- Dec 01, 2021
-
-
Florian Fainelli authored
[ Upstream commit 754c4050 ] The I2C interrupt controller line is off by 32 because the datasheet describes interrupt inputs into the GIC which are for Shared Peripheral Interrupts and are starting at offset 32. The ARM GIC binding expects the SPI interrupts to be numbered from 0 relative to the SPI base. Fixes: bb097e3e ("ARM: dts: BCM5301X: Add I2C support to the DT") Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Will Mortensen authored
[ Upstream commit 39f6eed4 ] Previously the IPv6 addresses in the key were clobbered and the mask was left unset. I haven't tested this; I noticed it while skimming the code to understand an unrelated issue. Fixes: cfab6dbd ("netfilter: flowtable: add tunnel match offload support") Cc: wenxu <wenxu@ucloud.cn> Signed-off-by: Will Mortensen <willmo@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
yangxingwu authored
[ Upstream commit c95c0783 ] We are changing expire_nodest_conn to work even for reused connections when conn_reuse_mode=0, just as what was done with commit dc7b3eb9 ("ipvs: Fix reuse connection if real server is dead"). For controlled and persistent connections, the new connection will get the needed real server depending on the rules in ip_vs_check_template(). Fixes: d752c364 ("ipvs: allow rescheduling of new connections when port reuse is detected") Co-developed-by: Chuanqi Liu <legend050709@qq.com> Signed-off-by: Chuanqi Liu <legend050709@qq.com> Signed-off-by: yangxingwu <xingwu.yang@gmail.com> Acked-by: Simon Horman <horms@verge.net.au> Acked-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Florent Fourcot authored
[ Upstream commit 77522ff0 ] And be consistent in error management for both orig/reply filtering Fixes: cb8aa9a3 ("netfilter: ctnetlink: add kernel side filtering for dump") Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Florent Fourcot authored
[ Upstream commit ad81d4da ] filter->orig_flags was used for a reply context. Fixes: cb8aa9a3 ("netfilter: ctnetlink: add kernel side filtering for dump") Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
David Hildenbrand authored
commit c1e63117 upstream. To clear a user buffer we cannot simply use memset, we have to use clear_user(). With a virtio-mem device that registers a vmcore_cb and has some logically unplugged memory inside an added Linux memory block, I can easily trigger a BUG by copying the vmcore via "cp": systemd[1]: Starting Kdump Vmcore Save Service... kdump[420]: Kdump is using the default log level(3). kdump[453]: saving to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/ kdump[458]: saving vmcore-dmesg.txt to /sysroot/var/crash/127.0.0.1-2021-11-11-14:59:22/ kdump[465]: saving vmcore-dmesg.txt complete kdump[467]: saving vmcore BUG: unable to handle page fault for address: 00007f2374e01000 #PF: supervisor write access in kernel mode #PF: error_code(0x0003) - permissions violation PGD 7a523067 P4D 7a523067 PUD 7a528067 PMD 7a525067 PTE 800000007048f867 Oops: 0003 [#1] PREEMPT SMP NOPTI CPU: 0 PID: 468 Comm: cp Not tainted 5.15.0+ #6 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.14.0-27-g64f37cc530f1-prebuilt.qemu.org 04/01/2014 RIP: 0010:read_from_oldmem.part.0.cold+0x1d/0x86 Code: ff ff ff e8 05 ff fe ff e9 b9 e9 7f ff 48 89 de 48 c7 c7 38 3b 60 82 e8 f1 fe fe ff 83 fd 08 72 3c 49 8d 7d 08 4c 89 e9 89 e8 <49> c7 45 00 00 00 00 00 49 c7 44 05 f8 00 00 00 00 48 83 e7 f81 RSP: 0018:ffffc9000073be08 EFLAGS: 00010212 RAX: 0000000000001000 RBX: 00000000002fd000 RCX: 00007f2374e01000 RDX: 0000000000000001 RSI: 00000000ffffdfff RDI: 00007f2374e01008 RBP: 0000000000001000 R08: 0000000000000000 R09: ffffc9000073bc50 R10: ffffc9000073bc48 R11: ffffffff829461a8 R12: 000000000000f000 R13: 00007f2374e01000 R14: 0000000000000000 R15: ffff88807bd421e8 FS: 00007f2374e12140(0000) GS:ffff88807f000000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f2374e01000 CR3: 000000007a4aa000 CR4: 0000000000350eb0 Call Trace: read_vmcore+0x236/0x2c0 proc_reg_read+0x55/0xa0 vfs_read+0x95/0x190 ksys_read+0x4f/0xc0 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae Some x86-64 CPUs have a CPU feature called "Supervisor Mode Access Prevention (SMAP)", which is used to detect wrong access from the kernel to user buffers like this: SMAP triggers a permissions violation on wrong access. In the x86-64 variant of clear_user(), SMAP is properly handled via clac()+stac(). To fix, properly use clear_user() when we're dealing with a user buffer. Link: https://lkml.kernel.org/r/20211112092750.6921-1-david@redhat.com Fixes: 997c136f ("fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages") Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Philipp Rudo <prudo@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pali Rohár authored
commit f76b36d4 upstream. Fix multiple link training issues in aardvark driver. The main reason of these issues was misunderstanding of what certain registers do, since their names and comments were misleading: before commit 96be36db ("PCI: aardvark: Replace custom macros by standard linux/pci_regs.h macros"), the pci-aardvark.c driver used custom macros for accessing standard PCIe Root Bridge registers, and misleading comments did not help to understand what the code was really doing. After doing more tests and experiments I've come to the conclusion that the SPEED_GEN register in aardvark sets the PCIe revision / generation compliance and forces maximal link speed. Both GEN3 and GEN2 values set the read-only PCI_EXP_FLAGS_VERS bits (PCIe capabilities version of Root Bridge) to value 2, while GEN1 value sets PCI_EXP_FLAGS_VERS to 1, which matches with PCI Express specifications revisions 3, 2 and 1 respectively. Changing SPEED_GEN also sets the read-only bits PCI_EXP_LNKCAP_SLS and PCI_EXP_LNKCAP2_SLS to corresponding speed. (Note that PCI Express rev 1 specification does not define PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers and when SPEED_GEN is set to GEN1 (which also sets PCI_EXP_FLAGS_VERS set to 1), lspci cannot access PCI_EXP_LNKCAP2 and PCI_EXP_LNKCTL2 registers.) Changing PCIe link speed can be done via PCI_EXP_LNKCTL2_TLS bits of PCI_EXP_LNKCTL2 register. Armada 3700 Functional Specifications says that the default value of PCI_EXP_LNKCTL2_TLS is based on SPEED_GEN value, but tests showed that the default value is always 8.0 GT/s, independently of speed set by SPEED_GEN. So after setting SPEED_GEN, we must also set value in PCI_EXP_LNKCTL2 register via PCI_EXP_LNKCTL2_TLS bits. Triggering PCI_EXP_LNKCTL_RL bit immediately after setting LINK_TRAINING_EN bit actually doesn't do anything. Tests have shown that a delay is needed after enabling LINK_TRAINING_EN bit. As triggering PCI_EXP_LNKCTL_RL currently does nothing, remove it. Commit 43fc679c ("PCI: aardvark: Improve link training") introduced code which sets SPEED_GEN register based on negotiated link speed from PCI_EXP_LNKSTA_CLS bits of PCI_EXP_LNKSTA register. This code was added to fix detection of Compex WLE900VX (Atheros QCA9880) WiFi GEN1 PCIe cards, as otherwise these cards were "invisible" on PCIe bus (probably because they crashed). But apparently more people reported the same issues with these cards also with other PCIe controllers [1] and I was able to reproduce this issue also with other "noname" WiFi cards based on Atheros QCA9890 chip (with the same PCI vendor/device ids as Atheros QCA9880). So this is not an issue in aardvark but rather an issue in Atheros QCA98xx chips. Also, this issue only exists if the kernel is compiled with PCIe ASPM support, and a generic workaround for this is to change PCIe Bridge to 2.5 GT/s link speed via PCI_EXP_LNKCTL2_TLS_2_5GT bits in PCI_EXP_LNKCTL2 register [2], before triggering PCI_EXP_LNKCTL_RL bit. This workaround also works when SPEED_GEN is set to value GEN2 (5 GT/s). So remove this hack completely in the aardvark driver and always set SPEED_GEN to value from 'max-link-speed' DT property. Fix for Atheros QCA98xx chips is handled separately by patch [2]. These two things (code for triggering PCI_EXP_LNKCTL_RL bit and changing SPEED_GEN value) also explain why commit 69644945 ("PCI: aardvark: Train link immediately after enabling training") somehow fixed detection of those problematic Compex cards with Atheros chips: if triggering link retraining (via PCI_EXP_LNKCTL_RL bit) was done immediately after enabling link training (via LINK_TRAINING_EN), it did nothing. If there was a specific delay, aardvark HW already initialized PCIe link and therefore triggering link retraining caused the above issue. Compex cards triggered link down event and disappeared from the PCIe bus. Commit f4c7d053 ("PCI: aardvark: Wait for endpoint to be ready before training link") added 100ms sleep before calling 'Start link training' command and explained that it is a requirement of PCI Express specification. But the code after this 100ms sleep was not doing 'Start link training', rather it triggered PCI_EXP_LNKCTL_RL bit via PCIe Root Bridge to put link into Recovery state. The required delay after fundamental reset is already done in function advk_pcie_wait_for_link() which also checks whether PCIe link is up. So after removing the code which triggers PCI_EXP_LNKCTL_RL bit on PCIe Root Bridge, there is no need to wait 100ms again. Remove the extra msleep() call and update comment about the delay required by the PCI Express specification. According to Marvell Armada 3700 Functional Specifications, Link training should be enabled via aardvark register LINK_TRAINING_EN after selecting PCIe generation and x1 lane. There is no need to disable it prior resetting card via PERST# signal. This disabling code was introduced in commit 5169a985 ("PCI: aardvark: Issue PERST via GPIO") as a workaround for some Atheros cards. It turns out that this also is Atheros specific issue and affects any PCIe controller, not only aardvark. Moreover this Atheros issue was triggered by juggling with PCI_EXP_LNKCTL_RL, LINK_TRAINING_EN and SPEED_GEN bits interleaved with sleeps. Now, after removing triggering PCI_EXP_LNKCTL_RL, there is no need to explicitly disable LINK_TRAINING_EN bit. So remove this code too. The problematic Compex cards described in previous git commits are correctly detected in advk_pcie_train_link() function even after applying all these changes. Note that with this patch, and also prior this patch, some NVMe disks which support PCIe GEN3 with 8 GT/s speed are negotiated only at the lowest link speed 2.5 GT/s, independently of SPEED_GEN value. After manually triggering PCI_EXP_LNKCTL_RL bit (e.g. from userspace via setpci), these NVMe disks change link speed to 5 GT/s when SPEED_GEN was configured to GEN2. This issue first needs to be properly investigated. I will send a fix in the future. On the other hand, some other GEN2 PCIe cards with 5 GT/s speed are autonomously by HW autonegotiated at full 5 GT/s speed without need of any software interaction. Armada 3700 Functional Specifications describes the following steps for link training: set SPEED_GEN to GEN2, enable LINK_TRAINING_EN, poll until link training is complete, trigger PCI_EXP_LNKCTL_RL, poll until signal rate is 5 GT/s, poll until link training is complete, enable ASPM L0s. The requirement for triggering PCI_EXP_LNKCTL_RL can be explained by the need to achieve 5 GT/s speed (as changing link speed is done by throw to recovery state entered by PCI_EXP_LNKCTL_RL) or maybe as a part of enabling ASPM L0s (but in this case ASPM L0s should have been enabled prior PCI_EXP_LNKCTL_RL). It is unknown why the original pci-aardvark.c driver was triggering PCI_EXP_LNKCTL_RL bit before waiting for the link to be up. This does not align with neither PCIe base specifications nor with Armada 3700 Functional Specification. (Note that in older versions of aardvark, this bit was called incorrectly PCIE_CORE_LINK_TRAINING, so this may be the reason.) It is also unknown why Armada 3700 Functional Specification says that it is needed to trigger PCI_EXP_LNKCTL_RL for GEN2 mode, as according to PCIe base specification 5 GT/s speed negotiation is supposed to be entirely autonomous, even if initial speed is 2.5 GT/s. [1] - https://lore.kernel.org/linux-pci/87h7l8axqp.fsf@toke.dk/ [2] - https://lore.kernel.org/linux-pci/20210326124326.21163-1-pali@kernel.org/ Link: https://lore.kernel.org/r/20211005180952.6812-12-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pali Rohár authored
commit 454c5327 upstream. PCIe config space can be initialized also before pci_bridge_emul_init() call, so move rootcap initialization after PCI config space initialization. This simplifies the function a little since it removes one if (ret < 0) check. Link: https://lore.kernel.org/r/20211005180952.6812-11-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pali Rohár authored
commit 223dec14 upstream. Commit 43f5c77b ("PCI: aardvark: Fix reporting CRS value") fixed handling of CRS response and when CRSSVE flag was not enabled it marked CRS response as failed transaction (due to simplicity). But pci-aardvark.c driver is already waiting up to the PIO_RETRY_CNT count for PIO config response and so we can with a small change implement re-issuing of config requests as described in PCIe base specification. This change implements re-issuing of config requests when response is CRS. Set upper bound of wait cycles to around PIO_RETRY_CNT, afterwards the transaction is marked as failed and an all-ones value is returned as before. We do this by returning appropriate error codes from function advk_pcie_check_pio_status(). On CRS we return -EAGAIN and caller then reissues transaction. Link: https://lore.kernel.org/r/20211005180952.6812-10-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Marek Behún <kabel@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pali Rohár authored
commit 1d1cd163 upstream. According to PCI Express Base Specifications (rev 4.0, 6.6.1 "Conventional reset"), after fundamental reset a 100ms delay is needed prior to enabling link training. Update comment in code to reflect this requirement. Link: https://lore.kernel.org/r/20201202184659.3795-1-pali@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Marek Behún authored
commit 67cb2a4c upstream. Avoid code repetition in advk_pcie_rd_conf() by handling errors with goto jump, as is customary in kernel. Link: https://lore.kernel.org/r/20211005180952.6812-9-kabel@kernel.org Fixes: 43f5c77b ("PCI: aardvark: Fix reporting CRS value") Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Christophe Leroy authored
commit 5bb60ea6 upstream. Since the commit c118c730 ("powerpc/32: Fix vmap stack - Do not activate MMU before reading task struct") a vmap stack overflow results in a hard lockup. This is because emergency_ctx is still addressed with its virtual address allthough data MMU is not active anymore at that time. Fix it by using a physical address instead. Fixes: c118c730 ("powerpc/32: Fix vmap stack - Do not activate MMU before reading task struct") Cc: stable@vger.kernel.org # v5.10+ Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/ce30364fb7ccda489272af4a1612b6aa147e1d23.1637227521.git.christophe.leroy@csgroup.eu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dylan Hung authored
commit 9dbe33cf upstream. The issue happened randomly in runtime. The message "Link is Down" is popped but soon it recovered to "Link is Up". The "Link is Down" results from the incorrect read data for reading the PHY register via MDIO bus. The correct sequence for reading the data shall be: 1. fire the command 2. wait for command done (this step was missing) 3. wait for data idle 4. read data from data register Cc: stable@vger.kernel.org Fixes: f160e994 ("net: phy: Add mdio-aspeed") Reviewed-by: Joel Stanley <joel@jms.id.au> Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Adrian Hunter authored
commit 3d7c194b upstream. The block layer forces a minimum segment size of PAGE_SIZE, so a segment can be too big for the ADMA table, if PAGE_SIZE >= 64KiB. Fix by writing multiple descriptors, noting that the ADMA table is sized for 4KiB chunks anyway, so it will be big enough. Reported-and-tested-by: Bough Chen <haibo.chen@nxp.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211115082345.802238-1-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tim Harvey authored
commit adab993c upstream. On IMX SoC's which support CMDQ the following can occur during high a high cpu load: mmc2: cqhci: ============ CQHCI REGISTER DUMP =========== mmc2: cqhci: Caps: 0x0000310a | Version: 0x00000510 mmc2: cqhci: Config: 0x00001001 | Control: 0x00000000 mmc2: cqhci: Int stat: 0x00000000 | Int enab: 0x00000006 mmc2: cqhci: Int sig: 0x00000006 | Int Coal: 0x00000000 mmc2: cqhci: TDL base: 0x8003f000 | TDL up32: 0x00000000 mmc2: cqhci: Doorbell: 0xbf01dfff | TCN: 0x00000000 mmc2: cqhci: Dev queue: 0x00000000 | Dev Pend: 0x08000000 mmc2: cqhci: Task clr: 0x00000000 | SSC1: 0x00011000 mmc2: cqhci: SSC2: 0x00000001 | DCMD rsp: 0x00000800 mmc2: cqhci: RED mask: 0xfdf9a080 | TERRI: 0x00000000 mmc2: cqhci: Resp idx: 0x0000000d | Resp arg: 0x00000000 mmc2: sdhci: ============ SDHCI REGISTER DUMP =========== mmc2: sdhci: Sys addr: 0x7c722000 | Version: 0x00000002 mmc2: sdhci: Blk size: 0x00000200 | Blk cnt: 0x00000020 mmc2: sdhci: Argument: 0x00018000 | Trn mode: 0x00000023 mmc2: sdhci: Present: 0x01f88008 | Host ctl: 0x00000030 mmc2: sdhci: Power: 0x00000002 | Blk gap: 0x00000080 mmc2: sdhci: Wake-up: 0x00000008 | Clock: 0x0000000f mmc2: sdhci: Timeout: 0x0000008f | Int stat: 0x00000000 mmc2: sdhci: Int enab: 0x107f4000 | Sig enab: 0x107f4000 mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000502 mmc2: sdhci: Caps: 0x07eb0000 | Caps_1: 0x8000b407 mmc2: sdhci: Cmd: 0x00000d1a | Max curr: 0x00ffffff mmc2: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0xffc003ff mmc2: sdhci: Resp[2]: 0x328f5903 | Resp[3]: 0x00d07f01 mmc2: sdhci: Host ctl2: 0x00000088 mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0xfe179020 mmc2: sdhci-esdhc-imx: ========= ESDHC IMX DEBUG STATUS DUMP ==== mmc2: sdhci-esdhc-imx: cmd debug status: 0x2120 mmc2: sdhci-esdhc-imx: data debug status: 0x2200 mmc2: sdhci-esdhc-imx: trans debug status: 0x2300 mmc2: sdhci-esdhc-imx: dma debug status: 0x2400 mmc2: sdhci-esdhc-imx: adma debug status: 0x2510 mmc2: sdhci-esdhc-imx: fifo debug status: 0x2680 mmc2: sdhci-esdhc-imx: async fifo debug status: 0x2750 mmc2: sdhci: ============================================ For now, disable CMDQ support on the imx8qm/imx8qxp/imx8mm until the issue is found and resolved. Fixes: bb6e3581 ("mmc: sdhci-esdhc-imx: add CMDQ support") Fixes: cde5e8e9 ("mmc: sdhci-esdhc-imx: Add an new esdhc_soc_data for i.MX8MM") Cc: stable@vger.kernel.org Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20211103165415.2016-1-tharvey@gateworks.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Steven Rostedt (VMware) authored
commit a55f224f upstream. If a event is filtered by pid and a trigger that requires processing of the event to happen is a attached to the event, the discard portion does not take the pid filtering into account, and the event will then be recorded when it should not have been. Cc: stable@vger.kernel.org Fixes: 3fdaf80f ("tracing: Implement event pid filtering") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jiri Olsa authored
commit 1880ed71 upstream. Add missing 'tu' variable initialization in the probes loop, otherwise the head 'tu' is used instead of added probes. Link: https://lkml.kernel.org/r/20211123142801.182530-1-jolsa@kernel.org Cc: stable@vger.kernel.org Fixes: 99c9a923 ("tracing/uprobe: Fix double perf_event linking on multiprobe uprobe") Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Jiri Olsa <jolsa@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nicholas Piggin authored
commit cf0b0e37 upstream. The POWER9 ERAT flush instruction is a SLBIA with IH=7, which is a reserved value on POWER7/8. On POWER8 this invalidates the SLB entries above index 0, similarly to SLBIA IH=0. If the SLB entries are invalidated, and then the guest is bypassed, the host SLB does not get re-loaded, so the bolted entries above 0 will be lost. This can result in kernel stack access causing a SLB fault. Kernel stack access causing a SLB fault was responsible for the infamous mega bug (search "Fix SLB reload bug"). Although since commit 48e7b769 ("powerpc/64s/hash: Convert SLB miss handlers to C") that starts using the kernel stack in the SLB miss handler, it might only result in an infinite loop of SLB faults. In any case it's a bug. Fix this by only executing the instruction on >= POWER9 where IH=7 is defined not to invalidate the SLB. POWER7/8 don't require this ERAT flush. Fixes: 50087112 ("KVM: PPC: Book3S HV: Invalidate ERAT when flushing guest TLB entries") Cc: stable@vger.kernel.org # v5.2+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211119031627.577853-1-npiggin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stefano Stabellini authored
commit 36e8f60f upstream. If the xenstore page hasn't been allocated properly, reading the value of the related hvm_param (HVM_PARAM_STORE_PFN) won't actually return error. Instead, it will succeed and return zero. Instead of attempting to xen_remap a bad guest physical address, detect this condition and return early. Note that although a guest physical address of zero for HVM_PARAM_STORE_PFN is theoretically possible, it is not a good choice and zero has never been validly used in that capacity. Also recognize all bits set as an invalid value. For 32-bit Linux, any pfn above ULONG_MAX would get truncated. Pfns above ULONG_MAX should never be passed by the Xen tools to HVM guests anyway, so check for this condition and return early. Cc: stable@vger.kernel.org Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com> Reviewed-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Link: https://lore.kernel.org/r/20211123210748.1910236-1-sstabellini@kernel.org Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stefano Stabellini authored
commit 08f6c2b0 upstream. In case of errors in xenbus_init (e.g. missing xen_store_gfn parameter), we goto out_error but we forget to reset xen_store_domain_type to XS_UNKNOWN. As a consequence xenbus_probe_initcall and other initcalls will still try to initialize xenstore resulting into a crash at boot. [ 2.479830] Call trace: [ 2.482314] xb_init_comms+0x18/0x150 [ 2.486354] xs_init+0x34/0x138 [ 2.489786] xenbus_probe+0x4c/0x70 [ 2.498432] xenbus_probe_initcall+0x2c/0x7c [ 2.503944] do_one_initcall+0x54/0x1b8 [ 2.507358] kernel_init_freeable+0x1ac/0x210 [ 2.511617] kernel_init+0x28/0x130 [ 2.516112] ret_from_fork+0x10/0x20 Cc: <Stable@vger.kernel.org> Cc: jbeulich@suse.com Signed-off-by: Stefano Stabellini <stefano.stabellini@xilinx.com> Link: https://lore.kernel.org/r/20211115222719.2558207-1-sstabellini@kernel.org Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Miklos Szeredi authored
commit 47344172 upstream. Checking buf->flags should be done before the pipe_buf_release() is called on the pipe buffer, since releasing the buffer might modify the flags. This is exactly what page_cache_pipe_buf_release() does, and which results in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was trying to fix. Reported-by: Justin Forbes <jmforbes@linuxtx.org> Fixes: 712a9510 ("fuse: fix page stealing") Cc: <stable@vger.kernel.org> # v2.6.35 Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
commit b535917c upstream. The free_rtllib() function frees the "dev" pointer so there is use after free on the next line. Re-arrange things to avoid that. Fixes: 66898177 ("staging: rtl8192e: Fix unload/reload problem") Cc: stable <stable@vger.kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211117072016.GA5237@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Takashi Iwai authored
commit ffcf7ae9 upstream. snd_ctl_remove() has to be called with card->controls_rwsem held (when called after the card instantiation). This patch adds the missing rwsem calls around it. Fixes: 510e340e ("staging: greybus: audio: Add helper APIs for dynamic audio modules") Cc: stable <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20211116072027.18466-1-tiwai@suse.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Noralf Trønnes authored
commit 7865dd24 upstream. Commit b4a1ed0c ("fbdev: make FB_BACKLIGHT a tristate") forgot to update fbtft breaking its backlight support when FB_BACKLIGHT is a module. Since FB_TFT selects FB_BACKLIGHT there's no need for this conditional so just remove it and we're good. Fixes: b4a1ed0c ("fbdev: make FB_BACKLIGHT a tristate") Cc: <stable@vger.kernel.org> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Noralf Trønnes <noralf@tronnes.org> Link: https://lore.kernel.org/r/20211105204358.2991-1-noralf@tronnes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jason Gerecke authored
commit 7fb0413b upstream. The HID descriptor of many of Wacom's touch input devices include a "Confidence" usage that signals if a particular touch collection contains useful data. The driver does not look at this flag, however, which causes even invalid contacts to be reported to userspace. A lucky combination of kernel event filtering and device behavior (specifically: contact ID 0 == invalid, contact ID >0 == valid; and order all data so that all valid contacts are reported before any invalid contacts) spare most devices from any visibly-bad behavior. The DTH-2452 is one example of an unlucky device that misbehaves. It uses ID 0 for both the first valid contact and all invalid contacts. Because we report both the valid and invalid contacts, the kernel reports that contact 0 first goes down (valid) and then goes up (invalid) in every report. This causes ~100 clicks per second simply by touching the screen. This patch inroduces new `confidence` flag in our `hid_data` structure. The value is initially set to `true` at the start of a report and can be set to `false` if an invalid touch usage is seen. Link: https://github.com/linuxwacom/input-wacom/issues/270 Fixes: f8b6a747 ("HID: wacom: generic: Support multiple tools per report") Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Tested-by: Joshua Dickens <joshua.dickens@wacom.com> Cc: <stable@vger.kernel.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Helge Deller authored
commit 98400ad7 upstream. This reverts commit 279917e2 . With the CONFIG_HARDENED_USERCOPY option enabled, this patch triggers kernel bugs at runtime: usercopy: Kernel memory overwrite attempt detected to kernel text (offset 2084839, size 6)! kernel BUG at mm/usercopy.c:99! Backtrace: IAOQ[0]: usercopy_abort+0xc4/0xe8 [<00000000406ed1c8>] __check_object_size+0x174/0x238 [<00000000407086d4>] copy_strings.isra.0+0x3e8/0x708 [<0000000040709a20>] do_execveat_common.isra.0+0x1bc/0x328 [<000000004070b760>] compat_sys_execve+0x7c/0xb8 [<0000000040303eb8>] syscall_exit+0x0/0x14 The problem is, that we have an init section of at least 2MB size which starts at _stext and is freed after bootup. If then later some kernel data is (temporarily) stored in this free memory, check_kernel_text_object() will trigger a bug since the data appears to be inside the kernel text (>=_stext) area: if (overlaps(ptr, len, _stext, _etext)) usercopy_abort("kernel text"); Signed-off-by: Helge Deller <deller@gmx.de> Cc: stable@kernel.org # 5.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Hans Verkuil authored
commit 13cbaa4c upstream. When the reply for a non-blocking transmit arrives, the sequence field for that reply was never filled in, so userspace would have no way of associating the reply to the original transmit. Copy the sequence field to ensure that this is now possible. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 0dbacebe ([media] cec: move the CEC framework out of staging and to media) Cc: <stable@vger.kernel.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Takashi Iwai authored
commit 05ec7161 upstream. HP ProBook 435 G7 (SSID 103c:8735) needs the similar quirk as another HP ProBook for enabling the mute and the mic-mute LEDs. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215021 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211118071636.14738-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Werner Sembach authored
commit 174a7fb3 upstream. This applies a SND_PCI_QUIRK(...) to the ASRock NUC Box 1100 series. This fixes the issue of the headphone jack not being detected unless warm rebooted from a certain other OS. When booting a certain other OS some coeff settings are changed that enable the audio jack. These settings are preserved on a warm reboot and can be easily dumped. The relevant indexes and values where gathered by naively diff-ing and reading a working and a non-working coeff dump. Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211112110704.1022501-1-wse@tuxedocomputers.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Takashi Iwai authored
commit 76c47183 upstream. The master and next_conj of rcs_ops are used for iterating the resource list entries, and currently those are supposed to return the current value. The problem is that next_conf may go over the last entry before the loop abort condition is evaluated, and it may return the "current" value that is beyond the array size. It was caught recently as a GPF, for example. Those return values are, however, never actually evaluated, hence basically we don't have to consider the current value as the return at all. By dropping those return values, the potential out-of-range access above is also fixed automatically. This patch changes the return type of master and next_conj callbacks to void and drop the superfluous code accordingly. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=214985 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211118215729.26257-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Todd Kjos authored
commit c21a80ca upstream. This is a partial revert of commit 29bc22ac ("binder: use euid from cred instead of using task"). Setting sender_euid using proc->cred caused some Android system test regressions that need further investigation. It is a partial reversion because subsequent patches rely on proc->cred. Fixes: 29bc22ac ("binder: use euid from cred instead of using task") Cc: stable@vger.kernel.org # 4.4+ Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Todd Kjos <tkjos@google.com> Change-Id: I9b1769a3510fed250bb21859ef8beebabe034c66 Link: https://lore.kernel.org/r/20211112180720.2858135-1-tkjos@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
commit 6cca13de upstream. Fix the circular lock dependency and unbalanced unlock of addess0_mutex introduced when fixing an address0_mutex enumeration retry race in commit ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race") Make sure locking order between port_dev->status_lock and address0_mutex is correct, and that address0_mutex is not unlocked in hub_port_connect "done:" codepath which may be reached without locking address0_mutex Fixes: 6ae6dc22 ("usb: hub: Fix usb enumeration issue due to address0 race") Cc: <stable@vger.kernel.org> Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
commit 6ae6dc22 upstream. xHC hardware can only have one slot in default state with address 0 waiting for a unique address at a time, otherwise "undefined behavior may occur" according to xhci spec 5.4.3.4 The address0_mutex exists to prevent this across both xhci roothubs. If hub_port_init() fails, it may unlock the mutex and exit with a xhci slot in default state. If the other xhci roothub calls hub_port_init() at this point we end up with two slots in default state. Make sure the address0_mutex protects the slot default state across hub_port_init() retries, until slot is addressed or disabled. Note, one known minor case is not fixed by this patch. If device needs to be reset during resume, but fails all hub_port_init() retries in usb_reset_and_verify_device(), then it's possible the slot is still left in default state when address0_mutex is unlocked. Cc: <stable@vger.kernel.org> Fixes: 638139eb ("usb: hub: allow to process more usb hub events in parallel") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ondřej Jirman authored
commit 36246883 upstream. The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate bit in the mask register. In fact, interrupts are enabled when the mask is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects BC_LVL interrupt to be enabled. This causes inability of the driver to recognize cable unplug events in host mode (unplug is recognized only via a COMP_CHNG interrupt). In device mode this bug was masked by simultaneous triggering of the VBUS change interrupt, because of loss of VBUS when the port peer is providing power. Fixes: 48242e30 ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"") Cc: stable <stable@vger.kernel.org> Cc: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Ondrej Jirman <megous@megous.com> Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Dan Carpenter authored
commit d4d2e532 upstream. If the first call to devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0) fails with something other than -ENODEV then it leads to an error pointer dereference. For those errors we should just jump directly to the error handling. Fixes: 8253a34b ("usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle") Cc: stable <stable@vger.kernel.org> Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211117074923.GF5237@kili Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nikolay Aleksandrov authored
commit 1c743127 upstream. When we try to add an IPv6 nexthop and IPv6 is not enabled (!CONFIG_IPV6) we'll hit a NULL pointer dereference[1] in the error path of nh_create_ipv6() due to calling ipv6_stub->fib6_nh_release. The bug has been present since the beginning of IPv6 nexthop gateway support. Commit 1aefd3de ("ipv6: Add fib6_nh_init and release to stubs") tells us that only fib6_nh_init has a dummy stub because fib6_nh_release should not be called if fib6_nh_init returns an error, but the commit below added a call to ipv6_stub->fib6_nh_release in its error path. To fix it return the dummy stub's -EAFNOSUPPORT error directly without calling ipv6_stub->fib6_nh_release in nh_create_ipv6()'s error path. [1] Output is a bit truncated, but it clearly shows the error. BUG: kernel NULL pointer dereference, address: 000000000000000000 #PF: supervisor instruction fetch in kernel modede #PF: error_code(0x0010) - not-present pagege PGD 0 P4D 0 Oops: 0010 [#1] PREEMPT SMP NOPTI CPU: 4 PID: 638 Comm: ip Kdump: loaded Not tainted 5.16.0-rc1+ #446 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/01/2014 RIP: 0010:0x0 Code: Unable to access opcode bytes at RIP 0xffffffffffffffd6. RSP: 0018:ffff888109f5b8f0 EFLAGS: 00010286^Ac RAX: 0000000000000000 RBX: ffff888109f5ba28 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff8881008a2860 RBP: ffff888109f5b9d8 R08: 0000000000000000 R09: 0000000000000000 R10: ffff888109f5b978 R11: ffff888109f5b948 R12: 00000000ffffff9f R13: ffff8881008a2a80 R14: ffff8881008a2860 R15: ffff8881008a2840 FS: 00007f98de70f100(0000) GS:ffff88822bf00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffffffffffd6 CR3: 0000000100efc000 CR4: 00000000000006e0 Call Trace: <TASK> nh_create_ipv6+0xed/0x10c rtm_new_nexthop+0x6d7/0x13f3 ? check_preemption_disabled+0x3d/0xf2 ? lock_is_held_type+0xbe/0xfd rtnetlink_rcv_msg+0x23f/0x26a ? check_preemption_disabled+0x3d/0xf2 ? rtnl_calcit.isra.0+0x147/0x147 netlink_rcv_skb+0x61/0xb2 netlink_unicast+0x100/0x187 netlink_sendmsg+0x37f/0x3a0 ? netlink_unicast+0x187/0x187 sock_sendmsg_nosec+0x67/0x9b ____sys_sendmsg+0x19d/0x1f9 ? copy_msghdr_from_user+0x4c/0x5e ? rcu_read_lock_any_held+0x2a/0x78 ___sys_sendmsg+0x6c/0x8c ? asm_sysvec_apic_timer_interrupt+0x12/0x20 ? lockdep_hardirqs_on+0xd9/0x102 ? sockfd_lookup_light+0x69/0x99 __sys_sendmsg+0x50/0x6e do_syscall_64+0xcb/0xf2 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f98dea28914 Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b5 0f 1f 80 00 00 00 00 48 8d 05 e9 5d 0c 00 8b 00 85 c0 75 13 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 41 89 d4 55 48 89 f5 53 RSP: 002b:00007fff859f5e68 EFLAGS: 00000246 ORIG_RAX: 000000000000002e2e RAX: ffffffffffffffda RBX: 00000000619cb810 RCX: 00007f98dea28914 RDX: 0000000000000000 RSI: 00007fff859f5ed0 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000008 R10: fffffffffffffce6 R11: 0000000000000246 R12: 0000000000000001 R13: 000055c0097ae520 R14: 000055c0097957fd R15: 00007fff859f63a0 </TASK> Modules linked in: bridge stp llc bonding virtio_net Cc: stable@vger.kernel.org Fixes: 53010f99 ("nexthop: Add support for IPv6 gateways") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Albert Wang authored
commit 26288448 upstream. In the endpoint interrupt functions dwc3_gadget_endpoint_transfer_in_progress() and dwc3_gadget_endpoint_trbs_complete() will dereference the endpoint descriptor. But it could be cleared in __dwc3_gadget_ep_disable() when accessory disconnected. So we need to check whether it is null or not before dereferencing it. Fixes: f09ddcfc ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers") Cc: stable <stable@vger.kernel.org> Reviewed-by: Jack Pham <quic_jackp@quicinc.com> Signed-off-by: Albert Wang <albertccwang@google.com> Link: https://lore.kernel.org/r/20211109092642.3507692-1-albertccwang@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thinh Nguyen authored
commit 63c4c320 upstream. The programming guide noted that the driver needs to verify if the link state is in U0 before executing the Start Transfer command. If it's not in U0, the driver needs to perform remote wakeup. This is not accurate. If the link state is in U1/U2, then the controller will not respond to link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command will trigger a link recovery if it is in U1/U2. A clarification will be added to the programming guide for all controller versions. The current implementation shouldn't cause any functional issue. It may occasionally report an invalid time out warning from failed link recovery request. The driver will still go ahead with the Start Transfer command if the remote wakeup fails. The new change only initiates remote wakeup where it is needed, which is when the link state is in L1/L2/U3. Fixes: c36d8e94 ("usb: dwc3: gadget: put link to U0 before Start Transfer") Cc: <stable@vger.kernel.org> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thinh Nguyen authored
commit d74dc3e9 upstream. The End Transfer command from a stream endpoint will generate a NoStream event, and we should ignore it. Currently we set the flag DWC3_EP_IGNORE_NEXT_NOSTREAM to track this prior to sending the command, and it will be cleared on the next stream event. However, a stream event may be generated before the End Transfer command completion and prematurely clear the flag. Fix this by setting the flag on End Transfer completion instead. Fixes: 140ca4cf ("usb: dwc3: gadget: Handle stream transfers") Cc: <stable@vger.kernel.org> Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/cee1253af4c3600edb878d11c9c08b040817ae23.1635203975.git.Thinh.Nguyen@synopsys.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nathan Chancellor authored
commit 310780e8 upstream. A new commit in LLVM causes an error on the use of 'long double' when '-mno-x87' is used, which the kernel does through an alias, '-mno-80387' (see the LLVM commit below for more details around why it does this). drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY); ^ drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY' #define DWC2_RETRY_WAIT_DELAY (1 * 1E6L) ^ 1 error generated. This happens due to the use of a 'long double' literal. The 'E6' part of '1E6L' causes the literal to be a 'double' then the 'L' suffix promotes it to 'long double'. There is no visible reason for a floating point value in this driver, as the value is only used as a parameter to a function that expects an integer type. Use NSEC_PER_MSEC, which is the same integer value as '1E6L', to avoid changing functionality but fix the error. Link: https://github.com/ClangBuiltLinux/linux/issues/1497 Link: https://github.com/llvm/llvm-project/commit/a8083d42b1c346e21623a1d36d1f0cadd7801d83 Fixes: 6ed30a7d ("usb: dwc2: host: use hrtimer for NAK retries") Cc: stable <stable@vger.kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: John Keeping <john@metanate.com> Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-