The RIPS register is used to store IPv6 addresses for use by the NVE and
IP-in-IP.

For IPv6 underlay support, RATR register needs to hold a pointer to the
remote IPv6 address for encapsulation and RTDP register needs to hold a
pointer to the local IPv6 address for decapsulation check.

Add the required register for saving IPv6 addresses.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function __mlxsw_sp_ipip_netdev_ul_dev_get() returns the underlay
device that corresponds to the overlay device that it gets.
Currently, this function assumes that the tunnel is IPv4 GRE, because it
is the only one that is supported by mlxsw driver.

This assumption will no longer be correct when IPv6 GRE support is added,
resulting in wrong underlay device being returned.
Instead, check 'ol_dev->type' and return the underlay device accordingly.

Move the function to spectrum_ipip.c because spectrum_router.c should not
be aware to tunnel type.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function mlxsw_sp_ipip_ol_netdev_change_gre4() contains code that
can be shared between IPv4 and IPv6.
The only difference is the way that arguments are taken from tunnel
parameters, which are different between IPv4 and IPv6.

For that, add structure 'mlxsw_sp_ipip_parms' to hold all the required
parameters for the function and save it as part of
'struct mlxsw_sp_ipip_entry' instead of the existing structure that is
not shared between IPv4 and IPv6. Add new operation as part of
'mlxsw_sp_ipip_ops' to initialize the new structure.

Then mlxsw_sp_ipip_ol_netdev_change_gre{4,6}() will prepare the new
structure and both will call the same function.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Suppress the following checkpatch.pl check [1] by adding a variable to
store the IP-in-IP options. Noticed while adding equivalent IPv6 code in
subsequent patches.

[1]
CHECK: Alignment should match open parenthesis
+               mlxsw_reg_ritr_loopback_ipip4_pack(ritr_pl, lb_cf.lb_ipipt,
+
+ MLXSW_REG_RITR_LOOPBACK_IPIP_OPTIONS_GRE_KEY_PRESET,

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, there are several functions that handle 'struct ip_tunnel_parm'
and 'struct __ip6_tnl_parm'.

Change the mentioned functions to get IP tunnel parameters by reference
and as 'const'.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw_sp_fib4_entry_type_unset() is not specific for IPv4 FIB entry,
move the code to mlxsw_sp_fib_entry_type_unset(), and call this function
from mlxsw_sp_fib4_entry_type_unset() so then it will be used for IPv6
also.

Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/mptcp/protocol.c
  977d293e ("mptcp: ensure tx skbs always have the MPTCP ext")
  efe686ff

 ("mptcp: ensure tx skbs always have the MPTCP ext")

same patch merged in both trees, keep net-next.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull networking fixes from Jakub Kicinski:
 "Current release - regressions:

   - dsa: bcm_sf2: fix array overrun in bcm_sf2_num_active_ports()

  Previous releases - regressions:

   - introduce a shutdown method to mdio device drivers, and make DSA
     switch drivers compatible with masters disappearing on shutdown;
     preventing infinite reference wait

   - fix issues in mdiobus users related to ->shutdown vs ->remove

   - virtio-net: fix pages leaking when building skb in big mode

   - xen-netback: correct success/error reporting for the
     SKB-with-fraglist

   - dsa: tear down devlink port regions when tearing down the devlink
     port on error

   - nexthop: fix division by zero while replacing a resilient group

   - hns3: check queue, vf, vlan ids range before using

  Previous releases - always broken:

   - napi: fix race against netpoll causing NAPI getting stuck

   - mlx4_en: ensure link operstate is updated even if link comes up
     before netdev registration

   - bnxt_en: fix TX timeout when TX ring size is set to the smallest

   - enetc: fix illegal access when reading affinity_hint; prevent oops
     on sysfs access

   - mtk_eth_soc: avoid creating duplicate offload entries

  Misc:

   - core: correct the sock::sk_lock.owned lockdep annotations"

* tag 'net-5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (51 commits)
  atlantic: Fix issue in the pm resume flow.
  net/mlx4_en: Don't allow aRFS for encapsulated packets
  net: mscc: ocelot: fix forwarding from BLOCKING ports remaining enabled
  net: ethernet: mtk_eth_soc: avoid creating duplicate offload entries
  nfc: st-nci: Add SPI ID matching DT compatible
  MAINTAINERS: remove Guvenc Gulce as net/smc maintainer
  nexthop: Fix memory leaks in nexthop notification chain listeners
  mptcp: ensure tx skbs always have the MPTCP ext
  qed: rdma - don't wait for resources under hw error recovery flow
  s390/qeth: fix deadlock during failing recovery
  s390/qeth: Fix deadlock in remove_discipline
  s390/qeth: fix NULL deref in qeth_clear_working_pool_list()
  net: dsa: realtek: register the MDIO bus under devres
  net: dsa: don't allocate the slave_mii_bus using devres
  Doc: networking: Fox a typo in ice.rst
  net: dsa: fix dsa_tree_setup error path
  net/smc: fix 'workqueue leaked lock' in smc_conn_abort_work
  net/smc: add missing error check in smc_clc_prfx_set()
  net: hns3: fix a return value error in hclge_get_reset_status()
  net: hns3: check vlan id before using it
  ...

Prior to the commit 7e1c0d6f ("memcg: switch lruvec stats to rstat")
and the commit aa48e47e ("memcg: infrastructure to flush memcg
stats"), each lruvec memcg stats can be off by (nr_cgroups * nr_cpus *
32) at worst and for unbounded amount of time.  The commit aa48e47e
moved the lruvec stats to rstat infrastructure and the commit
7e1c0d6f bounded the error for all the lruvec stats to (nr_cpus *
32) at worst for at most 2 seconds.  More specifically it decoupled the
number of stats and the number of cgroups from the error rate.

However this reduction in error comes with the cost of triggering the
slowpath of stats update more frequently.  Previously in the slowpath
the kernel adds the stats up the memcg tree.  After aa48e47e, the
kernel triggers the asyn lruvec stats flush through queue_work().  This
causes regression reports from 0day kernel bot [1] as well as from
phoronix test suite [2].

We tried two options to fix the regression:

 1) Increase the threshold to trigger the slowpath in lruvec stats
    update codepath from 32 to 512.

 2) Remove the slowpath from lruvec stats update codepath and instead
    flush the stats in the page refault codepath. The assumption is that
    the kernel timely flush the stats, so, the update tree would be
    small in the refault codepath to not cause the preformance impact.

Following are the results of will-it-scale/page_fault[1|2|3] benchmark
on four settings i.e.  (1) 5.15-rc1 as baseline (2) 5.15-rc1 with
aa48e47e and 7e1c0d6f reverted (3) 5.15-rc1 with option-1
(4) 5.15-rc1 with option-2.

  test       (1)      (2)               (3)               (4)
  pg_f1   368563   406277 (10.23%)   399693  (8.44%)   416398 (12.97%)
  pg_f2   338399   372133  (9.96%)   369180  (9.09%)   381024 (12.59%)
  pg_f3   500853   575399 (14.88%)   570388 (13.88%)   576083 (15.02%)

From the above result, it seems like the option-2 not only solves the
regression but also improves the performance for at least these
benchmarks.

Feng Tang (intel) ran the aim7 benchmark with these two options and
confirms that option-1 reduces the regression but option-2 removes the
regression.

Michael Larabel (phoronix) ran multiple benchmarks with these options
and reported the results at [3] and it shows for most benchmarks
option-2 removes the regression introduced by the commit aa48e47e
("memcg: infrastructure to flush memcg stats").

Based on the experiment results, this patch proposed the option-2 as the
solution to resolve the regression.

Link: https://lore.kernel.org/all/20210726022421.GB21872@xsang-OptiPlex-9020 [1]
Link: https://www.phoronix.com/scan.php?page=article&item=linux515-compile-regress [2]
Link: https://openbenchmarking.org/result/2109226-DEBU-LINUX5104 [3]
Fixes: aa48e47e

 ("memcg: infrastructure to flush memcg stats")
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Tested-by: Michael Larabel <Michael@phoronix.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Roman Gushchin <guro@fb.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Hillf Danton <hdanton@sina.com>,
Cc: Michal Koutný <mkoutny@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>,
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After fixing hibernation resume flow, another usecase was found which
should be explicitly handled - resume when device is in "down" state.
Invoke aq_nic_init jointly with aq_nic_start only if ndev was already
up during suspend/hibernate. We still need to perform nic_deinit() if
caller requests for it, to handle the freeze/resume scenarios.

Fixes: 57f780f1

 ("atlantic: Fix driver resume flow.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver doesn't support aRFS for encapsulated packets, return early error
in such a case.

Fixes: 1eb8c695

 ("net/mlx4_en: Add accelerated RFS support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The blamed commit made the fatally incorrect assumption that ports which
aren't in the FORWARDING STP state should not have packets forwarded
towards them, and that is all that needs to be done.

However, that logic alone permits BLOCKING ports to forward to
FORWARDING ports, which of course allows packet storms to occur when
there is an L2 loop.

The ocelot_get_bridge_fwd_mask should not only ask "what can the bridge
do for you", but "what can you do for the bridge". This way, only
FORWARDING ports forward to the other FORWARDING ports from the same
bridging domain, and we are still compatible with the idea of multiple
bridges.

Fixes: df291e54

 ("net: ocelot: support multiple bridges")
Suggested-by: Colin Foster <colin.foster@in-advantage.com>
Reported-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes multiple CLS_REPLACE calls are issued for the same connection.
rhashtable_insert_fast does not check for these duplicates, so multiple
hardware flow entries can be created.
Fix this by checking for an existing entry early

Fixes: 502e84e2

 ("net: ethernet: mtk_eth_soc: add flow offloading support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the sja1105 driver is finally sane enough again to stop having
a ternary VLAN awareness state, we can remove priv->vlan_aware and query
DSA for the ds->vlan_filtering value (for SJA1105, VLAN filtering is a
global property).

Also drop the paranoid checking that DSA calls ->port_vlan_filtering
multiple times without the VLAN awareness state changing. It doesn't,
the same check is present inside dsa_port_vlan_filtering too.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding the part name used in
the compatible to the list of SPI IDs.

Fixes: 96c8395e

 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove myself as net/smc maintainer, as I am
leaving IBM soon and can not maintain net/smc anymore.

Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
net: remove sk skb caches

Eric noted we would be better off reverting the sk
skb caches.

MPTCP relies on such a feature, so we need a
little refactor of the MPTCP tx path before the mentioned
revert.

The first patch exposes additional TCP helpers. The 2nd patch
changes the MPTCP code to do locally the whole skb allocation
and updating, so it does not rely anymore on core TCP helpers
for that nor the sk skb cache.

As a side effect, we can make the tcp_build_frag helper static.

Finally, we can pull Eric's revert.

RFC -> v1:
 - drop driver specific patch - no more needed after helper rename
 - rename skb_entail -> tcp_skb_entail (Eric)
 - preserve the tcp_build_frag helpwe, just make it static (Eric)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts the following patches :

- commit 2e05fcae ("tcp: fix compile error if !CONFIG_SYSCTL")
- commit 4f661542 ("tcp: fix zerocopy and notsent_lowat issues")
- commit 472c2e07 ("tcp: add one skb cache for tx")
- commit 8b27dae5

 ("tcp: add one skb cache for rx")

Having a cache of one skb (in each direction) per TCP socket is fragile,
since it can cause a significant increase of memory needs,
and not good enough for high speed flows anyway where more than one skb
is needed.

We want instead to add a generic infrastructure, with more flexible
per-cpu caches, for alien NUMA nodes.

Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch the mentioned helper is
used only inside its compilation unit: let's make
it static.

RFC -> v1:
 - preserve the tcp_build_frag() helper (Eric)

Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to revert the skb TX cache, but MPTCP is currently
using it unconditionally.

Rework the MPTCP tx code, so that tcp_tx_skb_cache is not
needed anymore: do the whole coalescing check, skb allocation
skb initialization/update inside mptcp_sendmsg_frag(), quite
alike the current TCP code.

Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

the tcp_skb_entail() helper is actually skb_entail(), renamed
to provide proper scope.

    The two helper will be used by the next patch.

RFC -> v1:
 - rename skb_entail to tcp_skb_entail (Eric)

Acked-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to signed/unsigned comparison, the expression:

	info->size_goal - skb->len > 0

evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.

Due to the above, syzbot is able to trigger the following WARN_ON():

WARNING: CPU: 1 PID: 810 at net/mptcp/protocol.c:1366 mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Modules linked in:
CPU: 1 PID: 810 Comm: syz-executor.4 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Code: ff 4c 8b 74 24 50 48 8b 5c 24 58 e9 0f fb ff ff e8 13 44 8b f8 4c 89 e7 45 31 ed e8 98 57 2e fe e9 81 f4 ff ff e8 fe 43 8b f8 <0f> 0b 41 bd ea ff ff ff e9 6f f4 ff ff 4c 89 e7 e8 b9 8e d2 f8 e9
RSP: 0018:ffffc9000531f6a0 EFLAGS: 00010216
RAX: 000000000000697f RBX: 0000000000000000 RCX: ffffc90012107000
RDX: 0000000000040000 RSI: ffffffff88eac9e2 RDI: 0000000000000003
RBP: ffff888078b15780 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff88eac017 R11: 0000000000000000 R12: ffff88801de0a280
R13: 0000000000006b58 R14: ffff888066278280 R15: ffff88803c2fe9c0
FS:  00007fd9f866e700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007faebcb2f718 CR3: 00000000267cb000 CR4: 00000000001506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __mptcp_push_pending+0x1fb/0x6b0 net/mptcp/protocol.c:1547
 mptcp_release_cb+0xfe/0x210 net/mptcp/protocol.c:3003
 release_sock+0xb4/0x1b0 net/core/sock.c:3206
 sk_stream_wait_memory+0x604/0xed0 net/core/stream.c:145
 mptcp_sendmsg+0xc39/0x1bc0 net/mptcp/protocol.c:1749
 inet6_sendmsg+0x99/0xe0 net/ipv6/af_inet6.c:643
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:724
 sock_write_iter+0x2a0/0x3e0 net/socket.c:1057
 call_write_iter include/linux/fs.h:2163 [inline]
 new_sync_write+0x40b/0x640 fs/read_write.c:507
 vfs_write+0x7cf/0xae0 fs/read_write.c:594
 ksys_write+0x1ee/0x250 fs/read_write.c:647
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x4665f9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fd9f866e188 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000056c038 RCX: 00000000004665f9
RDX: 00000000000e7b78 RSI: 0000000020000000 RDI: 0000000000000003
RBP: 00000000004bfcc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000056c038
R13: 0000000000a9fb1f R14: 00007fd9f866e300 R15: 0000000000022000

Fix the issue rewriting the relevant expression to avoid
sign-related problems - note: size_goal is always >= 0.

Additionally, ensure that the skb in the tx cache always carries
the relevant extension.

Reported-and-tested-by:  <syzbot+263a248eec3e875baa7b@syzkaller.appspotmail.com>
Fixes: 1094c6fe

 ("mptcp: fix possible divide by zero")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver only needs the reset GPIO for a very brief period, so instead
of using devres and keeping the descriptor pointer inside priv, just use
that descriptor inside the sja1105_hw_reset function and then let go of
it.

Also use gpiod_get_optional while at it, and error out on real errors
(bad flags etc).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Fix circular dependency between sja1105 and tag_sja1105

As discussed here:
https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/


DSA tagging protocols cannot use symbols exported by switch drivers.

Eliminate the two instances of that from tag_sja1105, and that allows us
to have a working setup with modules again.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

It's nice to be able to test a tagging protocol with dsa_loop, but not
at the cost of losing the ability of building the tagging protocol and
switch driver as modules, because as things stand, there is a circular
dependency between the two. Tagging protocol drivers cannot depend on
switch drivers, that is a hard fact.

The reasoning behind the blamed patch was that accessing dp->priv should
first make sure that the structure behind that pointer is what we really
think it is.

Currently the "sja1105" and "sja1110" tagging protocols only operate
with the sja1105 switch driver, just like any other tagging protocol and
switch combination. The only way to mix and match them is by modifying
the code, and this applies to dsa_loop as well (by default that uses
DSA_TAG_PROTO_NONE). So while in principle there is an issue, in
practice there isn't one.

Until we extend dsa_loop to allow user space configuration, treat the
problem as a non-issue and just say that DSA ports found by tag_sja1105
are always sja1105 ports, which is in fact true. But keep the
dsa_port_is_sja1105 function so that it's easy to patch it during
testing, and rely on dead code elimination.

Fixes: 994d2cbb ("net: dsa: tag_sja1105: be dsa_loop-safe")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/


Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The problem is that DSA tagging protocols really must not depend on the
switch driver, because this creates a circular dependency at insmod
time, and the switch driver will effectively not load when the tagging
protocol driver is missing.

The code was structured in the way it was for a reason, though. The DSA
driver-facing API for PTP timestamping relies on the assumption that
two-step TX timestamps are provided by the hardware in an out-of-band
manner, typically by raising an interrupt and making that timestamp
available inside some sort of FIFO which is to be accessed over
SPI/MDIO/etc.

So the API puts .port_txtstamp into dsa_switch_ops, because it is
expected that the switch driver needs to save some state (like put the
skb into a queue until its TX timestamp arrives).

On SJA1110, TX timestamps are provided by the switch as Ethernet
packets, so this makes them be received and processed by the tagging
protocol driver. This in itself is great, because the timestamps are
full 64-bit and do not require reconstruction, and since Ethernet is the
fastest I/O method available to/from the switch, PTP timestamps arrive
very quickly, no matter how bottlenecked the SPI connection is, because
SPI interaction is not needed at all.

DSA's code structure and strict isolation between the tagging protocol
driver and the switch driver break the natural code organization.

When the tagging protocol driver receives a packet which is classified
as a metadata packet containing timestamps, it passes those timestamps
one by one to the switch driver, which then proceeds to compare them
based on the recorded timestamp ID that was generated in .port_txtstamp.

The communication between the tagging protocol and the switch driver is
done through a method exported by the switch driver, sja1110_process_meta_tstamp.
To satisfy build requirements, we force a dependency to build the
tagging protocol driver as a module when the switch driver is a module.
However, as explained in the first paragraph, that causes the circular
dependency.

To solve this, move the skb queue from struct sja1105_private :: struct
sja1105_ptp_data to struct sja1105_private :: struct sja1105_tagger_data.
The latter is a data structure for which hacks have already been put
into place to be able to create persistent storage per switch that is
accessible from the tagging protocol driver (see sja1105_setup_ports).

With the skb queue directly accessible from the tagging protocol driver,
we can now move sja1110_process_meta_tstamp into the tagging driver
itself, and avoid exporting a symbol.

Fixes: 566b18c8 ("net: dsa: sja1105: implement TX timestamping for SJA1110")
Link: https://lore.kernel.org/netdev/20210908220834.d7gmtnwrorhharna@skbuf/


Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It looks like this field was never used since its introduction in commit
227d07a0

 ("net: dsa: sja1105: Add support for traffic through
standalone ports") remove it.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzkaller discovered memory leaks [1] that can be reduced to the
following commands:

 # ip nexthop add id 1 blackhole
 # devlink dev reload pci/0000:06:00.0

As part of the reload flow, mlxsw will unregister its netdevs and then
unregister from the nexthop notification chain. Before unregistering
from the notification chain, mlxsw will receive delete notifications for
nexthop objects using netdevs registered by mlxsw or their uppers. mlxsw
will not receive notifications for nexthops using netdevs that are not
dismantled as part of the reload flow. For example, the blackhole
nexthop above that internally uses the loopback netdev as its nexthop
device.

One way to fix this problem is to have listeners flush their nexthop
tables after unregistering from the notification chain. This is
error-prone as evident by this patch and also not symmetric with the
registration path where a listener receives a dump of all the existing
nexthops.

Therefore, fix this problem by replaying delete notifications for the
listener being unregistered. This is symmetric to the registration path
and also consistent with the netdev notification chain.

The above means that unregister_nexthop_notifier(), like
register_nexthop_notifier(), will have to take RTNL in order to iterate
over the existing nexthops and that any callers of the function cannot
hold RTNL. This is true for mlxsw and netdevsim, but not for the VXLAN
driver. To avoid a deadlock, change the latter to unregister its nexthop
listener without holding RTNL, making it symmetric to the registration
path.

[1]
unreferenced object 0xffff88806173d600 (size 512):
  comm "syz-executor.0", pid 1290, jiffies 4295583142 (age 143.507s)
  hex dump (first 32 bytes):
    41 9d 1e 60 80 88 ff ff 08 d6 73 61 80 88 ff ff  A..`......sa....
    08 d6 73 61 80 88 ff ff 01 00 00 00 00 00 00 00  ..sa............
  backtrace:
    [<ffffffff81a6b576>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
    [<ffffffff81a6b576>] slab_post_alloc_hook+0x96/0x490 mm/slab.h:522
    [<ffffffff81a716d3>] slab_alloc_node mm/slub.c:3206 [inline]
    [<ffffffff81a716d3>] slab_alloc mm/slub.c:3214 [inline]
    [<ffffffff81a716d3>] kmem_cache_alloc_trace+0x163/0x370 mm/slub.c:3231
    [<ffffffff82e8681a>] kmalloc include/linux/slab.h:591 [inline]
    [<ffffffff82e8681a>] kzalloc include/linux/slab.h:721 [inline]
    [<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_group_create drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:4918 [inline]
    [<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_new drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5054 [inline]
    [<ffffffff82e8681a>] mlxsw_sp_nexthop_obj_event+0x59a/0x2910 drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c:5239
    [<ffffffff813ef67d>] notifier_call_chain+0xbd/0x210 kernel/notifier.c:83
    [<ffffffff813f0662>] blocking_notifier_call_chain kernel/notifier.c:318 [inline]
    [<ffffffff813f0662>] blocking_notifier_call_chain+0x72/0xa0 kernel/notifier.c:306
    [<ffffffff8384b9c6>] call_nexthop_notifiers+0x156/0x310 net/ipv4/nexthop.c:244
    [<ffffffff83852bd8>] insert_nexthop net/ipv4/nexthop.c:2336 [inline]
    [<ffffffff83852bd8>] nexthop_add net/ipv4/nexthop.c:2644 [inline]
    [<ffffffff83852bd8>] rtm_new_nexthop+0x14e8/0x4d10 net/ipv4/nexthop.c:2913
    [<ffffffff833e9a78>] rtnetlink_rcv_msg+0x448/0xbf0 net/core/rtnetlink.c:5572
    [<ffffffff83608703>] netlink_rcv_skb+0x173/0x480 net/netlink/af_netlink.c:2504
    [<ffffffff833de032>] rtnetlink_rcv+0x22/0x30 net/core/rtnetlink.c:5590
    [<ffffffff836069de>] netlink_unicast_kernel net/netlink/af_netlink.c:1314 [inline]
    [<ffffffff836069de>] netlink_unicast+0x5ae/0x7f0 net/netlink/af_netlink.c:1340
    [<ffffffff83607501>] netlink_sendmsg+0x8e1/0xe30 net/netlink/af_netlink.c:1929
    [<ffffffff832fde84>] sock_sendmsg_nosec net/socket.c:704 [inline]
    [<ffffffff832fde84>] sock_sendmsg net/socket.c:724 [inline]
    [<ffffffff832fde84>] ____sys_sendmsg+0x874/0x9f0 net/socket.c:2409
    [<ffffffff83304a44>] ___sys_sendmsg+0x104/0x170 net/socket.c:2463
    [<ffffffff83304c01>] __sys_sendmsg+0x111/0x1f0 net/socket.c:2492
    [<ffffffff83304d5d>] __do_sys_sendmsg net/socket.c:2501 [inline]
    [<ffffffff83304d5d>] __se_sys_sendmsg net/socket.c:2499 [inline]
    [<ffffffff83304d5d>] __x64_sys_sendmsg+0x7d/0xc0 net/socket.c:2499

Fixes: 2a014b20

 ("mlxsw: spectrum_router: Add support for nexthop objects")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f8ade8dd ("xsurf100: drop include of lib8390.c") accidentally
changed init/main.c.  Revert that part.

Fixes: f8ade8dd

 ("xsurf100: drop include of lib8390.c")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Juergen, Roger, and Stefano.

Thank you!

Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Roger Pau Monné <roger.pau@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Konrad's new job role is putting a serious cramp on him
being a responsive maintainer and as such he is handing off
the reins to Christoph Hellwig.

Thank you!

Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Ley Foon has left Intel and will no longer be able to maintain NIOS2.
Update the MAINTAINER's entry to Dinh Nguyen.

Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull spi modalias fix from Mark Brown:
 "Fix modalias issues

  As reported by Russell King the change to use OF style modaliases for
  DT enumerated broke at least the spi-nor driver, the patch here
  reverts that change to fix the regression.

  Sadly this will mean that anything that started loading since the
  change to OF modaliases will run into issues, there doesn't seem to be
  any approach which doesn't cause some problems and thi seems like the
  least bad approach - gory details are in the commit log for the
  change.

  I'm currently working through the SPI drivers to add ID tables and
  missing IDs to tables which should address things from the other end,
  this seems more straightforward and robust than any other options"

* tag 'spi-fix-v5.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: Revert modalias changes

Pull nfsd fixes from Chuck Lever:
 "Critical bug fixes:

   - Fix crash in NLM TEST procedure

   - NFSv4.1+ backchannel not restored after PATH_DOWN"

* tag 'nfsd-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  nfsd: back channel stuck in SEQ4_STATUS_CB_PATH_DOWN
  NLM: Fix svcxdr_encode_owner()

Merge tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver fixes from Hans de Goede:
 "The first round of bug-fixes for platform-drivers-x86 for 5.15,
  highlights:

   - amd-pmc fix for some suspend/resume issues

   - intel-hid fix to avoid false-positive SW_TABLET_MODE=1 reporting

   - some build error/warning fixes

   - various DMI quirk additions"

* tag 'platform-drivers-x86-v5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86: gigabyte-wmi: add support for B550I Aorus Pro AX
  platform/x86/intel: hid: Add DMI switches allow list
  platform/x86: dell: fix DELL_WMI_PRIVACY dependencies & build error
  platform/x86: amd-pmc: Increase the response register timeout
  platform/x86: touchscreen_dmi: Update info for the Chuwi Hi10 Plus (CWI527) tablet
  platform/x86: touchscreen_dmi: Add info for the Chuwi HiBook (CWI514) tablet
  lg-laptop: Correctly handle dmi_get_system_info() returning NULL
  platform/x86/intel: punit_ipc: Drop wrong use of ACPI_PTR()

linux@prisktech.co.nz is defunct:

  4.1.2 <linux@prisktech.co.nz>: Recipient address rejected: Domain not found

Remove it from MAINTAINERS and mark the ARM/VT8500 entry orphan.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Due to signed/unsigned comparison, the expression:

	info->size_goal - skb->len > 0

evaluates to true when the size goal is smaller than the
skb size. That results in lack of tx cache refill, so that
the skb allocated by the core TCP code lacks the required
MPTCP skb extensions.

Due to the above, syzbot is able to trigger the following WARN_ON():

WARNING: CPU: 1 PID: 810 at net/mptcp/protocol.c:1366 mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Modules linked in:
CPU: 1 PID: 810 Comm: syz-executor.4 Not tainted 5.14.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:mptcp_sendmsg_frag+0x1362/0x1bc0 net/mptcp/protocol.c:1366
Code: ff 4c 8b 74 24 50 48 8b 5c 24 58 e9 0f fb ff ff e8 13 44 8b f8 4c 89 e7 45 31 ed e8 98 57 2e fe e9 81 f4 ff ff e8 fe 43 8b f8 <0f> 0b 41 bd ea ff ff ff e9 6f f4 ff ff 4c 89 e7 e8 b9 8e d2 f8 e9
RSP: 0018:ffffc9000531f6a0 EFLAGS: 00010216
RAX: 000000000000697f RBX: 0000000000000000 RCX: ffffc90012107000
RDX: 0000000000040000 RSI: ffffffff88eac9e2 RDI: 0000000000000003
RBP: ffff888078b15780 R08: 0000000000000000 R09: 0000000000000000
R10: ffffffff88eac017 R11: 0000000000000000 R12: ffff88801de0a280
R13: 0000000000006b58 R14: ffff888066278280 R15: ffff88803c2fe9c0
FS:  00007fd9f866e700(0000) GS:ffff8880b9d00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007faebcb2f718 CR3: 00000000267cb000 CR4: 00000000001506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __mptcp_push_pending+0x1fb/0x6b0 net/mptcp/protocol.c:1547
 mptcp_release_cb+0xfe/0x210 net/mptcp/protocol.c:3003
 release_sock+0xb4/0x1b0 net/core/sock.c:3206
 sk_stream_wait_memory+0x604/0xed0 net/core/stream.c:145
 mptcp_sendmsg+0xc39/0x1bc0 net/mptcp/protocol.c:1749
 inet6_sendmsg+0x99/0xe0 net/ipv6/af_inet6.c:643
 sock_sendmsg_nosec net/socket.c:704 [inline]
 sock_sendmsg+0xcf/0x120 net/socket.c:724
 sock_write_iter+0x2a0/0x3e0 net/socket.c:1057
 call_write_iter include/linux/fs.h:2163 [inline]
 new_sync_write+0x40b/0x640 fs/read_write.c:507
 vfs_write+0x7cf/0xae0 fs/read_write.c:594
 ksys_write+0x1ee/0x250 fs/read_write.c:647
 do_syscall_x64 arch/x86/entry/common.c:50 [inline]
 do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
 entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x4665f9
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fd9f866e188 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000056c038 RCX: 00000000004665f9
RDX: 00000000000e7b78 RSI: 0000000020000000 RDI: 0000000000000003
RBP: 00000000004bfcc4 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000056c038
R13: 0000000000a9fb1f R14: 00007fd9f866e300 R15: 0000000000022000

Fix the issue rewriting the relevant expression to avoid
sign-related problems - note: size_goal is always >= 0.

Additionally, ensure that the skb in the tx cache always carries
the relevant extension.

Reported-and-tested-by:  <syzbot+263a248eec3e875baa7b@syzkaller.appspotmail.com>
Fixes: 1094c6fe

 ("mptcp: fix possible divide by zero")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the HW device is during recovery, the HW resources will never return,
hence we shouldn't wait for the CID (HW context ID) bitmaps to clear.
This fix speeds up the error recovery flow.

Fixes: 64515dc8

 ("qed: Add infrastructure for error detection and recovery")
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Shai Malin <smalin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Alter trap adjacency entry allocation scheme

In commit 0c3cbbf9 ("mlxsw: Add specific trap for packets routed via
invalid nexthops"), mlxsw started allocating a new adjacency entry
during driver initialization, to trap packets routed via invalid
nexthops.

This behavior was later altered in commit 983db619

 ("mlxsw:
spectrum_router: Allocate discard adjacency entry when needed") to only
allocate the entry upon the first route that requires it. The motivation
for the change is explained in the commit message.

The problem with the current behavior is that the entry shows up as a
"leak" in a new BPF resource monitoring tool [1]. This is caused by the
asymmetry of the allocation/free scheme. While the entry is allocated
upon the first route that requires it, it is only freed during
de-initialization of the driver.

Instead, this patchset tracks the number of active nexthop groups and
allocates the adjacency entry upon the creation of the first group. The
entry is freed when the number of active groups reaches zero.

Patch #1 adds the new entry.

Patch #2 converts mlxsw to start using the new entry and removes the old
one.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Start using the trap adjacency entry that was added in the previous
patch and remove the existing one which is no longer needed.

Note that the name of the old entry was inaccurate as the entry did not
discard packets, but trapped them.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>