Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In programmable mode, if the clock frequency is too high, the divider
can be too small to meet the clock frequency requirement especially to
init the SD card. In this case, switch to the divided clock mode.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch add a new quirk to add a s/w timer to notify the driver
to terminate current transfer and report a data timeout to the core,
if DTO interrupt does NOT come within the given time.

dw_mmc call mmc_request_done func to finish transfer depends on
DTO interrupt. If DTO interrupt does not come in sending data state,
the current transfer will be blocked.

We got the reply from synopsys:
There are two counters but both use the same value of [31:8] bits.
Data timeout counter doesn't wait for stop clock and you should get
DRTO even when the clock is not stopped.
Host Starvation timeout counter is triggered with stop clock condition.

This means that host should get DRTO and DTO interrupt.

But this case really exists, when driver reads tuning data from
card on RK3288-pink2 board. I measured waveforms by oscilloscope
and found that card clock was always on and data lines were always
holded high level in sending data state.

There are two possibility that data over interrupt doesn't come in
reading data state on RK3X SoCs:
- get command done interrupt, but doesn't get any data-related interrupt.
- get data error interrupt, but doesn't get data over interrupt.

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

supports-highspeed was deprecated.
If someone use it, we need to notice information for it.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

"blk_setting" doesn't use anywhere.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

When num-slots is lower than 1, it's right that should be returned -ENODEV.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

The dw_mci_init_dma() may decide to not use dma, but pio instead, caused
by things like wrong dma settings in the system.

Till now the code dw_mci_init_slot() always assumed that dma is available
when CONFIG_MMC_DW_IDMAC was defined, ignoring the host->use_dma var
set during dma init.

So when now the dma init failed for whatever reason, the transfer sizes
would still be set for dma transfers, especially including the maximum
block-count calculated from host->ring_size and resulting in a

[    4.991109] ------------[ cut here ]------------
[    4.991111] kernel BUG at drivers/mmc/core/core.c:256!
[    4.991113] Internal error: Oops - BUG: 0 [#1] SMP ARM

because host->ring_size is 0 in this case and the slot init code uses
the wrong code to calculate the values.

Fix this by selecting the correct calculations using the host->use_dma
variable instead of the CONFIG_MMC_DW_IDMAC config option.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

This patch fixes the following issues reported by checkpatch.pl:
- use -EINVAL instead of -ENOSYS, to fix warning message:
   "ENOSYS means 'invalid syscall nr' and nothing else"
- split lines whose length is greater than 80 characters
- avoid quoted string split across lines
- use min_t instead of min, to fix warning message:
   "min() should probably be min_t(int, cnt, host->part_buf_count)"
- fix missing a blank line after declarations

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.

On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.

In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.

Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.

What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>

Some Sandisk cards(such as "SDMB-32" and "SDM032" cards)
can't support CMD23, and would generate CMD timeout. So add
FIX-UP for these two types Sandisk cards.

Error log:
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
end_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on device mmcblk0, logical block 0
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

eSDHC supports high speed mode, but has no enabling bit for it.
Add this quirk to avoid writing to eSDHC_PROCTL[DTW] by mistake.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For Freescale QorIQ LS1021AQDS board, there is a SDIO interrupt
in the process of resume without inserting SD adapter because of
some unknown issue. But the driver doesn't assign sdio_irq_thread
pointer. This will block the resume of kernel. This patch is used
to avoid using NULL sdio_irq_thread pointer.

Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If no pdata.set_power was set by the platform code, the driver
was updating pdata with its own fallback function. This is a no-no
since pdata shall be read-only.
This patch pushes the check 'pdata->set_power != NULL' down into
the fallback functions. If pdata.set_power is really set, it calls them
and exits, otherwise the fallback code is used.

Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Before 5b83b223

 the driver was hard coding the wakeup irq to
be active low. The generic pm wakeirq does not override the active
high/low parameter, hence it must be specified correctly in the
device tree.
Mind that SDIO IRQ is active low as defined in the SDIO specification

Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Controller could have both NO_CARD_NO_RESET and BROKEN_CARD_DETECTION
quirks set. Use sdhci_do_get_cd() when applying NO_CARD_NO_RESET, which
properly check for BROKEN_CARD_DETECTION quirk.

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is no reason to use polling for card detection state change when
drivers are using dedicated GPIO for this. Don't poll in this case.

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Controller could have BROKEN_CARD_DETECTION quirk set, but drivers
could use GPIO to detect card present state. Let, when defined, GPIO
take precedence, so drivers could properly detect card state and not
use polling.

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.

Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's excessive to use prefix for the parameters when you do
modprobe mmc-block mmcblk.perdev_minors=16

Make this available only for built-in case.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

See Documentation/DMA-API.txt - Part Id

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

adding SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,SDHCI_QUIRK2_PRESET_VALUE_BROKEN
flags for arasan sdhc.

Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

adds quirk for controllers whose clock divider zero is broken,
sdhci_set_clock function will incorporate this modification.

Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Switch over pxamci to dmaengine. This prepares the devicetree full
support of pxamci.

This was successfully tested on a PXA3xx board, as well as PXA27x.

Signed-off-by: Daniel Mack <zonque@gmail.com>
[adapted to pxa-dma]
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In the (not so unlikely) case that the mmc controller timeout budget is
enough for exactly one erase-group, the simplification of allowing one
sector has an enormous performance penalty. We optimize this special case
by introducing a flag that prohibits erase-group boundary crossing, so
that we can allow trimming more than one sector at a time.

Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "A smallish batch of fixes, a little more than expected this late, but
  all fixes are contained to their platforms and seem reasonably low
  risk:

   - a somewhat large SMP fix for ux500 that still seemed warranted to
     include here
   - OMAP DT fixes for pbias regulator specification that broke due to
     some DT reshuffling
   - PCIe IRQ routing bugfix for i.MX
   - networking fixes for keystone
   - runtime PM for OMAP GPMC
   - a couple of error path bug fixes for exynos"

* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
  ARM: dts: keystone: fix the clock node for mdio
  memory: omap-gpmc: Don't try to save uninitialized GPMC context
  ARM: imx6: correct i.MX6 PCIe interrupt routing
  ARM: ux500: add an SMP enablement type and move cpu nodes
  ARM: dts: dra7: Fix broken pbias device creation
  ARM: dts: OMAP5: Fix broken pbias device creation
  ARM: dts: OMAP4: Fix broken pbias device creation
  ARM: dts: omap243x: Fix broken pbias device creation
  ARM: EXYNOS: fix double of_node_put() on error path
  ARM: EXYNOS: Fix potentian kfree() of ro memory

Pull MIPS bugfix from Ralf Baechle:
 "Only a single MIPS fix - the math when invoking syscall_trace_enter
  was wrong"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Fix seccomp syscall argument for MIPS64

Merge x86 fixes from Ingo Molnar:
 "Two followup fixes related to the previous LDT fix"

Also applied a further FPU emulation fix from Andy Lutomirski to the
branch before actually merging it.

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
  x86/ldt: Further fix FPU emulation
  x86/ldt: Correct FPU emulation access to LDT
  x86/ldt: Correct LDT access in single stepping logic

The previous fix confused a selector with a segment prefix.  Fix it.

Compile-tested only.

Cc: stable@vger.kernel.org
Cc: Juergen Gross <jgross@suse.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: 4809146b

 ("x86/ldt: Correct FPU emulation access to LDT")
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

fuse_dev_ioctl() performed fuse_get_dev() on a user-supplied fd,
leading to a type confusion issue. Fix it by checking file->f_op.

Signed-off-by: Jann Horn <jann@thejh.net>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes

ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+

These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are broken without these two fixes.

* tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
  ARM: dts: keystone: fix the clock node for mdio

Signed-off-by: Olof Johansson <olof@lixom.net>

Commit 4c21b8fd ("MIPS: seccomp: Handle indirect system calls (o32)")
fixed indirect system calls on O32 but it also introduced a bug for MIPS64
where it erroneously modified the v0 (syscall) register with the assumption
that the sycall offset hasn't been taken into consideration. This breaks
seccomp on MIPS64 n64 and n32 ABIs. We fix this by replacing the addition
with a move instruction.

Fixes: 4c21b8fd

 ("MIPS: seccomp: Handle indirect system calls (o32)")
Cc: <stable@vger.kernel.org> # 3.15+
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/10951/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull SCSI fixes from James Bottomley:
 "This has two libfc fixes for bugs causing rare crashes, one iscsi fix
  for a potential hang on shutdown, and a fix for an I/O blocksize issue
  which caused a regression"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  sd: Fix maximum I/O size for BLOCK_PC requests
  libfc: Fix fc_fcp_cleanup_each_cmd()
  libfc: Fix fc_exch_recv_req() error path
  libiscsi: Fix host busy blocking during connection teardown

Pull KVM fixes from Paolo Bonzini:
 "Just two very small & simple patches"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Use adjustment in guest cycles when handling MSR_IA32_TSC_ADJUST
  KVM: x86: zero IDT limit on entry to SMM

Merge fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  Update maintainers for DRM STI driver
  mm: cma: mark cma_bitmap_maxno() inline in header
  zram: fix pool name truncation
  memory-hotplug: fix wrong edge when hot add a new node
  .mailmap: Andrey Ryabinin has moved
  ipc/sem.c: update/correct memory barriers
  mm/hwpoison: fix panic due to split huge zero page
  ipc,sem: remove uneeded sem_undo_list lock usage in exit_sem()
  ipc,sem: fix use after free on IPC_RMID after a task using same semaphore set exits
  mm/hwpoison: fix fail isolate hugetlbfs page w/ refcount held
  mm/hwpoison: fix page refcount of unknown non LRU page

Pull clock fix from Stephen Boyd:
 "A one-liner for a regression found in the PXA clock driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: pxa: pxa3xx: fix CKEN register access

Add Vincent Abriou and myself as maintainers.

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

cma_bitmap_maxno() was marked as static and not static inline, which can
cause warnings about this function not being used if this file is included
in a file that does not call that function, and violates the conventions
used elsewhere.  The two options are to move the function implementation
back to mm/cma.c or make it inline here, and it's simple enough for the
latter to make sense.

Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zram_meta_alloc() constructs a pool name for zs_create_pool() call as

    snprintf(pool_name, sizeof(pool_name), "zram%d", device_id);

However, it defines pool name buffer to be only 8 bytes long (minus
trailing zero), which means that we can have only 1000 pool names: zram0
-- zram999.

With CONFIG_ZSMALLOC_STAT enabled an attempt to create a device zram1000
can fail if device zram100 already exists, because snprintf() will
truncate new pool name to zram100 and pass it debugfs_create_dir(),
causing:

  debugfs dir <zram100> creation failed
  zram: Error creating memory pool

... and so on.

Fix it by passing zram->disk->disk_name to zram_meta_alloc() instead of
divice_id.  We construct zram%d name earlier and keep it as a ->disk_name,
no need to snprintf() it again.

Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>