Commit dcb27bee authored by Dmitry Lifshitz's avatar Dmitry Lifshitz Committed by Tony Lindgren
Browse files

ARM: dts: cm-t3x30: add USB OTG support 



Add USB OTG support for cm-t3x30 CoMs.

Signed-off-by: default avatarDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 3f88afdf

arch/arm/boot/dts/omap3-cm-t3x30.dtsi

+28 −0
Original line number Diff line number Diff line
@@ -32,6 +32,23 @@ OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */ 
			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */

		>;

	};



 	hsusb0_pins: pinmux_hsusb0_pins {

		pinctrl-single,pins = <

			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_clk.hsusb0_clk */

			OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0)		/* hsusb0_stp.hsusb0_stp */

			OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_dir.hsusb0_dir */

			OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_nxt.hsusb0_nxt */

			OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data0.hsusb2_data0 */

			OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data1.hsusb0_data1 */

			OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data2.hsusb0_data2 */

			OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data3 */

			OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data4 */

			OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data5 */

			OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data6 */

			OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* hsusb0_data7.hsusb0_data7 */

		>;

	};

};



&gpmc {
@@ -101,3 +118,14 @@ &hsusb1_phy { 
&hsusb2_phy {

	reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;

};



&usb_otg_hs {

	pinctrl-names = "default";

	pinctrl-0 = <&hsusb0_pins>;

	interface-type = <0>;

	usb-phy = <&usb2_phy>;

	phys = <&usb2_phy>;

	phy-names = "usb2-phy";

	mode = <3>;

	power = <50>;

};