- Mar 18, 2020
-
-
Eli Cohen authored
Don't use termination tables for packets that are steered to the slow path, as a pre-step for supporting packet encap (packet reformat) action on termination tables. Packet encap (reformat action) actions steer the packet to the slow path until outer arp entries are resolved. Signed-off-by:
Eli Cohen <eli@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Eli Cohen authored
Check if QoS is enabled for the eswitch before attempting to configure QoS parameters and emit a netlink error if not supported. Introduce an API to check if QoS is supported for the eswitch. Signed-off-by:
Eli Cohen <eli@mellanox.com> Reviewed-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Paul Blakey <paulb@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Vladyslav Tarasiuk authored
If udevd is configured to rename interfaces according to persistent naming rules and if a network interface has phys_port_name in sysfs, its contents will be appended to the interface name. However, register_netdev creates device in sysfs and if devlink_port_register is called after that, there is a timeframe in which udevd may read an empty phys_port_name value. The consequence is that the interface will lose this suffix and its name will not be really persistent. The solution is to register the port before registering a netdev. Fixes: c6acd629 ("net/mlx5e: Add support for devlink-port in non-representors mode") Signed-off-by:
Vladyslav Tarasiuk <vladyslavt@mellanox.com> Reviewed-by:
Maxim Mikityanskiy <maximmi@mellanox.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Roi Dayan authored
The original condition rejected all egress rules that are not on tunnel device. Also, the whole point of this egress reject was to disallow bad rules because of egdev which doesn't exists today, so remove this check entirely. Fixes: 0a7fcb78 ("net/mlx5e: Support inner header rewrite with goto action") Signed-off-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Reviewed-by:
Vlad Buslov <vladbu@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Paul Blakey authored
Register loopback which is needed for tunnel restoration, is now always enabled if supported and not just with metadata enabled, check for that instead. Signed-off-by:
Paul Blakey <paulb@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Saeed Mahameed authored
Fix the following warnings: [-Werror=frame-larger-than=] In function ‘mlx5_tc_ct_entry_add_rule’: drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:541:1: error: the frame size of 1136 bytes is larger than 1024 bytes In function ‘__mlx5_tc_ct_flow_offload’: drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:1049:1: error: the frame size of 1168 bytes is larger than 1024 bytes Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking") Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Reviewed-by:
Paul Blakey <paulb@mellanox.com>
-
Paul Blakey authored
If CONFIG_MLX5_TC_CT isn't enabled, all offloading of eswitch tc rules fails on parsing ct match, even if there is no ct match. Return success if there is no ct match, regardless of config. Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking") Signed-off-by:
Paul Blakey <paulb@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
YueHaibing authored
drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c: In function mlx5_tc_ct_parse_match: drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.c:699:36: warning: variable unnew set but not used [-Wunused-but-set-variable] Fixes: 4c3844d9 ("net/mlx5e: CT: Introduce connection tracking") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Paul Blakey authored
Restore modify header writes the chain mapping on the packet. This modify header and action is added on all prios connections, and gets overwritten with the same value consecutively in prios of the same chain. Use the chain's modify header only for the last prio of a given tc chain. Signed-off-by:
Paul Blakey <paulb@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Paul Blakey authored
Currently, if firmware doesn't support fwd and modify, driver fails initializing eswitch chains while entering switchdev mode. Instead, on such cases, disable the chains and prio feature (as we can't restore the chain on miss) and the usage of fwd and modify. Fixes: 8f1e0b97 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping") Signed-off-by:
Paul Blakey <paulb@mellanox.com> Reviewed-by:
Oz Shlomo <ozsh@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Nathan Chancellor authored
When CONFIG_MLX5_ESWITCH is unset, clang warns: In file included from drivers/net/ethernet/mellanox/mlx5/core/main.c:58: drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:670:1: warning: unused function 'esw_add_restore_rule' [-Wunused-function] esw_add_restore_rule(struct mlx5_eswitch *esw, u32 tag) ^ 1 warning generated. This stub function is missing inline; add it to suppress the warning. Fixes: 11b717d6 ("net/mlx5: E-Switch, Get reg_c0 value on CQE") Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
- Mar 17, 2020
-
-
Jesper Dangaard Brouer authored
XDP-redirect is broken in this driver sfc. XDP_REDIRECT requires tailroom for skb_shared_info when creating an SKB based on the redirected xdp_frame (both in cpumap and veth). The fix requires some initial explaining. The driver uses RX page-split when possible. It reserves the top 64 bytes in the RX-page for storing dma_addr (struct efx_rx_page_state). It also have the XDP recommended headroom of XDP_PACKET_HEADROOM (256 bytes). As it doesn't reserve any tailroom, it can still fit two standard MTU (1500) frames into one page. The sizeof struct skb_shared_info in 320 bytes. Thus drivers like ixgbe and i40e, reduce their XDP headroom to 192 bytes, which allows them to fit two frames with max 1536 bytes into a 4K page (192+1536+320=2048). The fix is to reduce this drivers headroom to 128 bytes and add the 320 bytes tailroom. This account for reserved top 64 bytes in the page, and still fit two frame in a page for normal MTUs. We must never go below 128 bytes of headroom for XDP, as one cacheline is for xdp_frame area and next cacheline is reserved for metadata area. Fixes: eb9a36be ("sfc: perform XDP processing on received packets") Signed-off-by:
Jesper Dangaard Brouer <brouer@redhat.com> Acked-by:
Edward Cree <ecree@solarflare.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alex Elder authored
Rearrange the config files for remoteproc and IPA to fix their interdependencies. First, have CONFIG_QCOM_Q6V5_MSS select QCOM_Q6V5_IPA_NOTIFY so the notification code is built regardless of whether IPA needs it. Next, represent QCOM_IPA as being dependent on QCOM_Q6V5_MSS rather than setting its value to match QCOM_Q6V5_COMMON (which is selected by QCOM_Q6V5_MSS). Drop all dependencies from QCOM_Q6V5_IPA_NOTIFY. The notification code will be built whenever QCOM_Q6V5_MSS is set, and it has no other dependencies. Signed-off-by:
Alex Elder <elder@linaro.org> Reviewed-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Madhuparna Bhowmik authored
This path fixes the suspicious RCU usage warning reported by kernel test robot. net/kcm/kcmproc.c:#RCU-list_traversed_in_non-reader_section There is no need to use list_for_each_entry_rcu() in kcm_stats_seq_show() as the list is always traversed under knet->mutex held. Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
Madhuparna Bhowmik <madhuparnabhowmik10@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Zheng Zengkai authored
Remove set but not used variables 'sw_comp_cons' and 'hw_comp_cons' to fix gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic: drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:20: warning: variable sw_comp_cons set but not used [-Wunused-but-set-variable] drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function qede_selftest_receive_traffic: drivers/net/ethernet/qlogic/qede/qede_ethtool.c:1569:6: warning: variable hw_comp_cons set but not used [-Wunused-but-set-variable] After removing 'hw_comp_cons',the memory barrier 'rmb()' and its comments become useless, so remove them as well. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Zheng Zengkai <zhengzengkai@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Mar 16, 2020
-
-
Jiri Pirko authored
For a single pedit action, multiple offload entries may be used. Set the hw_stats_type to all of them. Fixes: 44f86580 ("sched: act: allow user to specify type of HW stats for a filter") Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Dejin Zheng says: ==================== net: stmmac: Use readl_poll_timeout() to simplify the code This patch sets just for replace the open-coded loop to the readl_poll_timeout() helper macro for simplify the code in stmmac driver. v2 -> v3: - return whatever error code by readl_poll_timeout() returned. v1 -> v2: - no changed. I am a newbie and sent this patch a month ago (February 6th). So far, I have not received any comments or suggestion. I think it may be lost somewhere in the world, so resend it. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dejin Zheng authored
The dwmac4_dma_reset() function use an open coded of readl_poll_timeout(). Replace the open coded handling with the proper function. Signed-off-by:
Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dejin Zheng authored
The init_systime() function use an open coded of readl_poll_timeout(). Replace the open coded handling with the proper function. Signed-off-by:
Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
YueHaibing authored
drivers/crypto/chelsio/chcr_ktls.c: In function chcr_ktls_cpl_set_tcb_rpl: drivers/crypto/chelsio/chcr_ktls.c:662:11: warning: variable status set but not used [-Wunused-but-set-variable] commit 8a30923e ("cxgb4/chcr: Save tx keys and handle HW response") involved this unused variable, remove it. Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
YueHaibing <yuehaibing@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Era Mayflower authored
Netlink support of extended packet number cipher suites, allows adding and updating XPN macsec interfaces. Added support in: * Creating interfaces with GCM-AES-XPN-128 and GCM-AES-XPN-256 suites. * Setting and getting 64bit packet numbers with of SAs. * Setting (only on SA creation) and getting ssci of SAs. * Setting salt when installing a SAK. Added 2 cipher suite identifiers according to 802.1AE-2018 table 14-1: * MACSEC_CIPHER_ID_GCM_AES_XPN_128 * MACSEC_CIPHER_ID_GCM_AES_XPN_256 In addition, added 2 new netlink attribute types: * MACSEC_SA_ATTR_SSCI * MACSEC_SA_ATTR_SALT Depends on: macsec: Support XPN frame handling - IEEE 802.1AEbw. Signed-off-by:
Era Mayflower <mayflowerera@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Era Mayflower authored
Support extended packet number cipher suites (802.1AEbw) frames handling. This does not include the needed netlink patches. * Added xpn boolean field to `struct macsec_secy`. * Added ssci field to `struct_macsec_tx_sa` (802.1AE figure 10-5). * Added ssci field to `struct_macsec_rx_sa` (802.1AE figure 10-5). * Added salt field to `struct macsec_key` (802.1AE 10.7 NOTE 1). * Created pn_t type for easy access to lower and upper halves. * Created salt_t type for easy access to the "ssci" and "pn" parts. * Created `macsec_fill_iv_xpn` function to create IV in XPN mode. * Support in PN recovery and preliminary replay check in XPN mode. In addition, according to IEEE 802.1AEbw figure 10-5, the PN of incoming frame can be 0 when XPN cipher suite is used, so fixed the function `macsec_validate_skb` to fail on PN=0 only if XPN is off. Signed-off-by:
Era Mayflower <mayflowerera@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Russell King says: ==================== net: dsa: improve serdes integration Depends on "net: mii clause 37 helpers". Andrew Lunn mentioned that the Serdes PCS found in Marvell DSA switches does not automatically update the switch MACs with the link parameters. Currently, the DSA code implements a work-around for this. This series improves the Serdes integration, making use of the recent phylink changes to support split MAC/PCS setups. One noticable improvement for userspace is that ethtool can now report the link partner's advertisement. This repost has no changes compared to the previous posting; however, the regression Andrew had found which exists even without this patch set has now been fixed by Andrew and merged into the net-next tree. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Use the status of the PHY_DETECT bit to determine whether we need to force the MAC settings in mac_link_up() and mac_link_down(). Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
The port_link_state method is only used by mv88e6xxx_port_setup_mac(), which is now only called during port setup, rather than also being called via phylink's mac_config method. Remove this now unnecessary optimisation, which allows us to remove the port_link_state methods as well. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Setting the speed independently of duplex makes little sense; the two parameters result from negotiation or fixed setup, and may have inter- dependencies. Moreover, they are always controlled via the same register - having them split means we have to read-modify-write this register twice. Combine the two operations into a single port_set_speed_duplex() operation. Not only is this more efficient, it reduces the size of the code as well. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
phylink_mac_change() is supposed to be called with a 'false' argument if the link has gone down since it was last reported up; this is to ensure that link events along with renegotiation events are always correctly reported to userspace. Read the BMSR once when we have an interrupt, and report the link latched status to phylink via phylink_mac_change(). phylink will deal automatically with re-reading the link state once it has processed the link-down event. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Extend the mv88e6xxx phylink implementation down to Serdes PHYs, which handle the PCS layer of such links. - Implement phylink PCS link state reading, so that we can provide ethtool with the linkmodes and link speed in the expected manner. Note: this will only be called for in-band negotiation, which is only supported by the serdes interfaces. - Implement phylink PCS configuration, so that the in-band AN and advertisement can be configured. - Implement phylink PCS negotiation restart, so that the in-band AN can be restarted. - Implement phylink PCS link up, so that when operating out-of-band, the Serdes can be configured for the appropriate fixed speed mode. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Only configure the interface settings in mac_config(), leaving the speed and duplex settings to mac_link_up to deal with. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
The SGMII/1000base-X serdes register set is a clause 22 register set offset at 0x2000 in the PHYXS device. Rather than inventing our own defintions, use those that already exist, and name the register MV88E6390_SGMII_BMCR. Also remove the unused MV88E6390_SGMII_STATUS definitions. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Issue a warning to the kernel log if phylink_mac_link_state() returns an error. This should not occur, but let's make it visible. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Russell King says: ==================== net: mii clause 37 helpers This is a re-post of two patches that are common to two series that I've sent in recent weeks; I'm re-posting them separately in the hope that they can be merged. No changes from either of the previous postings. These patches: 1. convert the existing (unused) mii_lpa_to_ethtool_lpa_x() function to a linkmode variant. 2. add a helper for clause 37 advertisements, supporting both the 1000baseX and defacto 2500baseX variants. Note that ethtool does not support half duplex for either of these, and we make no effort to do so. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Add a helper to convert a linkmode advertisement to a clause 37 advertisement value for 1000base-x and 2500base-x. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Russell King authored
Add a LPA to linkmode decoder for 1000BASE-X protocols; this decoder only provides the modify semantics similar to other such decoders. This replaces the unused mii_lpa_to_ethtool_lpa_x() helper. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Mar 15, 2020
-
-
Alexander Bersenev authored
The ndp32->wLength is two bytes long, so replace cpu_to_le32 with cpu_to_le16. Fixes: 0fa81b30 ("cdc_ncm: Implement the 32-bit version of NCM Transfer Block") Signed-off-by:
Alexander Bersenev <bay@hackerdom.ru> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Paolo Abeni says: ==================== mptcp: simplify mptcp_accept() Currently we allocate the MPTCP master socket at accept time. The above makes mptcp_accept() quite complex, and requires checks is several places for NULL MPTCP master socket. These series simplify the MPTCP accept implementation, moving the master socket allocation at syn-ack time, so that we drop unneeded checks with the follow-up patch. v1 -> v2: - rebased on top of 2398e399 ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
After the previous patch subflow->conn is always != NULL and is never changed. We can drop a bunch of now unneeded checks. v1 -> v2: - rebased on top of commit 2398e399 ("mptcp: always include dack if possible.") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
This change moves the mptcp socket allocation from mptcp_accept() to subflow_syn_recv_sock(), so that subflow->conn is now always set for the non fallback scenario. It allows cleaning up a bit mptcp_accept() reducing the additional locking and will allow fourther cleanup in the next patch. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dejin Zheng authored
Use devm_platform_ioremap_resource() to simplify code, which contains platform_get_resource and devm_ioremap_resource. Signed-off-by:
Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Being a non-physical port, the CPU port does not have an ocelot_port structure, so the ocelot_port_writel call inside the ocelot_port_set_maxlen() function would access data behind a NULL pointer. This is a patch for net-next only, the net tree boots fine, the bug was introduced during the net -> net-next merge. Fixes: 1d343579 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net") Fixes: a8015ded ("net: mscc: ocelot: properly account for VLAN header length when setting MRU") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-