is already set.

This patch depends on
  commit 69e131d1 ("usb: dwc3: gadget: Prevent repeat pullup()")

Fixes: 77adb8bd

 ("usb: dwc3: gadget: Allow runtime suspend if UDC unbinded")
Cc: stable <stable@kernel.org>
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220728020647.9377-1-quic_wcheng@quicinc.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the necessary PCI device ID for the controller
inside the Intel Raptor Lake CPU block. The controllers that
are part of the PCH (chipset) have separate device IDs.

Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220815123334.87526-1-heikki.krogerus@linux.intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds the necessary ACPI ID for Intel Meteor Lake
IOM devices.

The callback function is_memory() is modified so that it
also checks if the resource descriptor passed to it is a
memory type "Address Space Resource Descriptor".

On Intel Meteor Lake the ACPI memory resource is not
described using the "32-bit Memory Range Descriptor" because
the memory is outside of the 32-bit address space. The
memory resource is described using the "Address Space
Resource Descriptor" instead.

Intel Meteor Lake is the first platform to describe the
memory resource for this device with Address Space Resource
Descriptor, but it most likely will not be the last.
Therefore the change to the is_memory() callback function
is made generic.

Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Cc: stable@vger.kernel.org
[ heikki: Rewrote the commit message. ]
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20220816101629.69054-2-heikki.krogerus@linux.intel.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a compatible for DWC3 found on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220716193257.456023-4-konrad.dybcio@somainline.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up the suspend callbacks by separating the error and success paths
to improve readability.

Also drop a related redundant initialisation.

Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-10-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is the Qualcomm glue wakeup interrupts that may be able to wake the
system from suspend and this can now be described in the devicetree.

Move the wakeup-source property handling over from the core driver and
instead propagate the capability setting to the core device during
probe.

This is needed as there is currently no way for the core driver to query
the wakeup setting of the glue device, but it is the core driver that
manages the PHY power state during suspend.

Also don't leave the PHYs enabled when system wakeup has been disabled
through sysfs.

Fixes: 649f5c84

 ("usb: dwc3: core: Host wake up support from system suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-9-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a wakeup-source property to the binding to describe whether the
wakeup interrupts can wake the system from suspend.

Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-8-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A recent commit implementing wakeup support in host mode instead broke
suspend for peripheral and OTG mode.

The hack that was added in the suspend path to determine the speed of
any device connected to the USB2 bus not only accesses internal driver
data for a child device, but also dereferences a NULL pointer or
accesses freed data when the controller is not acting as host.

There's no quick fix to the layering violation, but since reverting
would leave us with broken suspend in host mode with wakeup triggering
immediately, let's keep the hack for now.

Fix the immediate issues by only checking the host bus speed and
enabling wakeup interrupts when acting as host.

Fixes: 6895ea55

 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-7-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A device must enable wakeups during runtime suspend regardless of
whether it is capable and allowed to wake the system up from system
suspend.

Fixes: 2664deb0

 ("usb: dwc3: qcom: Honor wakeup enabled/disabled state")
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-6-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Qualcomm dwc3 runtime-PM implementation checks the xhci
platform-device pointer in the wakeup-interrupt handler to determine
whether the controller is in host mode and if so triggers a resume.

After a role switch in OTG mode the xhci platform-device would have been
freed and the next wakeup from runtime suspend would access the freed
memory.

Note that role switching is executed from a freezable workqueue, which
guarantees that the pointer is stable during suspend.

Also note that runtime PM has been broken since commit 2664deb0
("usb: dwc3: qcom: Honor wakeup enabled/disabled state"), which
incidentally also prevents this issue from being triggered.

Fixes: a4333c3a

 ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org      # 4.18
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-5-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A recent change added a dependency to the USB host stack and broke
gadget-only builds of the driver.

Fixes: 6895ea55

 ("usb: dwc3: qcom: Configure wakeup interrupts during suspend")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-4-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit d9be8d5c.

Generic power-domain flags must be set before the power-domain is
initialised and must specifically not be modified by drivers for devices
that happen to be in the domain.

To make sure that USB power-domains are left enabled during system
suspend when a device in the domain is in the wakeup path, the
GENPD_FLAG_ACTIVE_WAKEUP flag should instead be set for the domain
unconditionally when it is registered.

Note that this also avoids keeping power-domains on during suspend when
wakeup has not been enabled (e.g. through sysfs).

For the runtime PM case, making sure that the PHYs are not suspended and
that they are in the same domain as the controller prevents the domain
from being suspended. If there are cases where this is not possible or
desirable, the genpd implementation may need to be extended.

Fixes: d9be8d5c

 ("usb: dwc3: qcom: Keep power domain on to retain controller status")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-3-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Generic PHYs must be powered-off before they can be tore down.

Similarly, suspending legacy PHYs after having powered them off makes no
sense.

Fix the dwc3_core_exit() (e.g. called during suspend) and open-coded
dwc3_probe() error-path sequences that got this wrong.

Note that this makes dwc3_core_exit() match the dwc3_core_init() error
path with respect to powering off the PHYs.

Fixes: 03c1fd62 ("usb: dwc3: core: add phy cleanup for probe error handling")
Fixes: c499ff71

 ("usb: dwc3: core: re-factor init and exit paths")
Cc: stable@vger.kernel.org      # 4.8
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220804151001.23612-2-johan+linaro@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This is USB mass storage primary boot loader for code download on
NXP PN7462AU.

Without the quirk it is impossible to write whole memory at once as
device restarts during the write due to bogus residue values reported.

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Witold Lipieta <witold.lipieta@thaumatec.com>
Link: https://lore.kernel.org/r/20220809112911.462776-1-witold.lipieta@thaumatec.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the port does not support USB PD, prevent transition to PD
only states when power supply property is written. In this case,
TCPM transitions to SNK_NEGOTIATE_CAPABILITIES
which should not be the case given that the port is not pd_capable.

[   84.308251] state change SNK_READY -> SNK_NEGOTIATE_CAPABILITIES [rev3 NONE_AMS]
[   84.308335] Setting usb_comm capable false
[   84.323367] set_auto_vbus_discharge_threshold mode:3 pps_active:n vbus:5000 ret:0
[   84.323376] state change SNK_NEGOTIATE_CAPABILITIES -> SNK_WAIT_CAPABILITIES [rev3 NONE_AMS]

Fixes: e9e6e164

 ("usb: typec: tcpm: Support non-PD mode")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220817215410.1807477-1-badhri@google.com


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Turning on NOP_USB_XCEIV as builtin broke the TUSB6010 driver because
of an older issue with the depencency.

It is not necessary to forbid NOP_USB_XCEIV=y in combination with
USB_MUSB_HDRC=m, but only the reverse, which causes the link failure
from the original Kconfig change.

Use the correct dependency to still allow NOP_USB_XCEIV=n or
NOP_USB_XCEIV=y but forbid NOP_USB_XCEIV=m when USB_MUSB_HDRC=m
to fix the multi_v7_defconfig for tusb.

Fixes: ab37a7a8 ("ARM: multi_v7_defconfig: Make NOP_USB_XCEIV driver built-in")
Fixes: c0442479

 ("usb: musb: Fix randconfig build issues for Kconfig options")
Cc: stable <stable@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20220818135737.3143895-10-arnd@kernel.org


Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Only Thunderbolt 3 routers need the xHCI connection flow. This also
ensures the router actually has both lane adapters (1 and 3). While
there move declaration of the boolean variables inside the block where
they are being used.

Fixes: 30a4eca6

 ("thunderbolt: Add internal xHCI connect flows for Thunderbolt 3 devices")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The received notification packet is held in pkg->buffer and not in pkg
itself. Fix this by using the correct buffer.

Fixes: 81a54b5e

 ("thunderbolt: Let the connection manager handle all notifications")
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.

Fixes powerpc allmodconfig build:

   In file included from include/linux/nodemask.h:97,
                    from include/linux/mmzone.h:17,
                    from include/linux/gfp.h:7,
                    from include/linux/radix-tree.h:12,
                    from include/linux/idr.h:15,
                    from include/linux/kernfs.h:12,
                    from include/linux/sysfs.h:16,
                    from include/linux/kobject.h:20,
                    from include/linux/pci.h:35,
                    from arch/powerpc/kernel/prom_init.c:24:
   include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
      25 |         add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
         |                                              ^~~~~~~~~~~~~~
         |                                              add_latent_entropy
   include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in

Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull vfs lseek fix from Al Viro:
 "Fix proc_reg_llseek() breakage. Always had been possible if somebody
  left NULL ->proc_lseek, became a practical issue now"

* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  take care to handle NULL ->proc_lseek()

Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.

Fixes: 868941b1

 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>