Context information structure is going to be used in a000
devices for firmware self init.

The self init includes firmware self loading from DRAM by
ROM.
This means the TFH relevant firmware loading can be cleaned up.

The firmware loading includes the paging memory as well, so op
mode can stop initializing the paging and sending the DRAM_BLOCK_CMD.

Firmware is doing RFH, TFH and SCD configuration, while driver
only fills the required configurations and addresses in the
context information structure.

The only remaining access to RFH is the write pointer, which
is updated upon alive interrupt after FW configured the RFH.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

a000 devices are going to have a lot of flows simplified
and changed: init flow, RX, TX, and more.
This, combined with the fact that code is already very
complicated due to backward compatibility - introduce
a split that will enable to introduce simplified version
of functions.
Shared ops are moved to a macro, while functions that will
be updated in the next patches are defined twice for now.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We don't need this parameter anymore, since we always pass 0 anyway.
Remove it from the structure and from all the relevant functions.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In case of a MFUART assert, get a notification from the fw
that consists of the assert id and debug data.

The notification may be divided to multiple chunks, depending
on the size of the debug data sent to the driver, which would
be up to 1KB.

Get the notification, and if the debug info flag is enabled,
print the debug data to the dmesg.

Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Use iwl_get_dma_hi_addr() instead of open-coding it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This register is helpful for debugging D3 issues.
Driver turns all bits on, and then on exit reads the
updated value there.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We already have queue_used in the transport - we can
use it instead.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This reverts commit 8aacf4b7

 ("iwlwifi: introduce trans API
to get byte count table").
The commit is not needed as a better approach will be taken.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

In a000 devices FW will assign the queue number. Prepare for
that by getting rid of static defines and store them in variables.
Enlarge to u16 since we may have up to 512 queues.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Currently we release up to the last expired frame.
However, if there are consecutive frames after it - we can
optimize it further and release them as well - until the next
hole.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

The command was changed to support PN offload and TKIP offload.
The FW will do TKIP calculations in D0 only for a000 devices,
but API is aligned anyway.
However, for all devices we can stop sending the wowlan tkip
command.
Firmware will fetch the keys from the station key command.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Currently multicast queue is associated with the broadcast
station.

This raises quite a few issues:

The multicast queue has a special treatment:
- It is sent in the MAC context command
- It is excluded from tfd_queue_mask

In DQA mode we end up enabling two queues - the probe response
queue and the multicast queue - with the same station (broadcast)
and TID while in DQA mode it should be unique RA-TID.
Firmware will enforce it for a000 devices, so this allocation
will fail.

In addition, in a000 devices the FW will set the FIFO and not
the driver. So there is a need for FW to know when we enable
the queue that it is multicast queue so it will be bound to
the multicast FIFO. There is no such way in current design.

In order to simplify driver and firmware handling of this queue
create a multicast station.
This solves the unique RA-TID issue in the short term and serves
as preparation for the long term.

In the long term we will also add a flag marking this station for
the FW as the multicast station.
Once we will do that the FW will know this is the multicast queue
immediately when it is added and bind it to the correct FIFO.
It will also enable removing the special treatment of the
queue in the MAC context command.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Once we remove support for A-step, we'll be able to
clean the code back again.

Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

That's a bit nicer than open-coding it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.

In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.

The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.

When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

We don't need to print so much data in the kernel log.
Limit the data to be printed to the queue that actually
got stuck in case of a TFD queue hang, and stop dumping
all the CSR and FH registers. Over the course of time, the
CSR and FH values haven't proven themselves to be really
useful for debugging, and they are now in the firmware dump
anyway.

This comes as a preparation to the addition of more data
required to be printed by the firwmare team.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When receiving a frame, we currently pull in sizeof(*hdr) plus
some extra (crypto/snap), which is too much, most headers aren't
actually sizeof(*hdr) since that takes into account the 4-address
format but doesn't take into account QoS. As a result, a typical
frame will have 4 bytes of the payload in the SKB header already.

Fix this by calculating the correct header length, and now that
we have that, align the end of the SKB header to a multiple of 4
so that the IP header will be aligned properly when pulled in.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Final API has a reserved field - adjust accordingly.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

One of the RF modules we support has been deprecated and never
released publicly.  Remove support for this module.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

This will allow to print the name of the commands in the
logs when we sent it.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

If the supported firmware versions are not found, we currently only
print "no suitable firmware found".  This is not very informative for
the user trying to find the correct version to use.  Improve this by
printing the exact firmware name(s) the driver supports and pointing
to the git repository where they can be found.

Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

For a000 devices the binding API needs to include relevant
lmac ID - support the new API.
The new API should be used regardless if the device had CDB or
not. If there is no actual CDB support the binding is bound
to first lmac regardless of the band.
There are some functionality changes in binding restrictions
and quota allocations that will be handled in future patches.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

When IEEE80211_CHAN_RADAR is set by cfg80211, passive scan must be
performed. In mwifiex,active scan is performed even though flag is
set from cfg80211. mwifiex_reg_apply_radar_flags() function added
in this patch correctly uses radar flag.

Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Earlier versions of the FW did not support h2c to set GNT_BT, but later
versions have that capability. Hence we check the FW version and decide
whether to use h2c or just write to the register.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since btcoex uses static variables to store the cumulative information
on the wifi status, some tricks are used that are a bit obscure. We add
some comments about the criteria we use to adjust wifi duration.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The bt can specify a power level to decrease. Rather than decreasing by a
fixed value (usually 2), this change makes the driver fit to the
environment more quickly.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

New ICs have hardware mailbox to deliver bt information instead of doing
it by driver itself, so remove them.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

set coex table fine tune, for register settings

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The larger the bt a2dp bit pool is, the more time bt needs to receive
them. If we do not adjust the wifi duration, the voice quality will be
low. Hence we reduce the time that wifi holds, to improve the a2dp
service.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

modify h2c parameter so that the rate suffers less penalty from retry

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If there are too many CRC error packets, it means the wifi is operating
under low quality circumstances. If so, we need to reallocate the
resources of wifi and bt

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

if the bt is slave, it may receive packet at any time, so we
need to mark them as high priority packets to avoid packet loss.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For wifi and bt coexistence, if the aggregation size of wifi is too
large, the transmission time of the aggregated packet could be too long
and the bt packets might "cut off" the wifi packet. We need to reduce
the aggregation size to improve wifi performance.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix a number of checkpatch.pl warnings. In addition, some variable and
function names are shortened, and/or renamed to be more consistent.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

A number of functions in the Bluetooth Coexistence routines are not used,
and can be removed.

Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In mwifiex,IEs such as supported channels, supported operating classes
20/40 BSS COexistence are missing and also extra QOS capabilities IE
is added during TDLS discovery response, TDLS setup request and
TDLS setupresponse.
This patch adds require IEs and also removes extra IE.

Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

trivial fix to spelling mistakes in wl1271_warning error message, change
iligal to invalid and opperation to operation.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When resetting the device, we take a synchronous firmware-loading code
path, which borrows a lot from the asynchronous path used at probe time.
We don't catch errors correctly though, which means that in the PCIe
driver, we may try to dereference the 'adapter' struct after
mwifiex_fw_dpc() has freed it. See this (erronous) print in
mwifiex_pcie_reset_notify():

	mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__);

Let's instead refactor the synchronous (or "!req_fw_nowait") path so
that we propagate errors and handle them properly.

This fixes a use-after-free issue in the PCIe driver, as well as a
misleading debug message ("successful"). It looks like the SDIO driver
doesn't have these problems, since it doesn't do anything after
mwifiex_reinit_sw().

Fixes: 4c5dae59

 ("mwifiex: add PCIe function level reset support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If we fail to reinit the FW when resetting the device (in the
synchronous version of mwifiex_init_hw_fw() -> mwifiex_fw_dpc()),
mwifiex_fw_dpc() will tear down the interface and free up the adapter.
But we don't actually check for all failure cases of mwifiex_fw_dpc(),
so some of them fall through and dereference adapter->fw_done with a
freed adapter, causing a use-after-free bug.

In any case, mwifiex_fw_dpc() will always signal FW completion -- in the
error OR success case -- so at best, this was repeat work. Let's not do
it.

Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>