- Jun 19, 2021
-
-
Esben Haabendal authored
Just as the initial check, we need to ensure num_frag+1 buffers available, as that is the number of buffers we are going to use. This fixes a buffer overflow, which might be seen during heavy network load. Complete lockup of TEMAC was reproducible within about 10 minutes of a particular load. Fixes: 84823ff8 ("net: ll_temac: Fix race condition causing TX hang") Cc: stable@vger.kernel.org # v5.4+ Signed-off-by:
Esben Haabendal <esben@geanix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Esben Haabendal authored
Add a couple of memory-barriers to ensure correct ordering of read/write access to TX BDs. In xmit_done, we should ensure that reading the additional BD fields are only done after STS_CTRL_APP0_CMPLT bit is set. When xmit_done marks the BD as free by setting APP0=0, we need to ensure that the other BD fields are reset first, so we avoid racing with the xmit path, which writes to the same fields. Finally, making sure to read APP0 of next BD after the current BD, ensures that we see all available buffers. Signed-off-by:
Esben Haabendal <esben@geanix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Esben Haabendal authored
With the skb pointer piggy-backed on the TX BD, we have a simple and efficient way to free the skb buffer when the frame has been transmitted. But in order to avoid freeing the skb while there are still fragments from the skb in use, we need to piggy-back on the TX BD of the skb, not the first. Without this, we are doing use-after-free on the DMA side, when the first BD of a multi TX BD packet is seen as completed in xmit_done, and the remaining BDs are still being processed. Cc: stable@vger.kernel.org # v5.4+ Signed-off-by:
Esben Haabendal <esben@geanix.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Karsten Graul authored
Add Guvenc as maintainer for Shared Memory Communications (SMC) Sockets. Cc: Julian Wiedmann <jwi@linux.ibm.com> Acked-by:
Guvenc Gulce <guvenc@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Bug fixes This patchset includes 3 small bug fixes to reinitialize PHY capabilities after firmware reset, setup the chip's internal TQM fastpath ring backing memory properly for RoCE traffic, and to free ethtool related memory if driver probe fails. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Somnath Kotur authored
bnxt_ethtool_init() may have allocated some memory and we need to call bnxt_ethtool_free() to properly unwind if bnxt_init_one() fails. Fixes: 7c380918 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.") Signed-off-by:
Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Rukhsana Ansari authored
TQM fastpath ring needs to be sized to store both the requester and responder side of RoCE QPs in TQM for supporting bi-directional tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of 2 when computing the number of entries for TQM fastpath ring. This fixes an RX pipeline stall issue when running bi-directional max RoCE QP tests. Fixes: c7dd7ab4 ("bnxt_en: Improve TQM ring context memory sizing formulas.") Signed-off-by:
Rukhsana Ansari <rukhsana.ansari@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Michael Chan authored
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to rediscover the PHY capabilities after a firmware reset. This can cause some PHY related functionalities to fail after a firmware reset. For example, in multi-host, the ability for any host to configure the PHY settings may be lost after a firmware reset. Fixes: ec5d31e3 ("bnxt_en: Handle firmware reset status during IF_UP.") Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Pavel Machek authored
While fixing coverity warning, commit dd2c7967 introduced typo in shift value. Fix that. Signed-off-by:
Pavel Machek (CIP) <pavel@denx.de> Fixes: dd2c7967 ("cxgb4: Fix unintentional sign extension issues") Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Jun 18, 2021
-
-
Kees Cook authored
The source (&dcbx_info->operational.params) and dest (&p_hwfn->p_dcbx_info->set.config.params) are both struct qed_dcbx_params (560 bytes), not struct qed_dcbx_admin_params (564 bytes), which is used as the memcpy() size. However it seems that struct qed_dcbx_operational_params (dcbx_info->operational)'s layout matches struct qed_dcbx_admin_params (p_hwfn->p_dcbx_info->set.config)'s 4 byte difference (3 padding, 1 byte for "valid"). On the assumption that the size is wrong (rather than the source structure type), adjust the memcpy() size argument to be 4 bytes smaller and add a BUILD_BUG_ON() to validate any changes to the structure sizes. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Linyu Yuan authored
when usbnet transmit a skb, eem fixup it in eem_tx_fixup(), if skb_copy_expand() failed, it return NULL, usbnet_start_xmit() will have no chance to free original skb. fix it by free orginal skb in eem_tx_fixup() first, then check skb clone status, if failed, return NULL to usbnet. Fixes: 9f722c09 ("usbnet: CDC EEM support (v5)") Signed-off-by:
Linyu Yuan <linyyuan@codeaurora.org> Reviewed-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5 fixes 2021-06-16 This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Pavel Skripkin authored
My local syzbot instance hit memory leak in mkiss_open()[1]. The problem was in missing free_netdev() in mkiss_close(). In mkiss_open() netdevice is allocated and then registered, but in mkiss_close() netdevice was only unregistered, but not freed. Fail log: BUG: memory leak unreferenced object 0xffff8880281ba000 (size 4096): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): 61 78 30 00 00 00 00 00 00 00 00 00 00 00 00 00 ax0............. 00 27 fa 2a 80 88 ff ff 00 00 00 00 00 00 00 00 .'.*............ backtrace: [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0 [<ffffffff8706e7e8>] alloc_netdev_mqs+0x98/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae BUG: memory leak unreferenced object 0xffff8880141a9a00 (size 96): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): e8 a2 1b 28 80 88 ff ff e8 a2 1b 28 80 88 ff ff ...(.......(.... 98 92 9c aa b0 40 02 00 00 00 00 00 00 00 00 00 .....@.......... backtrace: [<ffffffff8709f68b>] __hw_addr_create_ex+0x5b/0x310 [<ffffffff8709fb38>] __hw_addr_add_ex+0x1f8/0x2b0 [<ffffffff870a0c7b>] dev_addr_init+0x10b/0x1f0 [<ffffffff8706e88b>] alloc_netdev_mqs+0x13b/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae BUG: memory leak unreferenced object 0xffff8880219bfc00 (size 512): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): 00 a0 1b 28 80 88 ff ff 80 8f b1 8d ff ff ff ff ...(............ 80 8f b1 8d ff ff ff ff 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0 [<ffffffff8706eec7>] alloc_netdev_mqs+0x777/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae BUG: memory leak unreferenced object 0xffff888029b2b200 (size 256): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0 [<ffffffff8706f062>] alloc_netdev_mqs+0x912/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: 815f62bf ("[PATCH] SMP rewrite of mkiss") Signed-off-by:
Pavel Skripkin <paskripkin@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Christophe JAILLET authored
If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it must be undone by a corresponding 'pci_disable_pcie_error_reporting()' call, as already done in the remove function. Fixes: d6b6d987 ("be2net: use PCIe AER capability") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Jun 17, 2021
-
-
Aya Levin authored
Reset only the index part of the mkey and keep the variant part. On devlink reload, driver recreates mkeys, so the mkey index may change. Trying to preserve the variant part of the mkey, driver mistakenly merged the mkey index with current value. In case of a devlink reload, current value of index part is dirty, so the index may be corrupted. Fixes: 54c62e13 ("{IB,net}/mlx5: Setup mkey variant before mr create command invocation") Signed-off-by:
Aya Levin <ayal@nvidia.com> Signed-off-by:
Amir Tzin <amirtz@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Dmytro Linkin authored
Running devlink reload command for port in switchdev mode cause resources to corrupt: driver can't release allocated EQ and reclaim memory pages, because "rdma" auxiliary device had add CQs which blocks EQ from deletion. Erroneous sequence happens during reload-down phase, and is following: 1. detach device - suspends auxiliary devices which support it, destroys others. During this step "eth-rep" and "rdma-rep" are destroyed, "eth" - suspended. 2. disable SRIOV - moves device to legacy mode; as part of disablement - rescans drivers. This step adds "rdma" auxiliary device. 3. destroy EQ table - <failure>. Driver shouldn't create any device during unload flows. To handle that implement MLX5_PRIV_FLAGS_DETACH flag, set it on device detach and unset on device attach. If flag is set do no-op on drivers rescan. Fixes: a925b5e3 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus") Signed-off-by:
Dmytro Linkin <dlinkin@nvidia.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Reviewed-by:
Roi Dayan <roid@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Alex Vesker authored
Decapsulation L3 on small inner packets which are less than 64 Bytes was done incorrectly. In small packets there is an extra padding added in L2 which should not be included in L3 length. The issue was that after decapL3 the extra L2 padding caused an update on the L3 length. To avoid this issue the new header is pushed to the beginning of the packet (offset 0) which should not cause a HW reparse and update the L3 length. Fixes: c349b413 ("net/mlx5: DR, Add STEv1 modify header logic") Reviewed-by:
Erez Shitrit <erezsh@nvidia.com> Reviewed-by:
Yevgeny Kliteynik <kliteyn@nvidia.com> Signed-off-by:
Alex Vesker <valex@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Parav Pandit authored
When auxiliary bus autoprobe is disabled and SF is in ACTIVE state, on SF port deletion it transitions from ACTIVE->ALLOCATED->INVALID. When VHCA event handler queries the state, it is already transition to INVALID state. In this scenario, event handler missed to delete the SF device. Fix it by deleting the SF when SF state is INVALID. Fixes: 90d010b8 ("net/mlx5: SF, Add auxiliary device support") Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Vu Pham <vuhuong@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Parav Pandit authored
E-switch should be able to set the GUID of host PF vport. Currently it returns an error. This results in below error when user attempts to configure MAC address of the PF of an external controller. $ devlink port function set pci/0000:03:00.0/196608 \ hw_addr 00:00:00:11:22:33 mlx5_core 0000:03:00.0: mlx5_esw_set_vport_mac_locked:1876:(pid 6715):\ "Failed to set vport 0 node guid, err = -22. RDMA_CM will not function properly for this VF." Check for zero vport is no longer needed. Fixes: 330077d1 ("net/mlx5: E-switch, Supporting setting devlink port function mac address") Signed-off-by:
Yuval Avnery <yuvalav@nvidia.com> Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Bodong Wang <bodong@nvidia.com> Reviewed-by:
Alaa Hleihel <alaa@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Parav Pandit authored
External controller PF's MAC address is not read from the device during vport setup. Fail to read this results in showing all zeros to user while the factory programmed MAC is a valid value. $ devlink port show eth1 -jp { "port": { "pci/0000:03:00.0/196608": { "type": "eth", "netdev": "eth1", "flavour": "pcipf", "controller": 1, "pfnum": 0, "splittable": false, "function": { "hw_addr": "00:00:00:00:00:00" } } } } Hence, read it when enabling a vport. After the fix, $ devlink port show eth1 -jp { "port": { "pci/0000:03:00.0/196608": { "type": "eth", "netdev": "eth1", "flavour": "pcipf", "controller": 1, "pfnum": 0, "splittable": false, "function": { "hw_addr": "98:03:9b:a0:60:11" } } } } Fixes: f099fde1 ("net/mlx5: E-switch, Support querying port function mac address") Signed-off-by:
Bodong Wang <bodong@nvidia.com> Signed-off-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Alaa Hleihel <alaa@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Leon Romanovsky authored
The device can be requested to be attached despite being not probed. This situation is possible if devlink reload races with module removal, and the following kernel panic is an outcome of such race. mlx5_core 0000:00:09.0: firmware version: 4.7.9999 mlx5_core 0000:00:09.0: 0.000 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x255 link) BUG: unable to handle page fault for address: fffffffffffffff0 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 3218067 P4D 3218067 PUD 321a067 PMD 0 Oops: 0000 [#1] SMP KASAN NOPTI CPU: 7 PID: 250 Comm: devlink Not tainted 5.12.0-rc2+ #2836 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 RIP: 0010:mlx5_attach_device+0x80/0x280 [mlx5_core] Code: f8 48 c1 e8 03 42 80 3c 38 00 0f 85 80 01 00 00 48 8b 45 68 48 8d 78 f0 48 89 fe 48 c1 ee 03 42 80 3c 3e 00 0f 85 70 01 00 00 <48> 8b 40 f0 48 85 c0 74 0d 48 89 ef ff d0 85 c0 0f 85 84 05 0e 00 RSP: 0018:ffff8880129675f0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000001 RCX: ffffffff827407f1 RDX: 1ffff110011336cf RSI: 1ffffffffffffffe RDI: fffffffffffffff0 RBP: ffff888008e0c000 R08: 0000000000000008 R09: ffffffffa0662ee7 R10: fffffbfff40cc5dc R11: 0000000000000000 R12: ffff88800ea002e0 R13: ffffed1001d459f7 R14: ffffffffa05ef4f8 R15: dffffc0000000000 FS: 00007f51dfeaf740(0000) GS:ffff88806d5c0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: fffffffffffffff0 CR3: 000000000bc82006 CR4: 0000000000370ea0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: mlx5_load_one+0x117/0x1d0 [mlx5_core] devlink_reload+0x2d5/0x520 ? devlink_remote_reload_actions_performed+0x30/0x30 ? mutex_trylock+0x24b/0x2d0 ? devlink_nl_cmd_reload+0x62b/0x1070 devlink_nl_cmd_reload+0x66d/0x1070 ? devlink_reload+0x520/0x520 ? devlink_nl_pre_doit+0x64/0x4d0 genl_family_rcv_msg_doit+0x1e9/0x2f0 ? mutex_lock_io_nested+0x1130/0x1130 ? genl_family_rcv_msg_attrs_parse.constprop.0+0x240/0x240 ? security_capable+0x51/0x90 genl_rcv_msg+0x27f/0x4a0 ? genl_get_cmd+0x3c0/0x3c0 ? lock_acquire+0x1a9/0x6d0 ? devlink_reload+0x520/0x520 ? lock_release+0x6c0/0x6c0 netlink_rcv_skb+0x11d/0x340 ? genl_get_cmd+0x3c0/0x3c0 ? netlink_ack+0x9f0/0x9f0 ? lock_release+0x1f9/0x6c0 genl_rcv+0x24/0x40 netlink_unicast+0x433/0x700 ? netlink_attachskb+0x730/0x730 ? _copy_from_iter_full+0x178/0x650 ? __alloc_skb+0x113/0x2b0 netlink_sendmsg+0x6f1/0xbd0 ? netlink_unicast+0x700/0x700 ? netlink_unicast+0x700/0x700 sock_sendmsg+0xb0/0xe0 __sys_sendto+0x193/0x240 ? __x64_sys_getpeername+0xb0/0xb0 ? copy_page_range+0x2300/0x2300 ? __up_read+0x1a1/0x7b0 ? do_user_addr_fault+0x219/0xdc0 __x64_sys_sendto+0xdd/0x1b0 ? syscall_enter_from_user_mode+0x1d/0x50 do_syscall_64+0x2d/0x40 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f51dffb514a Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 76 c3 0f 1f 44 00 00 55 48 83 ec 30 44 89 4c RSP: 002b:00007ffcaef22e78 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00007f51dffb514a RDX: 0000000000000030 RSI: 000055750daf2440 RDI: 0000000000000003 RBP: 000055750daf2410 R08: 00007f51e0081200 R09: 000000000000000c R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 Modules linked in: mlx5_core(-) ptp pps_core ib_ipoib rdma_ucm rdma_cm iw_cm ib_cm ib_umad ib_uverbs ib_core [last unloaded: mlx5_ib] CR2: fffffffffffffff0 ---[ end trace 7789831bfe74fa42 ]--- Fixes: a925b5e3 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus") Signed-off-by:
Leon Romanovsky <leonro@nvidia.com> Reviewed-by:
Parav Pandit <parav@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Leon Romanovsky authored
In the case of the failure to execute mlx5_core_set_hca_defaults(), we used wrong goto label to execute error unwind flow. Fixes: 5bef709d ("net/mlx5: Enable host PF HCA after eswitch is initialized") Reviewed-by:
Saeed Mahameed <saeedm@nvidia.com> Reviewed-by:
Moshe Shemesh <moshe@nvidia.com> Signed-off-by:
Leon Romanovsky <leonro@nvidia.com> Reviewed-by:
Parav Pandit <parav@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com>
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally reading across neighboring array fields. The memcpy() is copying the entire structure, not just the first array. Adjust the source argument so the compiler can do appropriate bounds checking. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally reading across neighboring array fields. The memcpy() is copying the entire structure, not just the first array. Adjust the source argument so the compiler can do appropriate bounds checking. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kees Cook authored
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memcpy(), memmove(), and memset(), avoid intentionally reading across neighboring array fields. The memcpy() is copying the entire structure, not just the first array. Adjust the source argument so the compiler can do appropriate bounds checking. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrea Righi authored
udpgro_fwd.sh contains many bash specific operators ("[[", "local -r"), but it's using /bin/sh; in some distro /bin/sh is mapped to /bin/dash, that doesn't support such operators. Force the test to use /bin/bash explicitly and prevent false positive test failures. Signed-off-by:
Andrea Righi <andrea.righi@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
While unix_may_send(sk, osk) is called while osk is locked, it appears unix_release_sock() can overwrite unix_peer() after this lock has been released, making KCSAN unhappy. Changing unix_release_sock() to access/change unix_peer() before lock is released should fix this issue. BUG: KCSAN: data-race in unix_dgram_sendmsg / unix_release_sock write to 0xffff88810465a338 of 8 bytes by task 20852 on cpu 1: unix_release_sock+0x4ed/0x6e0 net/unix/af_unix.c:558 unix_release+0x2f/0x50 net/unix/af_unix.c:859 __sock_release net/socket.c:599 [inline] sock_close+0x6c/0x150 net/socket.c:1258 __fput+0x25b/0x4e0 fs/file_table.c:280 ____fput+0x11/0x20 fs/file_table.c:313 task_work_run+0xae/0x130 kernel/task_work.c:164 tracehook_notify_resume include/linux/tracehook.h:189 [inline] exit_to_user_mode_loop kernel/entry/common.c:175 [inline] exit_to_user_mode_prepare+0x156/0x190 kernel/entry/common.c:209 __syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline] syscall_exit_to_user_mode+0x20/0x40 kernel/entry/common.c:302 do_syscall_64+0x56/0x90 arch/x86/entry/common.c:57 entry_SYSCALL_64_after_hwframe+0x44/0xae read to 0xffff88810465a338 of 8 bytes by task 20888 on cpu 0: unix_may_send net/unix/af_unix.c:189 [inline] unix_dgram_sendmsg+0x923/0x1610 net/unix/af_unix.c:1712 sock_sendmsg_nosec net/socket.c:654 [inline] sock_sendmsg net/socket.c:674 [inline] ____sys_sendmsg+0x360/0x4d0 net/socket.c:2350 ___sys_sendmsg net/socket.c:2404 [inline] __sys_sendmmsg+0x315/0x4b0 net/socket.c:2490 __do_sys_sendmmsg net/socket.c:2519 [inline] __se_sys_sendmmsg net/socket.c:2516 [inline] __x64_sys_sendmmsg+0x53/0x60 net/socket.c:2516 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0xffff888167905400 -> 0x0000000000000000 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 20888 Comm: syz-executor.0 Not tainted 5.13.0-rc5-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andrea Righi authored
veth.sh is a shell script that uses /bin/sh; some distro (Ubuntu for example) use dash as /bin/sh and in this case the test reports the following error: # ./veth.sh: 21: local: -r: bad variable name # ./veth.sh: 21: local: -r: bad variable name This happens because dash doesn't support the option "-r" with local. Moreover, in case of missing bpf object, the script is exiting -1, that is an illegal number for dash: exit: Illegal number: -1 Change the script to be compatible both with bash and dash and prevent the errors above. Signed-off-by:
Andrea Righi <andrea.righi@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Eric Dumazet says: ==================== net/packet: annotate data races KCSAN sent two reports about data races in af_packet. Nothing serious, but worth fixing. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Like prior patch, we need to annotate lockless accesses to po->ifindex For instance, packet_getname() is reading po->ifindex (twice) while another thread is able to change po->ifindex. KCSAN reported: BUG: KCSAN: data-race in packet_do_bind / packet_getname write to 0xffff888143ce3cbc of 4 bytes by task 25573 on cpu 1: packet_do_bind+0x420/0x7e0 net/packet/af_packet.c:3191 packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255 __sys_bind+0x200/0x290 net/socket.c:1637 __do_sys_bind net/socket.c:1648 [inline] __se_sys_bind net/socket.c:1646 [inline] __x64_sys_bind+0x3d/0x50 net/socket.c:1646 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47 entry_SYSCALL_64_after_hwframe+0x44/0xae read to 0xffff888143ce3cbc of 4 bytes by task 25578 on cpu 0: packet_getname+0x5b/0x1a0 net/packet/af_packet.c:3525 __sys_getsockname+0x10e/0x1a0 net/socket.c:1887 __do_sys_getsockname net/socket.c:1902 [inline] __se_sys_getsockname net/socket.c:1899 [inline] __x64_sys_getsockname+0x3e/0x50 net/socket.c:1899 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0x00000000 -> 0x00000001 Reported by Kernel Concurrency Sanitizer on: CPU: 0 PID: 25578 Comm: syz-executor.5 Not tainted 5.13.0-rc6-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
tpacket_snd(), packet_snd(), packet_getname() and packet_seq_show() can read po->num without holding a lock. This means other threads can change po->num at the same time. KCSAN complained about this known fact [1] Add READ_ONCE()/WRITE_ONCE() to address the issue. [1] BUG: KCSAN: data-race in packet_do_bind / packet_sendmsg write to 0xffff888131a0dcc0 of 2 bytes by task 24714 on cpu 0: packet_do_bind+0x3ab/0x7e0 net/packet/af_packet.c:3181 packet_bind+0xc3/0xd0 net/packet/af_packet.c:3255 __sys_bind+0x200/0x290 net/socket.c:1637 __do_sys_bind net/socket.c:1648 [inline] __se_sys_bind net/socket.c:1646 [inline] __x64_sys_bind+0x3d/0x50 net/socket.c:1646 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47 entry_SYSCALL_64_after_hwframe+0x44/0xae read to 0xffff888131a0dcc0 of 2 bytes by task 24719 on cpu 1: packet_snd net/packet/af_packet.c:2899 [inline] packet_sendmsg+0x317/0x3570 net/packet/af_packet.c:3040 sock_sendmsg_nosec net/socket.c:654 [inline] sock_sendmsg net/socket.c:674 [inline] ____sys_sendmsg+0x360/0x4d0 net/socket.c:2350 ___sys_sendmsg net/socket.c:2404 [inline] __sys_sendmsg+0x1ed/0x270 net/socket.c:2433 __do_sys_sendmsg net/socket.c:2442 [inline] __se_sys_sendmsg net/socket.c:2440 [inline] __x64_sys_sendmsg+0x42/0x50 net/socket.c:2440 do_syscall_64+0x4a/0x90 arch/x86/entry/common.c:47 entry_SYSCALL_64_after_hwframe+0x44/0xae value changed: 0x0000 -> 0x1200 Reported by Kernel Concurrency Sanitizer on: CPU: 1 PID: 24719 Comm: syz-executor.5 Not tainted 5.13.0-rc4-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'linux-can-fixes-for-5.13-20210616' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can Marc Kleine-Budde says: ==================== pull-request: can 2021-06-16 this is a pull request of 4 patches for net/master. The first patch is by Oleksij Rempel and fixes a Use-after-Free found by syzbot in the j1939 stack. The next patch is by Tetsuo Handa and fixes hung task detected by syzbot in the bcm, raw and isotp protocols. Norbert Slusarek's patch fixes a infoleak in bcm's struct bcm_msg_head. Pavel Skripkin's patch fixes a memory leak in the mcba_usb driver. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Chengyang Fan authored
BUG: memory leak unreferenced object 0xffff888101bc4c00 (size 32): comm "syz-executor527", pid 360, jiffies 4294807421 (age 19.329s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 01 00 00 00 00 00 00 00 ac 14 14 bb 00 00 02 00 ................ backtrace: [<00000000f17c5244>] kmalloc include/linux/slab.h:558 [inline] [<00000000f17c5244>] kzalloc include/linux/slab.h:688 [inline] [<00000000f17c5244>] ip_mc_add1_src net/ipv4/igmp.c:1971 [inline] [<00000000f17c5244>] ip_mc_add_src+0x95f/0xdb0 net/ipv4/igmp.c:2095 [<000000001cb99709>] ip_mc_source+0x84c/0xea0 net/ipv4/igmp.c:2416 [<0000000052cf19ed>] do_ip_setsockopt net/ipv4/ip_sockglue.c:1294 [inline] [<0000000052cf19ed>] ip_setsockopt+0x114b/0x30c0 net/ipv4/ip_sockglue.c:1423 [<00000000477edfbc>] raw_setsockopt+0x13d/0x170 net/ipv4/raw.c:857 [<00000000e75ca9bb>] __sys_setsockopt+0x158/0x270 net/socket.c:2117 [<00000000bdb993a8>] __do_sys_setsockopt net/socket.c:2128 [inline] [<00000000bdb993a8>] __se_sys_setsockopt net/socket.c:2125 [inline] [<00000000bdb993a8>] __x64_sys_setsockopt+0xba/0x150 net/socket.c:2125 [<000000006a1ffdbd>] do_syscall_64+0x40/0x80 arch/x86/entry/common.c:47 [<00000000b11467c4>] entry_SYSCALL_64_after_hwframe+0x44/0xae In commit 24803f38 ("igmp: do not remove igmp souce list info when set link down"), the ip_mc_clear_src() in ip_mc_destroy_dev() was removed, because it was also called in igmpv3_clear_delrec(). Rough callgraph: inetdev_destroy -> ip_mc_destroy_dev -> igmpv3_clear_delrec -> ip_mc_clear_src -> RCU_INIT_POINTER(dev->ip_ptr, NULL) However, ip_mc_clear_src() called in igmpv3_clear_delrec() doesn't release in_dev->mc_list->sources. And RCU_INIT_POINTER() assigns the NULL to dev->ip_ptr. As a result, in_dev cannot be obtained through inetdev_by_index() and then in_dev->mc_list->sources cannot be released by ip_mc_del1_src() in the sock_close. Rough call sequence goes like: sock_close -> __sock_release -> inet_release -> ip_mc_drop_socket -> inetdev_by_index -> ip_mc_leave_src -> ip_mc_del_src -> ip_mc_del1_src So we still need to call ip_mc_clear_src() in ip_mc_destroy_dev() to free in_dev->mc_list->sources. Fixes: 24803f38 ("igmp: do not remove igmp souce list info ...") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Chengyang Fan <cy.fan@huawei.com> Acked-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Joakim Zhang says: ==================== net: fixes for fec ptp Small fixes for fec ptp. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
Commit da722186 ("net: fec: set GPR bit on suspend by DT configuration.") refactor the fec_devtype, need adjust ptp driver accordingly. Fixes: da722186 ("net: fec: set GPR bit on suspend by DT configuration.") Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Fugang Duan authored
Add clock rate zero check to fix coverity issue of "divide by 0". Fixes: commit 85bd1798 ("net: fec: fix spin_lock dead lock") Signed-off-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dongliang Mu authored
The commit 46a8b29c ("net: usb: fix memory leak in smsc75xx_bind") fails to clean up the work scheduled in smsc75xx_reset-> smsc75xx_set_multicast, which leads to use-after-free if the work is scheduled to start after the deallocation. In addition, this patch also removes a dangling pointer - dev->data[0]. This patch calls cancel_work_sync to cancel the scheduled work and set the dangling pointer to NULL. Fixes: 46a8b29c ("net: usb: fix memory leak in smsc75xx_bind") Signed-off-by:
Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Joakim Zhang authored
Platform drivers may call stmmac_probe_config_dt() to parse dt, could call stmmac_remove_config_dt() in error handing after dt parsed, so need disable clocks in stmmac_remove_config_dt(). Go through all platforms drivers which use stmmac_probe_config_dt(), none of them disable clocks manually, so it's safe to disable them in stmmac_remove_config_dt(). Fixes: commit d2ed0a77 ("net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks") Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Jun 16, 2021
-
-
Pavel Skripkin authored
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS Analyzer Tool. The problem was in unfreed usb_coherent. In mcba_usb_start() 20 coherent buffers are allocated and there is nothing, that frees them: 1) In callback function the urb is resubmitted and that's all 2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER is not set (see mcba_usb_start) and this flag cannot be used with coherent buffers. Fail log: | [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected | [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem) So, all allocated buffers should be freed with usb_free_coherent() explicitly NOTE: The same pattern for allocating and freeing coherent buffers is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c Fixes: 51f3baad ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Reported-and-tested-by:
<syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com> Signed-off-by:
Pavel Skripkin <paskripkin@gmail.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Norbert Slusarek authored
On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between struct members count and ival1. Even though all struct members are initialized, the 4-byte hole will contain data from the kernel stack. This patch zeroes out struct bcm_msg_head before usage, preventing infoleaks to userspace. Fixes: ffd980f9 ("[CAN]: Add broadcast manager (bcm) protocol") Link: https://lore.kernel.org/r/trinity-7c1b2e82-e34f-4885-8060-2cd7a13769ce-1623532166177@3c-app-gmx-bs52 Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Norbert Slusarek <nslusarek@gmx.net> Acked-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-