commit 8a0d19c5 upstream.

when A sends a data to B, then A close() and enter into SHUTDOWN_PENDING
state, if B neither claim his rwnd is 0 nor send SACK for this data, A
will keep retransmitting this data until t5 timeout, Max.Retrans times
can't work anymore, which is bad.

if B's rwnd is not 0, it should send abort after Max.Retrans times, only
when B's rwnd == 0 and A's retransmitting beyonds Max.Retrans times, A
will start t5 timer, which is also commit f8d96052 ("sctp: Enforce
retransmission limit during shutdown") means, but it lacks the condition
peer rwnd == 0.

so fix it by adding a bit (zero_window_announced) in peer to record if
the last rwnd is 0. If it was, zero_window_announced will be set. and use
this bit to decide if start t5 timer when local.state is SHUTDOWN_PENDING.

Fixes: commit f8d96052

 ("sctp: Enforce retransmission limit during shutdown")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 3.2: change sack_needed to bitfield as done earlier upstream]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a74a8216

 upstream.

rme96 driver needs to reset DAC depending on the sample rate, and this
results in resetting to the max volume suddenly.  It's because of the
missing call of snd_rme96_apply_dac_volume().

However, calling this function right after the DAC reset still may not
work, and we need some delay before this call.  Since the DAC reset
and the procedure after that are performed in the spinlock, we delay
the DAC volume restore at the end after the spinlock.

Reported-and-tested-by: Sylvain LABOISNE <maeda1@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 096b110a

 upstream.

if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2

Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 30ce6e1c

 upstream.

The block allocated at the start of btree_split_sibling() is never
released if later insert_at() fails.

Fix this by releasing the previously allocated bufio block using
unlock_block().

Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit f9fa1887

 upstream.

qset_fill_page_list() do not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit d98f1cd0

 upstream.

When I connect an Intel SSD to SATA SIL controller (PCI ID 1095:3114), any
TRIM command results in I/O errors being reported in the log. There is
other similar error reported with TRIM and the SIL controller:
https://bugs.centos.org/view.php?id=5880

Apparently the controller doesn't support TRIM commands. This patch
disables TRIM support on the SATA SIL controller.

ata7.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
ata7.00: BMDMA2 stat 0x50001
ata7.00: failed command: DATA SET MANAGEMENT
ata7.00: cmd 06/01:01:00:00:00/00:00:00:00:00/a0 tag 0 dma 512 out
         res 51/04:01:00:00:00/00:00:00:00:00/a0 Emask 0x1 (device error)
ata7.00: status: { DRDY ERR }
ata7.00: error: { ABRT }
ata7.00: device reported invalid CHS sector 0
sd 8:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 8:0:0:0: [sdb] tag#0 Sense Key : Illegal Request [current] [descriptor]
sd 8:0:0:0: [sdb] tag#0 Add. Sense: Unaligned write command
sd 8:0:0:0: [sdb] tag#0 CDB: Write same(16) 93 08 00 00 00 00 00 21 95 88 00 20 00 00 00 00
blk_update_request: I/O error, dev sdb, sector 2200968

Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 023113d2

 upstream.

Current code doesn't update port value of Port Multiplier(PM) when
sending FIS of softreset to device, command will fail if FBS is
enabled.

There are two ways to fix the issue: the first is to disable FBS
before sending softreset command to PM device and the second is
to update port value of PM when sending command.

For the first way, i can't find any related rule in AHCI Spec. The
second way can avoid disabling FBS and has better performance.

Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit bc23f0c8

 upstream.

Ted and Namjae have reported that truncated pages don't get timely
reclaimed after being truncated in data=journal mode. The following test
triggers the issue easily:

for (i = 0; i < 1000; i++) {
	pwrite(fd, buf, 1024*1024, 0);
	fsync(fd);
	fsync(fd);
	ftruncate(fd, 0);
}

The reason is that journal_unmap_buffer() finds that truncated buffers
are not journalled (jh->b_transaction == NULL), they are part of
checkpoint list of a transaction (jh->b_cp_transaction != NULL) and have
been already written out (!buffer_dirty(bh)). We clean such buffers but
we leave them in the checkpoint list. Since checkpoint transaction holds
a reference to the journal head, these buffers cannot be released until
the checkpoint transaction is cleaned up. And at that point we don't
call release_buffer_page() anymore so pages detached from mapping are
lingering in the system waiting for reclaim to find them and free them.

Fix the problem by removing buffers from transaction checkpoint lists
when journal_unmap_buffer() finds out they don't have to be there
anymore.

Reported-and-tested-by: Namjae Jeon <namjae.jeon@samsung.com>
Fixes: de1b7941


Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a4dad1ae

 upstream.

In ext4, the bottom two bits of {a,c,m}time_extra are used to extend
the {a,c,m}time fields, deferring the year 2038 problem to the year
2446.

When decoding these extended fields, for times whose bottom 32 bits
would represent a negative number, sign extension causes the 64-bit
extended timestamp to be negative as well, which is not what's
intended.  This patch corrects that issue, so that the only negative
{a,c,m}times are those between 1901 and 1970 (as per 32-bit signed
timestamps).

Some older kernels might have written pre-1970 dates with 1,1 in the
extra bits.  This patch treats those incorrectly-encoded dates as
pre-1970, instead of post-2311, until kernel 4.20 is released.
Hopefully by then e2fsck will have fixed up the bad data.

Also add a comment explaining the encoding of ext4's extra {a,c,m}time
bits.

Signed-off-by: David Turner <novalis@novalis.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Mark Harris <mh8928@yahoo.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=23732
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7c90e610

 upstream.

CP2110 ID (0x10c4, 0xea80) doesn't belong here because it's a HID
and completely different from CP210x devices.

Signed-off-by: Konstantin Shkolnyy <konstantin.shkolnyy@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 3ca8138f upstream.

I got a report about unkillable task eating CPU. Further
investigation shows, that the problem is in the fuse_fill_write_pages()
function. If iov's first segment has zero length, we get an infinite
loop, because we never reach iov_iter_advance() call.

Fix this by calling iov_iter_advance() before repeating an attempt to
copy data from userspace.

A similar problem is described in 124d3b70

 ("fix writev regression:
pan hanging unkillable and un-straceable"). If zero-length segmend
is followed by segment with invalid address,
iov_iter_fault_in_readable() checks only first segment (zero-length),
iov_iter_copy_from_user_atomic() skips it, fails at second and
returns zero -> goto again without skipping zero-length segment.

Patch calls iov_iter_advance() before goto again: we'll skip zero-length
segment at second iteraction and iov_iter_fault_in_readable() will detect
invalid address.

Special thanks to Konstantin Khlebnikov, who helped a lot with the commit
description.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Maxim Patlasov <mpatlasov@parallels.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Fixes: ea9b9907

 ("fuse: implement perform_write")
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 0ebf7f10

 upstream.

The thing got broken back in 2002 - sysvfs does *not* have inline
symlinks; even short ones have bodies stored in the first block
of file.  sysv_symlink() handles that correctly; unfortunately,
attempting to look an existing symlink up will end up confusing
them for inline symlinks, and interpret the block number containing
the body as the body itself.

Nobody has noticed until now, which says something about the level
of testing sysvfs gets ;-/

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 22eab110

 upstream.

When restarting a syscall with regs->ax == -ERESTART_RESTARTBLOCK,
regs->ax is assigned to a restart_syscall number.  For x32 tasks, this
syscall number must have __X32_SYSCALL_BIT set, otherwise it will be
an x86_64 syscall number instead of a valid x32 syscall number. This
issue has been there since the introduction of x32.

Reported-by: strace/tests/restart_syscall.test
Reported-and-tested-by: Elvira Khabirova <lineprinter0@gmail.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Elvira Khabirova <lineprinter0@gmail.com>
Link: http://lkml.kernel.org/r/20151130215436.GA25996@altlinux.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 8295c699

 upstream.

root_domain::rto_mask allocated through alloc_cpumask_var()
contains garbage data, this may cause problems. For instance,
When doing pull_rt_task(), it may do useless iterations if
rto_mask retains some extra garbage bits. Worse still, this
violates the isolated domain rule for clustered scheduling
using cpuset, because the tasks(with all the cpus allowed)
belongs to one root domain can be pulled away into another
root domain.

The patch cleans the garbage by using zalloc_cpumask_var()
instead of alloc_cpumask_var() for root_domain::rto_mask
allocation, thereby addressing the issues.

Do the same thing for root_domain's other cpumask memembers:
dlo_mask, span, and online.

Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1449057179-29321-1-git-send-email-xlpang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[lizf: there's no rd->dlo_mask, so remove the change to it]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit ee9159dd

 upstream.

The N_X25 line discipline may access the previous line discipline's closed
and already-freed private data on open [1].

The tty->disc_data field _never_ refers to valid data on entry to the
line discipline's open() method. Rather, the ldisc is expected to
initialize that field for its own use for the lifetime of the instance
(ie. from open() to close() only).

[1]
    [  634.336761] ==================================================================
    [  634.338226] BUG: KASAN: use-after-free in x25_asy_open_tty+0x13d/0x490 at addr ffff8800a743efd0
    [  634.339558] Read of size 4 by task syzkaller_execu/8981
    [  634.340359] =============================================================================
    [  634.341598] BUG kmalloc-512 (Not tainted): kasan: bad access detected
    ...
    [  634.405018] Call Trace:
    [  634.405277] dump_stack (lib/dump_stack.c:52)
    [  634.405775] print_trailer (mm/slub.c:655)
    [  634.406361] object_err (mm/slub.c:662)
    [  634.406824] kasan_report_error (mm/kasan/report.c:138 mm/kasan/report.c:236)
    [  634.409581] __asan_report_load4_noabort (mm/kasan/report.c:279)
    [  634.411355] x25_asy_open_tty (drivers/net/wan/x25_asy.c:559 (discriminator 1))
    [  634.413997] tty_ldisc_open.isra.2 (drivers/tty/tty_ldisc.c:447)
    [  634.414549] tty_set_ldisc (drivers/tty/tty_ldisc.c:567)
    [  634.415057] tty_ioctl (drivers/tty/tty_io.c:2646 drivers/tty/tty_io.c:2879)
    [  634.423524] do_vfs_ioctl (fs/ioctl.c:43 fs/ioctl.c:607)
    [  634.427491] SyS_ioctl (fs/ioctl.c:622 fs/ioctl.c:613)
    [  634.427945] entry_SYSCALL_64_fastpath (arch/x86/entry/entry_64.S:188)

Reported-and-tested-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit c812012f

 upstream.

If we pass in an empty nfs_fattr struct to nfs_update_inode, it will
(correctly) not update any of the attributes, but it then clears the
NFS_INO_INVALID_ATTR flag, which indicates that the attributes are
up to date. Don't clear the flag if the fattr struct has no valid
attrs to apply.

Reviewed-by: Steve French <steve.french@primarydata.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit c2489e07

 upstream.

The following test program from Dmitry can cause softlockups or RCU
stalls as it copies 1GB from tmpfs into eventfd and we don't have any
scheduling point at that path in sendfile(2) implementation:

        int r1 = eventfd(0, 0);
        int r2 = memfd_create("", 0);
        unsigned long n = 1<<30;
        fallocate(r2, 0, 0, n);
        sendfile(r1, r2, 0, n);

Add cond_resched() into __splice_from_pipe() to fix the problem.

CC: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit c725bfce upstream.

Commit 296291cd

 (mm: make sendfile(2) killable) fixed an issue where
sendfile(2) was doing a lot of tiny writes into a filesystem and thus
was unkillable for a long time. However sendfile(2) can be (mis)used to
issue lots of writes into arbitrary file descriptor such as evenfd or
similar special file descriptors which never hit the standard filesystem
write path and thus are still unkillable. E.g. the following example
from Dmitry burns CPU for ~16s on my test system without possibility to
be killed:

        int r1 = eventfd(0, 0);
        int r2 = memfd_create("", 0);
        unsigned long n = 1<<30;
        fallocate(r2, 0, 0, n);
        sendfile(r1, r2, 0, n);

There are actually quite a few tests for pending signals in sendfile
code however we data to write is always available none of them seems to
trigger. So fix the problem by adding a test for pending signal into
splice_from_pipe_next() also before the loop waiting for pipe buffers to
be available. This should fix all the lockup issues with sendfile of the
do-ton-of-tiny-writes nature.

Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7cecd9ab

 upstream.

According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.

Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
  in operating state
- A bus error condition occurs which activates EI interrupt, system is
  still suspended which means EI interrupt will be not be handled nor
  cleared.

If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.

By simply reading the IR register on start we will clear any previous
conditions that could be present.

Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
[lizf: Backported to 3.4: s/SJA1000_IR/REG_IR/]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 02e2a5bf

 upstream.

If md->signature == MAC_DRIVER_MAGIC and md->block_size == 1023, a single
512 byte sector would be read (secsize / 512). However the partition
structure would be located past the end of the buffer (secsize % 512).

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 638148e2

 upstream.

Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1c9e ProdID=9b01 Rev=02.32
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Now all important things are there:

wwp0s29f7u2i3 (net), ttyUSB2 (at), cdc-wdm0 (qmi), ttyUSB1 (at)

There is also ttyUSB0, but it is not usable, at least not for at.

The device works well with qmi and ModemManager-NetworkManager.
"

Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit e9f96bc5

 upstream.

From datasheet:
R17408 (4400h) HPF_C_1
R17409 (4401h) HPF_C_0
17048 -> 17408 (0x4400)
17049 -> 17409 (0x4401)

Signed-off-by: Sachin Pandhare <sachinpandhare@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit e07af133

 upstream.

Also known as Verizon U620L.

The device is modeswitched from 1410:9020 to 1410:9022 by selecting the
4th USB configuration:

 $ sudo usb_modeswitch –v 0x1410 –p 0x9020 –u 4

This configuration provides a ECM interface as well as TTYs ('Enterprise
Mode' according to the U620 Linux integration guide).

Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a91e627e

 upstream.

One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4.  For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:

correct:       CH345:
0F FE 00 00    0F FE 00 00
04 F0 01 02    04 F0 01 02
04 03 04 05    0F 03 04 05
04 06 07 08    04 06 07 08
04 09 0A 0B    0F 09 0A 0B
04 0C 0D 0E    04 0C 0D 0E
05 F7 00 00    05 F7 00 00

A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored.  The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".

These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.

(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 1ca8b201

 upstream.

The CH345 USB MIDI chip has two output ports.  However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.

It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port.  So we can just ignore the device's
descriptors, and hardcode one output port.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 98d362be

 upstream.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 01bb70ae

 upstream.

If common clock framework is configured, the driver generates a warning,
which is fixed by this change:

    root@devkit3250:~# cat /sys/bus/iio/devices/iio\:device0/in_voltage0_raw
    ------------[ cut here ]------------
    WARNING: CPU: 0 PID: 724 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
    Modules linked in: sc16is7xx snd_soc_uda1380
    CPU: 0 PID: 724 Comm: cat Not tainted 4.3.0-rc2+ #198
    Hardware name: LPC32XX SoC (Flattened Device Tree)
    Backtrace:
    [<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
    [<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
    [<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
    [<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
    [<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
    [<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
    [<>] (clk_enable) from [<>] (lpc32xx_read_raw+0x38/0x80)
    [<>] (lpc32xx_read_raw) from [<>] (iio_read_channel_info+0x70/0x94)
    [<>] (iio_read_channel_info) from [<>] (dev_attr_show+0x28/0x4c)
    [<>] (dev_attr_show) from [<>] (sysfs_kf_seq_show+0x8c/0xf0)
    [<>] (sysfs_kf_seq_show) from [<>] (kernfs_seq_show+0x2c/0x30)
    [<>] (kernfs_seq_show) from [<>] (seq_read+0x1c8/0x440)
    [<>] (seq_read) from [<>] (kernfs_fop_read+0x38/0x170)
    [<>] (kernfs_fop_read) from [<>] (do_readv_writev+0x16c/0x238)
    [<>] (do_readv_writev) from [<>] (vfs_readv+0x50/0x58)
    [<>] (vfs_readv) from [<>] (default_file_splice_read+0x1a4/0x308)
    [<>] (default_file_splice_read) from [<>] (do_splice_to+0x78/0x84)
    [<>] (do_splice_to) from [<>] (splice_direct_to_actor+0xc8/0x1cc)
    [<>] (splice_direct_to_actor) from [<>] (do_splice_direct+0xa0/0xb8)
    [<>] (do_splice_direct) from [<>] (do_sendfile+0x1a8/0x30c)
    [<>] (do_sendfile) from [<>] (SyS_sendfile64+0x104/0x10c)
    [<>] (SyS_sendfile64) from [<>] (ret_fast_syscall+0x0/0x38)

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 6adc5fd6

 upstream.

Proxy entries could have null pointer to net-device.

Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Fixes: 84920c14

 ("net: Allow ipv6 proxies and arp proxies be shown with iproute2")
Signed-off-by: David S. Miller <davem@davemloft.net>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit b81f472a

 upstream.

Do not update the read stamp after swapping out the reader page from the
write buffer. If the reader page is swapped out of the buffer before an
event is written to it, then the read_stamp may get an out of date
timestamp, as the page timestamp is updated on the first commit to that
page.

rb_get_reader_page() only returns a page if it has an event on it, otherwise
it will return NULL. At that point, check if the page being returned has
events and has not been read yet. Then at that point update the read_stamp
to match the time stamp of the reader page.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 3c25a860 upstream.

Commit fcb26ec5 ("broadcom: move all PHY_ID's to header")
updated broadcom_tbl to use PHY_IDs, but incorrectly replaced 0x0143bca0
with PHY_ID_BCM5482 (making a duplicate entry, and completely omitting
the original). Fix that.

Fixes: fcb26ec5

 ("broadcom: move all PHY_ID's to header")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 4c698046 upstream.

Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.

Fixes: 8229efda

 ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code")
CC: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7ba0c47c

 upstream.

We need to wait for the flying timers, since we
are going to free the mrtable right after it.

Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 19cd80a2 upstream.

It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.

This is clearly a bug and a warning is generated with LOCKDEP too:
WARNING: CPU: 1 PID: 5109 at kernel/sched/core.c:7404 __might_sleep+0x7d/0x90()
do not call blocking ops when !TASK_RUNNING; state=1 set at [<ffffffffa0c588d0>] usblp_wwait+0xa0/0x310 [usblp]
Modules linked in: ...
CPU: 1 PID: 5109 Comm: captmon Tainted: G        W       4.2.5-0.gef2823b-default #1
Hardware name: LENOVO 23252SG/23252SG, BIOS G2ET33WW (1.13 ) 07/24/2012
 ffffffff81a4edce ffff880236ec7ba8 ffffffff81716651 0000000000000000
 ffff880236ec7bf8 ffff880236ec7be8 ffffffff8106e146 0000000000000282
 ffffffff81a50119 000000000000028b 0000000000000000 ffff8802dab7c508
Call Trace:
...
 [<ffffffff8106e1c6>] warn_slowpath_fmt+0x46/0x50
 [<ffffffff8109a8bd>] __might_sleep+0x7d/0x90
 [<ffffffff8171b20f>] mutex_lock_interruptible_nested+0x2f/0x4b0
 [<ffffffffa0c588fc>] usblp_wwait+0xcc/0x310 [usblp]
 [<ffffffffa0c58bb2>] usblp_write+0x72/0x350 [usblp]
 [<ffffffff8121ed98>] __vfs_write+0x28/0xf0
...

Commit 7f477358

 (usblp: Implement the
ENOSPC convention) moved the set prior locking. So move it back after
the lock.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: 7f477358

 ("usblp: Implement the ENOSPC convention")
Acked-By: Pete Zaitcev <zaitcev@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 1b8e6a01 upstream.

When a passive TCP is created, we eventually call tcp_md5_do_add()
with sk pointing to the child. It is not owner by the user yet (we
will add this socket into listener accept queue a bit later anyway)

But we do own the spinlock, so amend the lockdep annotation to avoid
following splat :

[ 8451.090932] net/ipv4/tcp_ipv4.c:923 suspicious rcu_dereference_protected() usage!
[ 8451.090932]
[ 8451.090932] other info that might help us debug this:
[ 8451.090932]
[ 8451.090934]
[ 8451.090934] rcu_scheduler_active = 1, debug_locks = 1
[ 8451.090936] 3 locks held by socket_sockopt_/214795:
[ 8451.090936]  #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff855c6ac1>] __netif_receive_skb_core+0x151/0xe90
[ 8451.090947]  #1:  (rcu_read_lock){.+.+..}, at: [<ffffffff85618143>] ip_local_deliver_finish+0x43/0x2b0
[ 8451.090952]  #2:  (slock-AF_INET){+.-...}, at: [<ffffffff855acda5>] sk_clone_lock+0x1c5/0x500
[ 8451.090958]
[ 8451.090958] stack backtrace:
[ 8451.090960] CPU: 7 PID: 214795 Comm: socket_sockopt_

[ 8451.091215] Call Trace:
[ 8451.091216]  <IRQ>  [<ffffffff856fb29c>] dump_stack+0x55/0x76
[ 8451.091229]  [<ffffffff85123b5b>] lockdep_rcu_suspicious+0xeb/0x110
[ 8451.091235]  [<ffffffff8564544f>] tcp_md5_do_add+0x1bf/0x1e0
[ 8451.091239]  [<ffffffff85645751>] tcp_v4_syn_recv_sock+0x1f1/0x4c0
[ 8451.091242]  [<ffffffff85642b27>] ? tcp_v4_md5_hash_skb+0x167/0x190
[ 8451.091246]  [<ffffffff85647c78>] tcp_check_req+0x3c8/0x500
[ 8451.091249]  [<ffffffff856451ae>] ? tcp_v4_inbound_md5_hash+0x11e/0x190
[ 8451.091253]  [<ffffffff85647170>] tcp_v4_rcv+0x3c0/0x9f0
[ 8451.091256]  [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091260]  [<ffffffff856181b6>] ip_local_deliver_finish+0xb6/0x2b0
[ 8451.091263]  [<ffffffff85618143>] ? ip_local_deliver_finish+0x43/0x2b0
[ 8451.091267]  [<ffffffff85618d38>] ip_local_deliver+0x48/0x80
[ 8451.091270]  [<ffffffff85618510>] ip_rcv_finish+0x160/0x700
[ 8451.091273]  [<ffffffff8561900e>] ip_rcv+0x29e/0x3d0
[ 8451.091277]  [<ffffffff855c74b7>] __netif_receive_skb_core+0xb47/0xe90

Fixes: a8afca03

 ("tcp: md5: protects md5sig_info with RCU")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit e639b8d8 upstream.

Reset pskb in macvlan_handle_frame in case skb_share_check returned a
clone.

Fixes: 8a4eb573

 ("net: introduce rx_handler results and logic around that")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit c2e703a5 upstream.

When using call_rcu(), the called function may be delayed quite
significantly, and without a matching rcu_barrier() there's no
way to be sure it has finished.
Therefore, global state that could be gone/freed/reused should
never be touched in the callback.

Fix this in mesh by moving the atomic_dec() into the caller;
that's not really a problem since we already unlinked the path
and it will be destroyed anyway.

This fixes a crash Jouni observed when running certain tests in
a certain order, in which the mesh interface was torn down, the
memory reused for a function pointer (work struct) and running
that then crashed since the pointer had been decremented by 1,
resulting in an invalid instruction byte stream.

Fixes: eb2b9311

 ("mac80211: mesh path table implementation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 00ee5927 upstream.

If ndo_set_features fails __netdev_update_features() will return -1 but
this is wrong because it is expected to return 0 if no features were
changed (see netdev_update_features()), which will cause a netdev
notifier to be called without any actual changes. Fix this by returning
0 if ndo_set_features fails.

Fixes: 6cb6a27c

 ("net: Call netdev_features_change() from netdev_update_features()")
CC: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 705e63d2 upstream.

There is a bit of a mess in the order of arguments to the ulpi write
callback. There is

	int ulpi_write(struct ulpi *ulpi, u8 addr, u8 val)

in drivers/usb/common/ulpi.c;

	struct usb_phy_io_ops {
		...
		int (*write)(struct usb_phy *x, u32 val, u32 reg);
	}

in include/linux/usb/phy.h.

The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.

Fixes: ffb865b1

 ("usb: musb: add ulpi access operations")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit ed5a377d upstream.

now sctp auth cannot work well when setting a hmacid manually, which
is caused by that we didn't use the network order for hmacid, so fix
it by adding the transformation in sctp_auth_ep_set_hmacs.

even we set hmacid with the network order in userspace, it still
can't work, because of this condition in sctp_auth_ep_set_hmacs():

		if (id > SCTP_AUTH_HMAC_ID_MAX)
			return -EOPNOTSUPP;

so this wasn't working before and thus it won't break compatibility.

Fixes: 65b07e5d

 ("[SCTP]: API updates to suport SCTP-AUTH extensions.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit b582ef5c

 upstream.

Do not clobber the buffer space passed from `search_binary_handler' and
originally preloaded by `prepare_binprm' with the executable's file
header by overwriting it with its interpreter's file header.  Instead
keep the buffer space intact and directly use the data structure locally
allocated for the interpreter's file header, fixing a bug introduced in
2.1.14 with loadable module support (linux-mips.org commit beb11695
[Import of Linux/MIPS 2.1.14], predating kernel.org repo's history).
Adjust the amount of data read from the interpreter's file accordingly.

This was not an issue before loadable module support, because back then
`load_elf_binary' was executed only once for a given ELF executable,
whether the function succeeded or failed.

With loadable module support supported and enabled, upon a failure of
`load_elf_binary' -- which may for example be caused by architecture
code rejecting an executable due to a missing hardware feature requested
in the file header -- a module load is attempted and then the function
reexecuted by `search_binary_handler'.  With the executable's file
header replaced with its interpreter's file header the executable can
then be erroneously accepted in this subsequent attempt.

Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>