[202]HELLO! BOOT0 is starting!
[205]BOOT0 commit : d4861f2
[208]set pll start
[210]fix vccio detect value:0xc0
[213]periph0 has been enabled
[216]set pll end
[217][pmu]: bus read error
[220]board init ok
[222]get_pmu_exist() = -1
[224]ddr_efuse_type: 0x0
[227]trefi:7.8ms
[229][AUTO DEBUG] two rank and full DQ!
[233]ddr_efuse_type: 0x0
[235]trefi:7.8ms
[237][AUTO DEBUG] rank 0 row = 15
[241][AUTO DEBUG] rank 0 bank = 8
[244][AUTO DEBUG] rank 0 page size = 2 KB
[248][AUTO DEBUG] rank 1 row = 15
[251][AUTO DEBUG] rank 1 bank = 8
[254][AUTO DEBUG] rank 1 page size = 2 KB
[258]rank1 config same as rank0
[261]DRAM BOOT DRIVE INFO: V0.33
[264]DRAM CLK = 792 MHz
[266]DRAM Type = 3 (2:DDR2,3:DDR3)
[269]DRAMC ZQ value: 0x7b7bfb
[272]DRAM ODT value: 0x42.
[275]ddr_efuse_type: 0x0
[278]DRAM SIZE =1024 M
[280]dram_tpr4:0x0
[282]PLL_DDR_CTRL_REG:0xf8004100
[285]DRAM_CLK_REG:0xc0000000
[287][TIMING DEBUG] MR2= 0x18
[292]DRAM simple test OK.
[294]dram size =1024
[296]card no is 0
[298]sdcard 0 line count 4
[300][mmc]: mmc driver ver 2021-04-2 16:45
[309][mmc]: Wrong media type 0x0
[312][mmc]: ***Try SD card 0***
[331][mmc]: HSSDR52/SDR25 4 bit
[334][mmc]: 50000000 Hz
[336][mmc]: 30436 MB
[338][mmc]: ***SD/MMC 0 init OK!!!***
[387]Loading boot-pkg Succeed(index=0).
[390]Entry_name = opensbi
[393]Entry_name = u-boot
[397]Entry_name = dtb
[399]mmc not para
[401]Jump to second Boot.
OpenSBI v0.6
____ _____ ____ _____
/ __ \ / ____| _ \_ _|
| | | |_ __ ___ _ __ | (___ | |_) || |
| | | | '_ \ / _ \ '_ \ \___ \| _ < | |
| |__| | |_) | __/ | | |____) | |_) || |_
\____/| .__/ \___|_| |_|_____/|____/_____|
| |
|_|
Platform Name : T-HEAD Xuantie Platform
Platform HART Features : RV64ACDFIMSUVX
Platform Max HARTs : 1
Current Hart : 0
Firmware Base : 0x41fc0400
Firmware Size : 75 KB
Runtime SBI Version : 0.2
MIDELEG : 0x0000000000000222
MEDELEG : 0x000000000000b1ff
PMP0 : 0x0000000041fc0000-0x0000000041fdffff (A)
PMP1 : 0x0000000040000000-0x000000007fffffff (A,R,W,X)
PMP2 : 0x0000000080000000-0x00000000bfffffff (A,R,W,X)
PMP3 : 0x0000000000020000-0x0000000000027fff (A,▒
U-Boot 2018.05-gdc37958 (May 10 2022 - 07:38:00 +0000) Allwinner Technology
[00.484]DRAM: 1 GiB
[00.486]Relocation Offset is: 3dee7000
[00.490]secure enable bit: 0
[00.493]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.499]flash init start
[00.501]workmode = 0,storage type = 1
[00.505][mmc]: mmc driver ver uboot2018:2021-11-19 15:38:00
[00.510][mmc]: get sdc_type fail and use default host:tm1.
[00.516][mmc]: can't find node "mmc0",will add new node
[00.521][mmc]: fdt err returned <no error>
[00.525][mmc]: Using default timing para
[00.529][mmc]: SUNXI SDMMC Controller Version:0x50310
[00.555][mmc]: card_caps:0x3000000a
[00.558][mmc]: host_caps:0x3000003f
[00.563]sunxi flash init ok
[00.565]line:703 init_clocks
[00.568]drv_disp_init
fdt get node offset faill: hdmi
[00.580]unable to map hdmi registers
[00.583]drv_disp_init finish
[00.585]boot_gui_init:start
[00.588]set disp.dev0_output_type fail. using defval=0
partno erro : can't find partition Reserve0
[00.605]Get Reserve0 partition number fail!
no cfs of display devices.
[00.612]LCD open finish
[00.614]set disp.fb0_format fail. using defval=4294967295
[00.619]set disp.fb0_width fail. using defval=0
[00.623]set disp.fb0_height fail. using defval=0
bad fb0_cfg[w=0,h=0,bpp=32,format=-1]
[00.631]boot_gui_init:finish
partno erro : can't find partition bootloader
54 bytes read in 1 ms (52.7 KiB/s)
[00.652]bmp_name=bootlogo.bmp size 3072054
3072054 bytes read in 129 ms (22.7 MiB/s)
fb_lock: fb_id(0), lock=0
cv=0000000000000000, base= 0000000000000000
[00.796]show bmp on fb failed !-1
[00.810]Loading Environment from SUNXI_FLASH... OK
[00.852]Item0 (Map) magic is bad
[00.854]the secure storage item0 copy0 magic is bad
[00.880]Item0 (Map) magic is bad
[00.883]the secure storage item0 copy1 magic is bad
[00.888]Item0 (Map) magic is bad
[00.891]usb burn from boot
delay time 0
weak:otg_phy_config
[00.902]usb prepare ok
[01.705]overtime
[01.709]do_burn_from_boot usb : no usb exist
partno erro : can't find partition private
root_partition is rootfs
set root to /dev/mmcblk0p5
[01.722]update part info
[01.726]update bootcmd
[01.729]change working_fdt 0x7eaa6da0 to 0x7ea86da0
disable nand error: FDT_ERR_BADPATH
No reserved memory region found in source FDT
fb_save_para: fb_id(0), lock=0
[01.759]update dts
noncached_alloc(): addr = 0x7eb108c0
noncached_alloc(): addr = 0x7eb10900
noncached_alloc(): addr = 0x7eb10940
noncached_alloc(): addr = 0x7eb11180
phy_mode=rgmii, phy_interface=7
gmac: *** using ephy_clk ***
eth0
Warning: eth0 (eth0) using random MAC address - fa:43:5a:0a:0f:93
Hit any key to stop autoboot: 0
dsp0:gpio init config fail
dsp0:sharespace config fail
dsp0 version is r528-tina-v1.0.0-release-37-g735b6b4-dirty
DSP0 start ok, img length 254860, booting from 0x400660
[02.060]no vendor_boot partition is found
Android's image name: d1-h-nezha
Detect comp gzip
[02.315]
Starting kernel ...
[02.318][mmc]: MMC Device 2 not found
[02.321][mmc]: mmc 2 not find, so not exit
[ 0.000000] Linux version 5.4.61 (oe-user@oe-host) (riscv64-oe-linux-gcc (GCC) 11.2.0, GNU ld (GNU Binutils) 2.37.20210721) #1 PREEMPT Fri May 6 02:53:34 UTC 2022
[ 0.000000] cma: Reserved 8 MiB at 0x000000007f800000
[ 0.000000] Zone ranges:
[ 0.000000] DMA32 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] DMA32 zone: 3584 pages used for memmap
[ 0.000000] DMA32 zone: 0 pages reserved
[ 0.000000] DMA32 zone: 262144 pages, LIFO batch:63
[ 0.000000] elf_hwcap is 0x20112d
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258560
[ 0.000000] Kernel command line: earlyprintk=sunxi-uart,0x02500000 clk_ignore_unused initcall_debug=0 console=ttyS0,115200 loglevel=8 root=/dev/mmcblk0p5 rw init=/sbin/init partitions=boot-resource@mmcblk0p1:env@mmcblk0p2:env-redund@mmcblk0p3:boot@mmcblk0p4:rootfs@mmcblk0p5:dsp0@mmcblk0p6:recovery@mmcblk0p7:UDISK@mmcblk0p8 cma=8M snum= mac_addr= wifi_mac= bt_mac= specialstr= gpt=1 androidboot.hardware=sun20iw1p1 boot_type=1 androidboot.boot_type=1 gpt=1 uboot_message=2018.05-gdc37958(05/10/2022-07:38:00) mbr_offset=1556480 disp_reserve=12
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Sorting __ex_table...
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 1013256K/1048576K available (6446K kernel code, 669K rwdata, 2126K rodata, 184K init, 251K bss, 27128K reserved, 8192K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 0, nr_irqs: 0, preallocated irqs: 0
[ 0.000000] plic: mapped 200 interrupts with 1 handlers for 2 contexts.
[ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [0]
[ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000005] sched_clock: 64 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000021] riscv_timer_clockevent depends on broadcast, but no broadcast function available
[ 0.000295] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000859] Console: colour dummy device 80x25
[ 0.000898] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000916] pid_max: default: 32768 minimum: 301
[ 0.001074] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.001098] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.002623] ASID allocator initialised with 65536 entries
[ 0.002776] rcu: Hierarchical SRCU implementation.
[ 0.003408] devtmpfs: initialized
[ 0.016607] random: get_random_u32 called from bucket_table_alloc.isra.0+0x4e/0x150 with crng_init=0
[ 0.017208] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.017236] futex hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.017603] pinctrl core: initialized pinctrl subsystem
[ 0.018742] NET: Registered protocol family 16
[ 0.020314] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.020821] cpuidle: using governor menu
[ 0.059629] rtc_ccu: sunxi ccu init OK
[ 0.065973] clock: sunxi ccu init OK
[ 0.066812] clock: sunxi ccu init OK
[ 0.101751] iommu: Default domain type: Translated
[ 0.101904] sunxi iommu: irq = 4
[ 0.102936] SCSI subsystem initialized
[ 0.103227] usbcore: registered new interface driver usbfs
[ 0.103298] usbcore: registered new interface driver hub
[ 0.103394] usbcore: registered new device driver usb
[ 0.103555] mc: Linux media interface: v0.10
[ 0.103602] videodev: Linux video capture interface: v2.00
[ 0.104557] sunxi-msgbox-amp 3003000.msgbox: invalid resource
[ 0.105293] Advanced Linux Sound Architecture Driver Initialized.
[ 0.105802] Bluetooth: Core ver 2.22
[ 0.105872] NET: Registered protocol family 31
[ 0.105883] Bluetooth: HCI device and connection manager initialized
[ 0.105901] Bluetooth: HCI socket layer initialized
[ 0.105914] Bluetooth: L2CAP socket layer initialized
[ 0.105949] Bluetooth: SCO socket layer initialized
[ 0.106214] pwm module init!
[ 0.107674] g2d 5410000.g2d: Adding to iommu group 0
[ 0.108113] G2D: rcq version initialized.major:250
[ 0.108720] input: sunxi-keyboard as /devices/virtual/input/input0
[ 0.109841] clocksource: Switched to clocksource riscv_clocksource
[ 0.120695] sun8iw20-pinctrl 2000000.pinctrl: initialized sunXi PIO driver
[ 0.135154] thermal_sys: Registered thermal governor 'user_space'
[ 0.135160] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.135643] NET: Registered protocol family 2
[ 0.136365] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[ 0.136422] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.136526] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.136602] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.136764] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.136822] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.137049] NET: Registered protocol family 1
[ 0.139071] Initialise system trusted keyrings
[ 0.139308] workingset: timestamp_bits=62 max_order=18 bucket_order=0
[ 0.145501] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.166373] Key type asymmetric registered
[ 0.166387] Asymmetric key parser 'x509' registered
[ 0.166409] io scheduler mq-deadline registered
[ 0.166418] io scheduler kyber registered
[ 0.166438] atomic64_test: passed
[ 0.167527] [DISP]disp_module_init
[ 0.168036] disp 5000000.disp: Adding to iommu group 0
[ 0.201325] display_fb_request,fb_id:0
[ 0.228391] [DISP] Fb_copy_boot_fb,line:1443:
[ 0.228395] no boot_fb0
[ 0.228802] disp_al_manager_apply ouput_type:0
[ 0.229061] [DISP] lcd_clk_config,line:732:
[ 0.229073] disp 0, clk: pll(420000000),clk(420000000),dclk(70000000) dsi_rate(70000000)
[ 0.229073] clk real:pll(420000000),clk(420000000),dclk(105000000) dsi_rate(150000000)
[ 0.229916] [DISP]disp_module_init finish
[ 0.230732] sunxi_sid_init()551 - insmod ok
[ 0.231236] pwm-regulator: supplied by regulator-dummy
[ 0.237912] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pb not found, using dummy regulator
[ 0.238455] uart uart0: get regulator failed
[ 0.238483] uart uart0: uart0 supply uart not found, using dummy regulator
[ 0.238770] uart0: ttyS0 at MMIO 0x2500000 (irq = 18, base_baud = 1500000) is a SUNXI
[ 0.238798] sw_console_setup()1807 - console setup baud 115200 parity n bits 8, flow n
[ 0.298027] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pd not found, using dummy regulator
[ 0.630090] [DISP] disp_device_attached_and_enable,line:233:
[ 0.630096] attached ok, mgr0<-->dev0
[ 0.630101] [DISP] disp_device_attached_and_enable,line:236:
[ 0.630109] type:1,mode:0,fmt:rgb,bits:8bits,eotf:4,cs:0 dvi_hdmi:2, range:2 scan:0 ratio:8
[ 1.021963] printk: console [ttyS0] enabled
[ 1.027507] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pg not found, using dummy regulator
[ 1.038916] uart uart1: get regulator failed
[ 1.043783] uart uart1: uart1 supply uart not found, using dummy regulator
[ 1.051769] uart1: ttyS1 at MMIO 0x2500400 (irq = 19, base_baud = 1500000) is a SUNXI
[ 1.061626] misc dump reg init
[ 1.065888] sunxi-rfkill soc@3000000:rfkill@0: module version: v1.0.9
[ 1.073133] sunxi-rfkill soc@3000000:rfkill@0: get gpio chip_en failed
[ 1.080496] sunxi-rfkill soc@3000000:rfkill@0: get gpio power_en failed
[ 1.087892] sunxi-rfkill soc@3000000:rfkill@0: wlan_busnum (1)
[ 1.094459] sunxi-rfkill soc@3000000:rfkill@0: Missing wlan_power.
[ 1.101394] sunxi-rfkill soc@3000000:rfkill@0: wlan clock[0] (32k-fanout1)
[ 1.109112] sunxi-rfkill soc@3000000:rfkill@0: wlan_regon gpio=204 assert=1
[ 1.116978] sunxi-rfkill soc@3000000:rfkill@0: wlan_hostwake gpio=202 assert=1
[ 1.125150] sunxi-rfkill soc@3000000:rfkill@0: wakeup source is enabled
[ 1.132771] sunxi-rfkill soc@3000000:rfkill@0: Missing bt_power.
[ 1.139517] sunxi-rfkill soc@3000000:rfkill@0: bt clock[0] (32k-fanout1)
[ 1.147057] sunxi-rfkill soc@3000000:rfkill@0: bt_rst gpio=210 assert=0
[ 1.155256] [ADDR_MGT] addr_mgt_probe: module version: v1.0.10
[ 1.162760] [ADDR_MGT] addr_mgt_probe: success.
[ 1.168980] libphy: Fixed MDIO Bus: probed
[ 1.173661] CAN device driver interface
[ 1.178988] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pe not found, using dummy regulator
[ 1.190352] sunxi gmac driver's version: 1.0.0
[ 1.195455] gmac-power0: NULL
[ 1.198763] gmac-power1: NULL
[ 1.202109] gmac-power2: NULL
[ 1.206633] Failed to alloc md5
[ 1.210226] eth0: Use random mac address
[ 1.214930] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.222343] sunxi-ehci: EHCI SUNXI driver
[ 1.227316] get ehci1-controller wakeup-source is fail.
[ 1.233326] sunxi ehci1-controller don't init wakeup source
[ 1.239577] [sunxi-ehci1]: probe, pdev->name: 4200000.ehci1-controller, sunxi_ehci: 0xffffffe000963f50, 0x:ffffffd00407a000, irq_no:31
[ 1.253184] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply drvvbus not found, using dummy regulator
[ 1.265683] sunxi-ehci 4200000.ehci1-controller: 4200000.ehci1-controller supply hci not found, using dummy regulator
[ 1.277958] sunxi-ehci 4200000.ehci1-controller: EHCI Host Controller
[ 1.285266] sunxi-ehci 4200000.ehci1-controller: new USB bus registered, assigned bus number 1
[ 1.295088] sunxi-ehci 4200000.ehci1-controller: irq 49, io mem 0x04200000
[ 1.329885] sunxi-ehci 4200000.ehci1-controller: USB 2.0 started, EHCI 1.00
[ 1.338591] hub 1-0:1.0: USB hub found
[ 1.342890] hub 1-0:1.0: 1 port detected
[ 1.348044] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.355071] sunxi-ohci: OHCI SUNXI driver
[ 1.360128] get ohci1-controller wakeup-source is fail.
[ 1.366058] sunxi ohci1-controller don't init wakeup source
[ 1.372366] [sunxi-ohci1]: probe, pdev->name: 4200400.ohci1-controller, sunxi_ohci: 0xffffffe000964aa8
[ 1.382842] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply drvvbus not found, using dummy regulator
[ 1.395312] sunxi-ohci 4200400.ohci1-controller: 4200400.ohci1-controller supply hci not found, using dummy regulator
[ 1.407534] sunxi-ohci 4200400.ohci1-controller: OHCI Host Controller
[ 1.414800] sunxi-ohci 4200400.ohci1-controller: new USB bus registered, assigned bus number 2
[ 1.424650] sunxi-ohci 4200400.ohci1-controller: irq 50, io mem 0x04200400
[ 1.504813] hub 2-0:1.0: USB hub found
[ 1.509045] hub 2-0:1.0: 1 port detected
[ 1.514518] usbcore: registered new interface driver uas
[ 1.520659] usbcore: registered new interface driver usb-storage
[ 1.527434] usbcore: registered new interface driver ums-alauda
[ 1.534222] usbcore: registered new interface driver ums-cypress
[ 1.541026] usbcore: registered new interface driver ums-datafab
[ 1.547818] usbcore: registered new interface driver ums_eneub6250
[ 1.554813] usbcore: registered new interface driver ums-freecom
[ 1.561660] usbcore: registered new interface driver ums-isd200
[ 1.568321] usbcore: registered new interface driver ums-jumpshot
[ 1.575217] usbcore: registered new interface driver ums-karma
[ 1.581881] usbcore: registered new interface driver ums-onetouch
[ 1.588753] usbcore: registered new interface driver ums-realtek
[ 1.595606] usbcore: registered new interface driver ums-sddr09
[ 1.602313] usbcore: registered new interface driver ums-sddr55
[ 1.608974] usbcore: registered new interface driver ums-usbat
[ 1.616097] sunxi_gpadc_init,2151, success
[ 1.621586] sunxi-rtc 7090000.rtc: errata__fix_alarm_day_reg_default_value(): ALARM0_DAY_REG=0, set it to 1
[ 1.633819] sunxi-rtc 7090000.rtc: registered as rtc0
[ 1.639567] sunxi-rtc 7090000.rtc: setting system clock to 1970-01-01T00:00:04 UTC (4)
[ 1.648524] sunxi-rtc 7090000.rtc: sunxi rtc probed
[ 1.654446] i2c /dev entries driver
[ 1.658437] IR NEC protocol handler initialized
[ 1.664204] sunxi cedar version 1.1
[ 1.668357] sunxi-cedar 1c0e000.ve: Adding to iommu group 0
[ 1.674646] VE: install start!!!
[ 1.674646]
[ 1.680207] VE: cedar-ve the get irq is 6
[ 1.680207]
[ 1.686499] VE: ve_debug_proc_info:(____ptrval____), data:(____ptrval____), lock:(____ptrval____)
[ 1.686499]
[ 1.698124] VE: install end!!!
[ 1.698124]
[ 1.703196] VE: sunxi_cedar_probe
[ 1.708480] sunxi-wdt 6011000.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 1.717609] Bluetooth: HCI UART driver ver 2.3
[ 1.722606] Bluetooth: HCI UART protocol H4 registered
[ 1.728360] Bluetooth: HCI UART protocol BCSP registered
[ 1.734306] Bluetooth: XRadio Bluetooth LPM Mode Driver Ver 1.0.10
[ 1.741597] [XR_BT_LPM] bluesleep_probe: bt_wake polarity: 1
[ 1.747966] [XR_BT_LPM] bluesleep_probe: host_wake polarity: 1
[ 1.754540] [XR_BT_LPM] bluesleep_probe: wakeup source is disabled!
[ 1.754540]
[ 1.763249] [XR_BT_LPM] bluesleep_probe: uart_index(1)
[ 1.771964] sunxi-mmc 4020000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.21 2021-11-18 10:02)
[ 1.781964] sunxi-mmc 4020000.sdmmc: ***ctl-spec-caps*** 8
[ 1.788133] sunxi-mmc 4020000.sdmmc: No vmmc regulator found
[ 1.794524] sunxi-mmc 4020000.sdmmc: No vqmmc regulator found
[ 1.800959] sunxi-mmc 4020000.sdmmc: No vdmmc regulator found
[ 1.807384] sunxi-mmc 4020000.sdmmc: No vd33sw regulator found
[ 1.813912] sunxi-mmc 4020000.sdmmc: No vd18sw regulator found
[ 1.820439] sunxi-mmc 4020000.sdmmc: No vq33sw regulator found
[ 1.826959] sunxi-mmc 4020000.sdmmc: No vq18sw regulator found
[ 1.833909] sunxi-mmc 4020000.sdmmc: Got CD GPIO
[ 1.839408] sunxi-mmc 4020000.sdmmc: set cd-gpios as 24M fail
[ 1.846051] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 1.857227] sunxi-mmc 4020000.sdmmc: no vqmmc,Check if there is regulator
[ 1.877380] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 1.901779] sunxi-mmc 4020000.sdmmc: detmode:gpio irq
[ 1.907491] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 1.919763] sunxi-mmc 4021000.sdmmc: SD/MMC/SDIO Host Controller Driver(v4.21 2021-11-18 10:02)
[ 1.929824] sunxi-mmc 4021000.sdmmc: ***ctl-spec-caps*** 8
[ 1.936104] sunxi-mmc 4021000.sdmmc: No vmmc regulator found
[ 1.942490] sunxi-mmc 4021000.sdmmc: No vqmmc regulator found
[ 1.948928] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 1.960536] sunxi-mmc 4021000.sdmmc: No vdmmc regulator found
[ 1.966944] sunxi-mmc 4021000.sdmmc: No vd33sw regulator found
[ 1.973605] sunxi-mmc 4021000.sdmmc: No vd18sw regulator found
[ 1.980166] sunxi-mmc 4021000.sdmmc: No vq33sw regulator found
[ 1.986727] sunxi-mmc 4021000.sdmmc: No vq18sw regulator found
[ 1.993317] sunxi-mmc 4021000.sdmmc: Cann't get pin bias hs pinstate,check if needed
[ 2.002037] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.014661] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.025880] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator
[ 2.034819] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.046404] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.070730] sunxi-mmc 4021000.sdmmc: detmode:manually by software
[ 2.078383] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 2.085578] sun8iw20-pinctrl 2000000.pinctrl: 2000000.pinctrl supply vcc-pc not found, using dummy regulator
[ 2.096560] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !!
[ 2.103477] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.115283] sunxi_led_probe()1749 - start
[ 2.119965] sunxi_get_str_of_property()1595 - failed to get the string of propname led_regulator!
[ 2.129991] sunxi_register_led_classdev()1483 - led_classdev start
[ 2.138261] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[ 2.153081] sunxi_led_probe()1845 - finish
[ 2.157682] mmc0: host does not support reading read-only switch, assuming write-enable
[ 2.167259] usbcore: registered new interface driver usbhid
[ 2.173657] usbhid: USB HID core driver
[ 2.177996] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 2.189648] rpmsg_client_dsp_standby 3003000.msgbox.sunxi,dsp-power-msgbox.512.256: new channel: 0x200 -> 0x100!
[ 2.201016] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.207907] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B
[ 2.219563] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.227177] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.234777] sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
[ 2.241557] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[ 2.252909] usbcore: registered new interface driver snd-usb-audio
[ 2.263545] sunxi-daudio 2034000.daudio: regulator missing or invalid
[ 2.270825] sunxi-mmc 4020000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B
[ 2.283635] [AUDIOCODEC][sunxi_codec_parse_params][2404]:digital_vol:0, lineout_vol:26, mic1gain:19, mic2gain:19 pa_msleep:120, pa_level:1, pa_pwr_level:1
[ 2.283635]
[ 2.300888] mmc0: new high speed SDHC card at address aaaa
[ 2.308162] mmcblk0: mmc0:aaaa SD32G 29.7 GiB
[ 2.315236] [AUDIOCODEC][sunxi_codec_parse_params][2444]:adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:0, dachpf:0
[ 2.326878] [AUDIOCODEC][sunxi_internal_codec_probe][2609]:codec probe finished
[ 2.335841] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 2.341615] debugfs: Directory '203034c.dummy_cpudai' with parent 'audiocodec' already present!
[ 2.353941] [SNDCODEC][sunxi_card_init][583]:card init finished
[ 2.362854] sunxi-codec-machine 2030340.sound: 2030000.codec <-> 203034c.dummy_cpudai mapping ok
[ 2.374138] input: audiocodec sunxi Audio Jack as /devices/platform/soc@3000000/2030340.sound/sound/card0/input1
[ 2.386202] [SNDCODEC][sunxi_card_dev_probe][836]:register card finished
[ 2.394451] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: register device finished!
[ 2.402964] sunxi-rpaf-dsp soc@3000000:rpaf-dsp@203034c: [rpaf_dsp0] probe finished!
[ 2.412048] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: id:sunxi,dsp-msgbox new channel: 0x202 -> 0x102!
[ 2.423641] rpmsg_hifi 3003000.msgbox.sunxi,dsp-msgbox.514.258: rpmsg hifi[0] client driver is probed
[ 2.435537] NET: Registered protocol family 10
[ 2.441952] Segment Routing with IPv6
[ 2.446196] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 2.453636] NET: Registered protocol family 17
[ 2.458686] can: controller area network core (rev 20170425 abi 9)
[ 2.465750] NET: Registered protocol family 29
[ 2.470777] can: raw protocol (rev 20170425)
[ 2.475566] can: broadcast manager protocol (rev 20170425 t)
[ 2.481917] can: netlink gateway (rev 20190810) max_hops=1
[ 2.488354] Bluetooth: RFCOMM TTY layer initialized
[ 2.493906] Bluetooth: RFCOMM socket layer initialized
[ 2.499660] Bluetooth: RFCOMM ver 1.11
[ 2.504660] Loading compiled-in X.509 certificates
[ 2.512235] HDMI 2.0 driver init start!
[ 2.516529] boot_hdmi=false
[ 2.519737] ERROR: pinctrl_get for HDMI2.0 DDC fail
[ 2.526767] HDMI2.0 module init end
[ 2.549334] sunxi-i2c sunxi-i2c2: sunxi-i2c2 supply twi not found, using dummy regulator
[ 2.565075] pcf857x 2-0038: probed
[ 2.569005] sunxi-i2c sunxi-i2c2: probe success
[ 2.578141] debugfs: Directory '2031000.dmic' with parent 'snddmic' already present!
[ 2.588375] sunxi-audio-card 2031060.sounddmic: dmic-hifi <-> 2031000.dmic mapping ok
[ 2.598453] debugfs: Directory '2034000.daudio' with parent 'sndhdmi' already present!
[ 2.609087] sunxi-audio-card 20340a0.sounddaudio2: 20340a4.hdmiaudio <-> 2034000.daudio mapping ok
[ 2.620511] get ehci0-controller wakeup-source is fail.
[ 2.626437] sunxi ehci0-controller don't init wakeup source
[ 2.632722] [sunxi-ehci0]: probe, pdev->name: 4101000.ehci0-controller, sunxi_ehci: 0xffffffe000963b88, 0x:ffffffd004efe000, irq_no:2e
[ 2.646272] [sunxi-ehci0]: Not init ehci0
[ 2.651260] get ohci0-controller wakeup-source is fail.
[ 2.657191] sunxi ohci0-controller don't init wakeup source
[ 2.663452] [sunxi-ohci0]: probe, pdev->name: 4101400.ohci0-controller, sunxi_ohci: 0xffffffe0009646e0
[ 2.673911] [sunxi-ohci0]: Not init ohci0
[ 2.680699] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 2.691638] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 2.699089] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 2.708879] clk: Not disabling unused clocks
[ 2.713734] cfg80211: failed to load regulatory.db
[ 2.719177] ALSA device list:
[ 2.722570] #0: audiocodec
[ 2.725779] #1: snddmic
[ 2.728693] #2: sndhdmi
[ 2.731730] alloc_fd: slot 0 not NULL!
[ 2.787671] EXT4-fs (mmcblk0p5): recovery complete
[ 2.794793] EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: (null)
[ 2.803950] VFS: Mounted root (ext4 filesystem) on device 179:5.
[ 2.811442] devtmpfs: mounted
[ 2.814946] Freeing unused kernel memory: 184K
[ 2.819938] This architecture does not have kernel memory protection.
[ 2.827120] Run /sbin/init as init process
init started: BusyBox v1.34.1 ()
starting pid 78, tty '': '/bin/mount -t proc proc /proc'
mount: mounting proc on /proc failed: No such file or directory
[ 2.936630] random: fast init done
starting pid 79, tty '': '/bin/mount -t sysfs sysfs /sys'
mount: mounting sysfs on /sys failed: No such file or directory
starting pid 80, tty '': '/bin/mount -t devtmpfs devtmpfs /dev'
mount: mounting devtmpfs on /dev failed: Device or resource busy
starting pid 81, tty '': '/bin/mount -o remount,rw /'
mount: can't read '/proc/mounts': No such file or directory
starting pid 82, tty '': '/bin/mkdir -p /dev/pts'
starting pid 83, tty '': '/bin/mount -t devpts devpts /dev/pts'
starting pid 84, tty '': '/bin/mount -a'
mount: can't read '/etc/fstab': No such file or directory
starting pid 85, tty '': '/sbin/swapon -a'
swapon: can't open '/etc/fstab': No such file or directory
starting pid 91, tty '': '/etc/init.d/rcS'
can't run '/etc/init.d/rcS': No such file or directory
starting pid 92, tty '/dev/ttyS0': '/sbin/getty 115200 ttyS0'
(none) login: [ 6.119870] hdmi_hpd_sys_config_release
root
login[92]: root login on 'ttyS0'
~ # uname -a
Linux (none) 5.4.61 #1 PREEMPT Fri May 6 02:53:34 UTC 2022 riscv64 GNU/Linux